Craftsman 139.53993D owner manual Position the Opener, Sectional Door or ONE-PIECE Door with Track

Page 18

INSTALLATION STEP 5

Position the Opener

Follow instructions which apply to your door type as illustrated.

SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK

A 2x4 laid flat is convenient for setting an ideal door-to- rail distance.

Remove foam packaging.

Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough.

Open the door all the way and place a 2x4 laid flat on the top section beneath the rail.

If the top section or panel hits the trolley when you

raise the door, pull down on the trolley release arm

to disconnect inner and outer sections. Slide the outer trolley toward the motor unit. The trolley can remain disconnected until Installation Step 13 is completed.

--Release Arm Trolley

ENGAGED

RELEASED

ONE-PIECE DOOR WITHOUT TRACK

A 2x4 on its side is convenient for setting an ideal door- to-rail distance.

Remove foam packaging.

Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough.

Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail.

The top of the door should be level with the top of the motor unit. Do not position the opener more than 4" (10 cm) above this point.

To prevent damageto garage door, rest garage door opener rail on 2x4 placed on top section of door.

_j "--°_-::-%?_ ,

_

t

_)

Top of Door

ili

<Y_I Door

2x4 is used to

determine

 

 

;herrCO_,_tg?O

unti ng height

 

18

Image 18
Contents Abridor DE Puerta DE Cochera DE 315MN= Contents IntroductionTools needed Preparing your garage doorPlanning Sectional Door InstallationSectional Door Installations Finished CeilingONE-PIECE Door with Track ONE-PIECE Door InstallationsONE-PIECE Door Without Track Finished CeungCarton Inventory SECURITY+Assembly Hardware Installation HardwareHardware Inventory Assembly Step Assemble the RailHardware Shown Actual Size Fasten the Rail to the Motor Unit Install the Trolley Installation Readand Followall Installationwarningsand InstructionsAttach the Rail Brackets Installation Step Determine the Header Bracket LocationInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Attach the Rail to the Header Bracket Install The Protector System Important Information about Safety Reversing SensorWall installation Installing the BracketsGarage door track installation preferred Floor installation FigureMounting and Wiring the Safety Sensors Recommended Wire RoutingPosition the Opener Sectional Door or ONE-PIECE Door with TrackEngaged Released Hang the Opener Fenshed Ceung Hardware Shown Actual SizeInstall Door Control Troubleshooting the Safety Reversing Sensors Complete the Safety Reversing Sensor InstallationAligning the Safety Reversing Sensors Permanent Wiring ConnectionInstall the Lights Attach the Emergency Release Rope and HandleFasten the Door Bracket Sectional DoorsONE-PIECEDOORS Connect Door Arm to Trolley Sectional Doors onlyAssemble the door arm, Figure Adjustment procedures, FigureALL ONE-PIECE Doors Connect the door arm to the trolleyHOW and When to Adjust the Limits Adjustment StepAdjust the Travel Limits If door does not open at least 5 feet 1.5 mTest the Down close force Adjust the ForceHOW and When to Adjust the Forces Test the UP open forceImportant Safety Check Test the Safety Reversal SystemAdjust Test The Protector SystemUsing Your Garage Door Opener OperationReadand Followall Warningsand Instructions Using the Wall.Mounted Door Control Light featureTo Open the Door Manually Once a Month Remote Control BatteryCare of Your Opener Once a YearHaving a PROBLEM? Refer to Adjustment , Adjust the ForceSymptom LED is not lit on door control Symptom Motor unit doesnt operateProgramming To Add or Reprogram a Hand-held Remote ControlUsing the Learn Button Using the Premium Control Console To Erase All Codes From Motor Unit MemoryEntry is already mounted outside the garage To Add Reprogram Change Keyless Entry PINMust be programmed To operate Your Garage door Opener To change an existing, known PINKEY Part NO. NO. Description Repair PartsRail Assembly Parts Installation Parts Not ShownMotor Unit Assembly Parts KEY PartKEY Part NO. NO.DESCRIPTION Service AccessoriesWarranty For Sectional Doors OnlyContenido IntroduccionPreparaci6n de la puerta de su cochera Herramientas necesariasInstalacion EN UNA Puerta Seccional Planificaci6nInstalacicn CON UNA Puerta Seccional Techo TERMI/ADOPuerta DE UNA Sola Pieza SIN Carril Planificaci6n continbaInstalacion CON Puertas DE UNA Sola Pieza Puerta DE UNA Pieza CON CarrilInventario de las caja de cart6n Inventario de Piezas Tornillera Y Piezas Para EL MontajeMontaje Paso Monte el rielMontaje el riel continba Estas Piezas SE Muestran EN SU Tamano RealFije el riel a la unidad del motor e instale el trole Estas Piezas SE Muestran EN SU Tamaiio RealLA Muerte Fijacibn de las mnsulas del rielCabezal Instalacion PasoDetermine dbnde va a instalar la Mnsula del Cabezal EltechoInstale la mnsula del cabezal Instalacion DE LA Mensula DEL Cabezal EN ELColocacibn del riel en la mnsula del cabezal Estas Piezas SE Muestran EN SU Tamaiio RealInstale la Sistema de Protecci6n Enfrentando la puerta desde el lado interno del garajeInstalaci6n en el piso Figura Instalacion DE LAS McnsulasInstalaci6n en la pared Figura 2 y Montajeparedlado DerechoRuta recomendada para el cableado Coloque el Abridor en Posici6n Puerta DE UNA Sola Pieza SIN RielEnganchado Desenganchado INSTALACION, Paso Cuelgue el AbridorInstale la unidad de control de la puerta Estas Piezas SE Muestran EN SU Tamaio RealQuitar Y Volvera Ponerlatapa Requisitos para la instalaci6n el6ctrica COMe Alinear LOS Sensores DE SeguridadInstale las Luces Coloque la Cuerda y la Manija De EmergenciaFije la mnsula de la puerta Puertas SeccionalesPuertas DE UNA Sola Pieza Conecte el brazo de la puerta al trole SLO Para Puertas SeccionalesTodas LAS Puertas DE UNA Sola Pieza Arme el brazo de la puerta, FiguraAjustes Paso Ajuste el limite del recorrido Hacia Arriba y Hacia AbajoCalcomanade Ajustes Ajuste de la fuerza Etiouetade Ajustede FuerzaPrueba Pruebe la Sistema de Protecci6nPruebe el Sistema de Retroceso de Seguridad AjusteC6mo Usar su Abridor de Puerta de Cochera ConserveestasinstruccionesOperacion Active su abridor de alguna de las siguientes manerasComo Desconectar EL Trole C6mo usar la unidad de control de paredC6mo abrir la puerta manualmente CMO Reconectar EL TroleMantenimiento DE SU Abridor DE Puerta DE Cochera Ajustes DE Lmite Y FuerzaSI Tiene Algon Problema El control remoto no activa la puertaTabla de Diag El motorComo Programar EL Abridor C6mo Agregar o Reprogramar un Control Remoto ManualControles Remotos de 3 Funciones Para cambiar un PIN existente Accesorios Riel de 2.4 m 8 piesNo.,a,,erw.orna1,,noe.,a,,erw.so,1

139.53993D specifications

The Craftsman 139.53993D is a top-tier garage door opener designed for efficiency, convenience, and durability. This model is part of Craftsman's renowned lineup, known for reliable home improvement products. With its advanced features and technology, this garage door opener offers users a blend of functionality and modern convenience.

One of the standout features of the Craftsman 139.53993D is its powerful motor. Equipped with a robust 1/2 horsepower motor, it delivers strong lifting power, making it suitable for handling standard residential garage doors with ease. This strength ensures a smooth and reliable operation, even for heavier doors.

The technology integrated into the Craftsman 139.53993D significantly enhances security. This model utilizes a rolling code technology that changes the code each time the remote is used, making it nearly impossible for intruders to gain access. The safety features extend to the presence of an infrared safety sensor, which detects any obstacles in the door’s path and reverses its direction, preventing accidents and injuries.

Convenience is a key characteristic of this garage door opener. The Craftsman 139.53993D is compatible with various remote controls, including a keypad entry, allowing for keyless entry. Additionally, the model includes an integrated Wi-Fi capability. This feature grants homeowners remote access via a mobile app, enabling them to monitor and control their garage door from anywhere, adding an extra layer of convenience.

Installation is user-friendly owing to its clear instructions and included components. Most users can set it up in a short timeframe without professional help. Furthermore, the design of the motor unit is compact, allowing for easy placement and ensuring that it does not take up excessive space in the garage.

Alongside its functionality, the Craftsman 139.53993D is built with durability in mind. It features all-steel construction, providing long-lasting reliability and strength, suitable for the demands of daily use. The quiet operation is another impressive feature, ensuring that the door opens and closes smoothly without causing disturbances.

In summary, the Craftsman 139.53993D garage door opener stands out with its powerful motor, advanced security features, convenient technology, and robust construction. It reflects Craftsman's commitment to quality and innovation in home improvement solutions, making it a dependable choice for homeowners seeking a reliable garage door opener.