Craftsman 139.53993D owner manual Tools needed, Preparing your garage door

Page 3

Preparing your garage door

Before you begin:

•Disable locks.

•Remove any ropes connected to garage door.

•Complete the following test to make sure your garage door is balanced and is not sticking or binding:

1.Lift the door about halfway as shown. Release the door. If balanced, it should stay in place, supported entirely by its springs.

2.Raise and lower the door to see if there is any binding or sticking.

If your door binds, sticks, or is out of balance, call a trained door systems technician.

Sectional Door

One-Piece Door

To prevent possible SERIOUSINJURYor DEATH:

•ALWAYScall atrained door systems technician if garage door binds, sticks, or is out of balance An unbalanced garage door may not reversewhen required

•NEVERtry to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their hardware,all of which are under EXTREMEtension

•Disable ALL locks and removeALL ropes connected to garage door BEFOREinstalling and operating garagedoor opener to avoid entanglement.

To prevent damageto garage door and opener:

•ALWAYSdisable locks BEFOREinstalling and operating the opener.

•ONLYoperate garagedoor opener at 120V,60 Hzto avoid malfunction and damage.

Tools needed

During assembly, installation and adjustment of the

opener, instructions will call for hand tools as illustrated below.

Pencil

Level (Optional)

 

 

Hack Saw

 

Tape

Measure

 

 

 

 

 

Wire Cutters

Drill

3/16",

5/16" and

Claw Hammer

 

 

 

5/32"

Drill Bits

 

Stepladder

Screwdriver

 

Adjustable End Wrench

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Abridor DE Puerta DE Cochera DE 315MN= Introduction ContentsPreparing your garage door Tools neededFinished Ceiling Sectional Door InstallationSectional Door Installations PlanningFinished Ceung ONE-PIECE Door InstallationsONE-PIECE Door Without Track ONE-PIECE Door with TrackSECURITY+ Carton InventoryAssembly Hardware Installation HardwareHardware Inventory Assemble the Rail Assembly StepHardware Shown Actual Size Fasten the Rail to the Motor Unit Install the Trolley Installation Readand Followall Installationwarningsand InstructionsAttach the Rail Brackets Determine the Header Bracket Location Installation StepInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Attach the Rail to the Header Bracket Important Information about Safety Reversing Sensor Install The Protector SystemFloor installation Figure Installing the BracketsGarage door track installation preferred Wall installationRecommended Wire Routing Mounting and Wiring the Safety SensorsPosition the Opener Sectional Door or ONE-PIECE Door with TrackEngaged Released Fenshed Ceung Hardware Shown Actual Size Hang the OpenerInstall Door Control Permanent Wiring Connection Complete the Safety Reversing Sensor InstallationAligning the Safety Reversing Sensors Troubleshooting the Safety Reversing SensorsAttach the Emergency Release Rope and Handle Install the LightsSectional Doors Fasten the Door BracketONE-PIECEDOORS Sectional Doors only Connect Door Arm to TrolleyConnect the door arm to the trolley Adjustment procedures, FigureALL ONE-PIECE Doors Assemble the door arm, FigureIf door does not open at least 5 feet 1.5 m Adjustment StepAdjust the Travel Limits HOW and When to Adjust the LimitsTest the UP open force Adjust the ForceHOW and When to Adjust the Forces Test the Down close forceTest The Protector System Test the Safety Reversal SystemAdjust Important Safety CheckUsing Your Garage Door Opener OperationReadand Followall Warningsand Instructions Using the Wall.Mounted Door Control Light featureTo Open the Door Manually Once a Year Remote Control BatteryCare of Your Opener Once a MonthRefer to Adjustment , Adjust the Force Having a PROBLEM?Symptom Motor unit doesnt operate Symptom LED is not lit on door controlTo Erase All Codes From Motor Unit Memory To Add or Reprogram a Hand-held Remote ControlUsing the Learn Button Using the Premium Control Console ProgrammingTo change an existing, known PIN To Add Reprogram Change Keyless Entry PINMust be programmed To operate Your Garage door Opener Entry is already mounted outside the garageNot Shown Repair PartsRail Assembly Parts Installation Parts KEY Part NO. NO. DescriptionMotor Unit Assembly Parts KEY PartKEY Part NO. NO.DESCRIPTION For Sectional Doors Only AccessoriesWarranty ServiceIntroduccion ContenidoHerramientas necesarias Preparaci6n de la puerta de su cocheraTecho TERMI/ADO Planificaci6nInstalacicn CON UNA Puerta Seccional Instalacion EN UNA Puerta SeccionalPuerta DE UNA Pieza CON Carril Planificaci6n continbaInstalacion CON Puertas DE UNA Sola Pieza Puerta DE UNA Sola Pieza SIN CarrilInventario de las caja de cart6n Tornillera Y Piezas Para EL Montaje Inventario de PiezasMonte el riel Montaje PasoEstas Piezas SE Muestran EN SU Tamano Real Montaje el riel continbaEstas Piezas SE Muestran EN SU Tamaiio Real Fije el riel a la unidad del motor e instale el troleFijacibn de las mnsulas del riel LA MuerteEltecho Instalacion PasoDetermine dbnde va a instalar la Mnsula del Cabezal CabezalInstalacion DE LA Mensula DEL Cabezal EN EL Instale la mnsula del cabezalEstas Piezas SE Muestran EN SU Tamaiio Real Colocacibn del riel en la mnsula del cabezalEnfrentando la puerta desde el lado interno del garaje Instale la Sistema de Protecci6nMontajeparedlado Derecho Instalacion DE LAS McnsulasInstalaci6n en la pared Figura 2 y Instalaci6n en el piso FiguraRuta recomendada para el cableado Coloque el Abridor en Posici6n Puerta DE UNA Sola Pieza SIN RielEnganchado Desenganchado Cuelgue el Abridor INSTALACION, PasoInstale la unidad de control de la puerta Estas Piezas SE Muestran EN SU Tamaio RealQuitar Y Volvera Ponerlatapa COMe Alinear LOS Sensores DE Seguridad Requisitos para la instalaci6n el6ctricaColoque la Cuerda y la Manija De Emergencia Instale las LucesPuertas Seccionales Fije la mnsula de la puertaPuertas DE UNA Sola Pieza SLO Para Puertas Seccionales Conecte el brazo de la puerta al troleArme el brazo de la puerta, Figura Todas LAS Puertas DE UNA Sola PiezaAjustes Paso Ajuste el limite del recorrido Hacia Arriba y Hacia AbajoCalcomanade Ajustes Etiouetade Ajustede Fuerza Ajuste de la fuerzaAjuste Pruebe la Sistema de Protecci6nPruebe el Sistema de Retroceso de Seguridad PruebaActive su abridor de alguna de las siguientes maneras ConserveestasinstruccionesOperacion C6mo Usar su Abridor de Puerta de CocheraCMO Reconectar EL Trole C6mo usar la unidad de control de paredC6mo abrir la puerta manualmente Como Desconectar EL TroleAjustes DE Lmite Y Fuerza Mantenimiento DE SU Abridor DE Puerta DE CocheraEl control remoto no activa la puerta SI Tiene Algon ProblemaEl motor Tabla de DiagComo Programar EL Abridor C6mo Agregar o Reprogramar un Control Remoto ManualControles Remotos de 3 Funciones Para cambiar un PIN existente Riel de 2.4 m 8 pies AccesoriosNo.,a,,erw.orna1,,noe.,a,,erw.so,1

139.53993D specifications

The Craftsman 139.53993D is a top-tier garage door opener designed for efficiency, convenience, and durability. This model is part of Craftsman's renowned lineup, known for reliable home improvement products. With its advanced features and technology, this garage door opener offers users a blend of functionality and modern convenience.

One of the standout features of the Craftsman 139.53993D is its powerful motor. Equipped with a robust 1/2 horsepower motor, it delivers strong lifting power, making it suitable for handling standard residential garage doors with ease. This strength ensures a smooth and reliable operation, even for heavier doors.

The technology integrated into the Craftsman 139.53993D significantly enhances security. This model utilizes a rolling code technology that changes the code each time the remote is used, making it nearly impossible for intruders to gain access. The safety features extend to the presence of an infrared safety sensor, which detects any obstacles in the door’s path and reverses its direction, preventing accidents and injuries.

Convenience is a key characteristic of this garage door opener. The Craftsman 139.53993D is compatible with various remote controls, including a keypad entry, allowing for keyless entry. Additionally, the model includes an integrated Wi-Fi capability. This feature grants homeowners remote access via a mobile app, enabling them to monitor and control their garage door from anywhere, adding an extra layer of convenience.

Installation is user-friendly owing to its clear instructions and included components. Most users can set it up in a short timeframe without professional help. Furthermore, the design of the motor unit is compact, allowing for easy placement and ensuring that it does not take up excessive space in the garage.

Alongside its functionality, the Craftsman 139.53993D is built with durability in mind. It features all-steel construction, providing long-lasting reliability and strength, suitable for the demands of daily use. The quiet operation is another impressive feature, ensuring that the door opens and closes smoothly without causing disturbances.

In summary, the Craftsman 139.53993D garage door opener stands out with its powerful motor, advanced security features, convenient technology, and robust construction. It reflects Craftsman's commitment to quality and innovation in home improvement solutions, making it a dependable choice for homeowners seeking a reliable garage door opener.
Top Page Image Contents