KitchenAid 8573755 A, 528879 Option 2 Install custom door panels on some models

Page 13

Option 2: Install custom door panels (on some models)

2. On the front side of the custom door panel, measure and

mark the location of the customer supplied handle. The

location is customer preference. Do not install handle at this

Custom door panel dimensions

9"

(22.9 cm)

medallion

location area

Top panel

(front view)

23⁷⁄₁₆" (59.5 cm)

9"

(22.9 cm)

medallion

location area

Bottom panel

(front view)

2⁵⁄₁₆"

(5.9 cm)

15⁵⁄₈"

(39.7 cm)

5"

(12.7 cm)

2¹⁄₈"

(5.4 cm)

14"

(35.6 cm)

5"

(12.7 cm)

 

time.

3.

On the front side of the custom door panel, measure, mark

 

and cut a hole for the medallion per specifications shown.

 

NOTE: The medallion must be placed within the specified

 

medallion area. Do not locate outside of this specified area.

4.

Lay the custom front panel face down on a protective

 

covering to prevent damage or abrasions.

5.

On the back side of the custom door panel, rout a ¹⁄₄"

 

(6.4 mm) radius around the medallion cutout. The medallion

 

end does not need to be routed.

6.

Measure and mark the vertical centerline and horizontal

 

position line on the back of the custom door panel.

 

 

mark

Top panel

horizontal line

1⁷⁄₁₆" (36.5 mm)

 

Bottom panel

mark

1³⁄₁₆" (30.2 mm)

centerline

 

7.Mount the handle to the custom door panel. The screws must not extend beyond the back surface of the panel. Countersink the holes.

8.Feed the wires of the medallion connector through the front of the custom door panel and push the medallion into the prepared medallion hole.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

23⁷⁄₁₆" (59.5 cm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

end may be round or

 

 

 

 

 

 

 

 

 

1⁹⁄₃₂"

 

squared off

 

1⁷⁄₃₂"

 

 

 

(32.6 mm)

 

 

 

 

 

 

 

 

 

 

 

max.

 

 

 

 

 

 

 

 

(30.8 mm)

 

 

 

 

1/4"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(6.4 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: Do not cut

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

beyond outline of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

medallion cutout.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Rout a ¹⁄₄" (6.4 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

radius around the back

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1¹³⁄₆₄"

 

side of the medallion

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(30.6 mm)

 

cutout.

 

 

 

 

 

 

 

2¹³⁄₃₂"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

It is not necessary to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(60.8 mm)

 

 

 

 

 

 

 

rout the ¹⁄₄" (6.4 mm)

 

 

 

 

 

 

 

 

 

Medallion cutout

 

radius on the right hand

 

 

 

 

 

 

 

 

 

 

tip of the medallion

 

 

 

 

 

 

 

 

 

 

(front of panel)

 

cutout.

 

 

 

 

 

 

 

 

 

 

 

 

 

Upper and lower panel minimum thickness is ⁵⁄₈" (16 mm). Panel thickness more than ¹¹⁄₁₆" (18 mm) can be accommodated but overall product depth will increase accordingly.

Custom door panel material must be suitable for damp conditions or adequately sealed to withstand moisture and humidity. Using a moisture-resistant material can provide additional protection. Taping edges alone may not provide adequate sealing. For painted panel, paint all rear edges to improve sealing.

1.Cut the custom door panel to specifications shown. The custom panel may be wider than the dishwasher in order to match the surrounding cabinets.

9.Remove the pins on both sides of the dishwasher drawer by pulling the pins straight out with a pair of needle-nose pliers.

pin

10.Gently pull the bottom of the metal plate away from the dishwasher, and then pull down.

11.Lay the custom door panel face down.

13

Image 13
Contents 528879/8573755 a Installation Instructions Drawer DishwasherTable of Contents Drawer Dishwasher SafetyProduct dimensions Installation RequirementsTools and Parts Location RequirementsWater Supply Requirements Cabinet dimensions/requirementsElectrical Requirements For a grounded, cord-connected dishwasherOption 1 Power Supply Cord Method Installation InstructionsPrepare Cabinet Opening Electrical ConnectionRemove factory-installed power cord Option 2 Direct Wiring MethodRemove the house wiring knockout Install Dishwasher If Installing Flexible Trim PiecesSlide the left-hand runner back into the dishwasher Choose attachment optionOption 1 Side attachment Option 2 Top attachmentOption 2 Garbage disposal connection Install the Drain HoseOption 1 Sink drain waste tee connection Option 1 Install standard door panels on some models Install Drawer Door Panels and Toe PanelConnect to Water Supply Option 3 Air break connectionBottom edge of the toe panel Option 1 Install standard toe panelFloor If not, remove the toe panel and shortenCustom door panel dimensions Option 2 Install custom door panels on some modelsCustom toe panel dimensions Option 2 Install custom toe panel on some modelsConnect the medallion connector to the dishwasher Connector Repeat steps 2-15 for other custom door panelIf dishwasher does not operate, check the following Complete Installation528879/8573755 Rev. a 528879/8573755A Instructions d’installation Lave-vaisselle tiroirTable des matières Sécurité DU LAVE-VAISSELLE TiroirEmplacement d’installation Exigences DinstallationOutillage et pièces Spécifications électriques Spécifications de l’alimentation en eauPour un lave-vaisselle branché en permanence Préparation de la cavité d’installation Instructions DinstallationMéthode recommandée de liaison à la terre Raccordement électriqueOption 2 Méthode par câblage direct Enlever le cordon d’alimentation installé à l’usineAvertissement Installation du lave-vaisselle Cas de linstallation de moulures Extrudées flexibles’arrière Options de fixationOption 1 Fixation latérale Raccordement à la canalisation dévacuation LinstallationOption 2 Fixation supérieure Option 2 Connexion sur le broyeur à déchets Raccordement à la source dalimentation en eauOption 3 Connexion au brise-siphon Panneau Avant inférieur Éliminer les bavures sur l’arête de Option 1 Installation de la planche de plinthe standardDimensions des panneaux avant personnalisés Placer le panneau avant personnalisé face vers le bas Dimensions de la planche de plinthe personnalisée528879/88573755 Rév. a Achever l’installation

528879, 8573755 A specifications

The KitchenAid 8573755 A,528879 is a versatile and powerful appliance designed to elevate the culinary experience in any kitchen. With its robust performance and innovative technologies, it caters to both amateur cooks and seasoned chefs alike.

One of the standout features of the KitchenAid 8573755 is its powerful motor, engineered for heavy-duty tasks. This ensures that the appliance can easily handle tough mixing and kneading, making it ideal for bread dough and other thick mixtures. The direct drive transmission allows for consistent performance, ensuring that users can achieve their desired results with minimal effort.

Incorporating advanced planetary mixing action, the KitchenAid 8573755 rotates the bowl in one direction while the beater rotates in the opposite direction. This unique feature ensures thorough mixing and even incorporation of ingredients, significantly reducing preparation time. Home cooks will appreciate how quickly and efficiently tasks such as whipping cream or mixing batter can be completed.

The KitchenAid 8573755 also comes with a variety of attachments, increasing its versatility. From a dough hook to a flat beater and wire whip, these accessories expand the kitchen's functionality, allowing users to whip, beat, knead, and mix with ease. Additionally, the compatibility with a wide range of optional attachments, such as pasta makers and food grinders, transforms the appliance into a multifunctional tool that can accommodate numerous culinary tasks.

Aesthetically, the KitchenAid 8573755 boasts a classic and timeless design that fits seamlessly into any kitchen decor. Its robust construction ensures durability, while the smooth surface makes cleaning a breeze. The appliance is also equipped with a tilt-head design, making it easy to access the bowl and add ingredients without hassle.

Safety is also a priority with the KitchenAid 8573755, featuring a power hub that allows for easy attachment of various tools and minimizing any risk during operation.

In summary, the KitchenAid 8573755 A,528879 combines power, versatility, and elegance, making it a must-have for anyone looking to enhance their cooking experience. With its robust features, advanced technologies, and focus on user convenience, this appliance stands out as a reliable companion in the kitchen.