Craftsman 139.53993D owner manual Fasten the Door Bracket, Sectional Doors

Page 23

INSTALLATION STEP 12

Fasten the Door Bracket

Follow instructions which apply to your door type as illustrated below or on the following page.

A horizontal reinforcement brace should be long

enough to be secured to two vertical supports. A vertical reinforcement brace should cover the height of the top panel.

The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, two pieces of angle iron are used to create a U-shaped support (Figure 1). The best solution is to check with your garage

door manufacturer for an opener installation door reinforcement kit.

NOTE: Many vertical brace installations provide for direct attachment of the clevis pin and door arm. In this case you will not need the door bracket; proceed to Installation Step 12.

SECTIONAL DOORS

•Center the door bracket on the previously marked vertical centerline used for the header bracket

installation. Note correct UP placement, as stamped inside the bracket (Figure 2).

•Position the bracket on the face of the door within the following limits:

A)The top edge of the bracket 2"-4" (5-10 cm) below the top edge of the door.

B)The top edge of the bracket directly below any structural support across the top of the door.

Header Bracket

/

Door

Bracket

Location

Vertical

of Garage

Door

Fiberglass,aluminum or lightweight steel garage doors WILL REQUIREreinforcement BEFOREinstallation of door bracket.

Contactyour door manufacturerfor reinforcement kit.

HARDWARE SHOWN ACTUAL SIZE

© ©

Nut 5/16"-18

Lock Washer 5/16"

Carriage Bolt 5/16"-18x2-1/2"

•Mark and drill 5/16" left and right fastening holes.

Secure the bracket as shown in Figure 1 if there is vertical reinforcement.

If your installation doesn't require vertical reinforcement but does need top and bottom fastening holes for the door bracket, fasten as shown in Figure 2.

Horizontal and vertical reinforcement

is needed for lightweight garage doors Uass, aluminum, steeU, doors with

glass panel etc.). (Not Provided)

Vertical Reinforcement

Vertical

,.'of Garage

Door

UP

Carriage Bolt

Edge5/16"-18x2-1/2' of Door or

Door

Reinforcement Board Bracket

Lock Washer

5/16"

Nut

5/16 "-18 z ....

Figure

Door Bracket

Figure 2

23

Image 23

Contents Abridor DE Puerta DE Cochera DE 315MN= Introduction ContentsPreparing your garage door Tools neededFinished Ceiling Sectional Door InstallationSectional Door Installations PlanningFinished Ceung ONE-PIECE Door InstallationsONE-PIECE Door Without Track ONE-PIECE Door with TrackSECURITY+ Carton InventoryHardware Inventory Assembly HardwareInstallation Hardware Assemble the Rail Assembly StepHardware Shown Actual Size Fasten the Rail to the Motor Unit Install the Trolley Attach the Rail Brackets InstallationReadand Followall Installationwarningsand Instructions Determine the Header Bracket Location Installation StepCeiling Header Bracket Installation Install the Header BracketWall Header Bracket Installation Attach the Rail to the Header Bracket Important Information about Safety Reversing Sensor Install The Protector SystemFloor installation Figure Installing the BracketsGarage door track installation preferred Wall installationRecommended Wire Routing Mounting and Wiring the Safety SensorsEngaged Released Position the OpenerSectional Door or ONE-PIECE Door with Track Fenshed Ceung Hardware Shown Actual Size Hang the Opener Install Door Control Permanent Wiring Connection Complete the Safety Reversing Sensor InstallationAligning the Safety Reversing Sensors Troubleshooting the Safety Reversing SensorsAttach the Emergency Release Rope and Handle Install the LightsSectional Doors Fasten the Door BracketONE-PIECEDOORS Sectional Doors only Connect Door Arm to TrolleyConnect the door arm to the trolley Adjustment procedures, FigureALL ONE-PIECE Doors Assemble the door arm, FigureIf door does not open at least 5 feet 1.5 m Adjustment StepAdjust the Travel Limits HOW and When to Adjust the LimitsTest the UP open force Adjust the ForceHOW and When to Adjust the Forces Test the Down close forceTest The Protector System Test the Safety Reversal SystemAdjust Important Safety CheckReadand Followall Warningsand Instructions Using Your Garage Door OpenerOperation To Open the Door Manually Using the Wall.Mounted Door ControlLight feature Once a Year Remote Control BatteryCare of Your Opener Once a MonthRefer to Adjustment , Adjust the Force Having a PROBLEM?Symptom Motor unit doesnt operate Symptom LED is not lit on door controlTo Erase All Codes From Motor Unit Memory To Add or Reprogram a Hand-held Remote ControlUsing the Learn Button Using the Premium Control Console ProgrammingTo change an existing, known PIN To Add Reprogram Change Keyless Entry PINMust be programmed To operate Your Garage door Opener Entry is already mounted outside the garageNot Shown Repair PartsRail Assembly Parts Installation Parts KEY Part NO. NO. DescriptionKEY Part NO. NO.DESCRIPTION Motor Unit Assembly PartsKEY Part For Sectional Doors Only AccessoriesWarranty ServiceIntroduccion ContenidoHerramientas necesarias Preparaci6n de la puerta de su cocheraTecho TERMI/ADO Planificaci6nInstalacicn CON UNA Puerta Seccional Instalacion EN UNA Puerta SeccionalPuerta DE UNA Pieza CON Carril Planificaci6n continbaInstalacion CON Puertas DE UNA Sola Pieza Puerta DE UNA Sola Pieza SIN CarrilInventario de las caja de cart6n Tornillera Y Piezas Para EL Montaje Inventario de PiezasMonte el riel Montaje PasoEstas Piezas SE Muestran EN SU Tamano Real Montaje el riel continbaEstas Piezas SE Muestran EN SU Tamaiio Real Fije el riel a la unidad del motor e instale el troleFijacibn de las mnsulas del riel LA MuerteEltecho Instalacion PasoDetermine dbnde va a instalar la Mnsula del Cabezal CabezalInstalacion DE LA Mensula DEL Cabezal EN EL Instale la mnsula del cabezalEstas Piezas SE Muestran EN SU Tamaiio Real Colocacibn del riel en la mnsula del cabezalEnfrentando la puerta desde el lado interno del garaje Instale la Sistema de Protecci6nMontajeparedlado Derecho Instalacion DE LAS McnsulasInstalaci6n en la pared Figura 2 y Instalaci6n en el piso FiguraRuta recomendada para el cableado Enganchado Desenganchado Coloque el Abridor en Posici6nPuerta DE UNA Sola Pieza SIN Riel Cuelgue el Abridor INSTALACION, PasoQuitar Y Volvera Ponerlatapa Instale la unidad de control de la puertaEstas Piezas SE Muestran EN SU Tamaio Real COMe Alinear LOS Sensores DE Seguridad Requisitos para la instalaci6n el6ctricaColoque la Cuerda y la Manija De Emergencia Instale las LucesPuertas Seccionales Fije la mnsula de la puertaPuertas DE UNA Sola Pieza SLO Para Puertas Seccionales Conecte el brazo de la puerta al troleArme el brazo de la puerta, Figura Todas LAS Puertas DE UNA Sola PiezaCalcomanade Ajustes Ajustes PasoAjuste el limite del recorrido Hacia Arriba y Hacia Abajo Etiouetade Ajustede Fuerza Ajuste de la fuerzaAjuste Pruebe la Sistema de Protecci6nPruebe el Sistema de Retroceso de Seguridad PruebaActive su abridor de alguna de las siguientes maneras ConserveestasinstruccionesOperacion C6mo Usar su Abridor de Puerta de CocheraCMO Reconectar EL Trole C6mo usar la unidad de control de paredC6mo abrir la puerta manualmente Como Desconectar EL TroleAjustes DE Lmite Y Fuerza Mantenimiento DE SU Abridor DE Puerta DE CocheraEl control remoto no activa la puerta SI Tiene Algon ProblemaEl motor Tabla de DiagControles Remotos de 3 Funciones Como Programar EL AbridorC6mo Agregar o Reprogramar un Control Remoto Manual Para cambiar un PIN existente Riel de 2.4 m 8 pies AccesoriosNo.,a,,erw.orna1,,noe.,a,,erw.so,1