Maytag 8101P641-60 Prepare The Venting Blower, Before You Start, Remove The Mounting Plate

Page 11

STEP 3: Prepare The Venting Blower

W A R N I N G

To avoid risk of property damage, unplug the microwave oven or disconnect power at source by removing fuse or throwing circuit breaker.

To avoid risk of personal injury, wear protective gloves when handling mounting plate.

DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in electrical shock.

Your microwave oven is shipped with the blower assembled for room venting. If you want wall-venting or roof-vented installation, you must change the blower, as detailed below.

Before You Start

1.Remove any shipping materials and parts from inside the microwave oven.

2.Cover the counter top or cooktop with a thick, protective covering to protect it from damage and dirt. See Figure 10.

NOTE: If you have a free-standing range, disconnect it, move it onto a piece of cardboard or hardboard and pull it away from the wall, so that you can get closer to the upper cabinet and back wall for easier measuring and drilling.

Remove The Mounting Plate:

1.Remove mounting plate screw(s) (1 or 2 screws) from the mounting plate as shown and discard. See Figure 11.

2.This plate will be used as the rear mounting plate. (It will be used to locate and mark the mounting holes on the rear wall.)

3.Locate exhaust adaptor, grease filters and hardware packet.

4.At this point, remove any adhesive tape (if there is any), on the exhaust adaptor, the grease filters and the power supply cord.

Room-Vented (recirculating) Installation:

This oven is shipped assembled for room-vented.

Wall-Vented Installation:

1.Remove one blower unit mounting screw and one or two blower plate screw(s). Remove the blower plate from cabinet. See Figure 12.

2.Carefully lift the blower unit out of the microwave oven.

3.Use side cutters or thin snips to cut and remove knockouts “B” from Back plate. Discard knockouts. Be careful not to distort the plate. See Figure 13.

A thick, protective

covering

Figure 10

Mounting plate

Mounting plate screw(s)

(1 or 2 screws)

Control Panel Side

Mounting plate

Mounting plate screw(s)

(1 or 2 screws)

Control Panel Side

Figure 11

Blower Plate

Mounting Screw

Blower Plate

Back Plate

Blower Unit

Blower Unit

Mounting Screw

Parts “B” Figure 12

Knockouts Parts “B”

Parts “B”

Figure 13

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Electric Microwave ContentsPage Recognize this symbol as a Safety message Important Safety InformationOven Must be grounded. Grounding reduces Grounding InstructionsMake Sure You Have Enough Space And Support Parts, Tools, Materials Damper/duct connectorParts, Tools, Materials R N I N G Prepare The Electrical ConnectionRoom Venting Prepare The Venting SystemR N I N G F I R E H a Z a R D Wall Venting Roof Venting73 ft Standard Fittings Duct LengthBefore You Start Room-Vented recirculating InstallationWall-Vented Installation Prepare The Venting BlowerPorts Roof-Vented InstallationMeasure And Track/Tape Up The Templates Prepare The Wall & Upper CabinetDrill The Holes In The Wall And Upper Cabinet Oven Must Be Connected To At Least One Wall Stud Install The Mounting PlateFor Wall-Vented Attach The Oven To The Wall Attach The Oven To The Wall Contenido Microondas eléctricoConserve Estas Instrucciones Reconozca este símbolo como un mensaje de Seguridad Información Importante DE SeguridadInstrucciones para la Puesta a Tierra Asegúrese de tener suficiente espacio y ayuda Dos tornillos para madera autorroscantes Un gabarit pour le mur arrière Dimensions réduitesPuerta de tiro invertido, conector del ducto Cuatro pernos acodillados de 1/4 x 3 Tamaño realPiezas, herramientas, materiales Tomacorriente Conectado a tierra Paso 1 Preparación de la conexiones eléctricasV E R T E N C I a SuperiorVentilación hacia la habitación Paso 2 Preparación del sistema de ventilaciónVentilación por el techo Ventilación por la pared= 73pies 22m Accesorios estándarLongitud del ducto Instalación de ventilación ambiente recirculación Paso 3 Preparación del ventiladorAntes de comenzar Retire la placa de montajeFigura 15 escape Instalación de ventilación en techoMida las plantillas y márquelas con cinta métrica Paso 4 Preparación de los gabinetes de pared y superiorGabarit Pour MUR Arrière Taladre los orificios en la pared y en el gabinete superiorEl horno debe estar fijado a un travesaño como mínimo Paso 5 Instalación de la placa de montajePara ventilación en pared Paso 6 Sujeción del horno a la pared Ducto Table des matières Électrique à micro-ondesConserver CES Instructions Consignes DE Sécurité Importantes Ce symbole signale un message de SécuritéNe pas utiliser de rallonge électrique Instructions de liaison à la terreUtiliser le gabarit inclus avec la notice de mise en service Quatre tire-fonds de 1/4 x 2 po6 x 51 mm Clapet de refoulement / raccord de conduitUn serre-câble et Une vis de couleur foncée Une traversée pour serre-câble Grandeur réelleIl faut les outils et matériaux suivants Trou pour le cordon d’alimentation Étape 1 Préparer le raccordement à l’électricitéE R T I S S E M E N T Armoire Supérieure Prise reliée à la TerreÉvacuation dans la pièce Étape 2 Préparer l’évacuationÉvacuation par le mur Évacuation par le toit Longueur de conduit Matériel standardÉvacuation dans la pièce recirculation de l’air Étape 3 Préparer le ventilateur d’évacuationAvant de commencer Retirer la plaque de montageÉvacuation par le toit Étape 4 Préparer le mur et l’armoire supérieure Plantilla DE LA Pared Posterior Le four doit être fixé à au moins un montant de mur Étape 5 Poser la plaque de montagePlaque de montage Plaque d’une pièce Étape 6 Fixer le four au mur Évacuation par le toit Poser le conduit d’évacuation dans

8101P641-60 specifications

The Maytag 8101P641-60 is a highly regarded product in the realm of laundry appliances, known for its dependability and performance. This model exemplifies the strength and efficiency for which Maytag has long been recognized.

One standout feature of the Maytag 8101P641-60 is its robust construction. Built with durability in mind, it features a heavy-duty motor that ensures longevity, capable of handling even the largest laundry loads with ease. The model's high spin speeds effectively extract water from clothes, leading to shorter drying times and energy savings.

In terms of technology, the Maytag 8101P641-60 is equipped with advanced washing cycles that cater to a variety of fabric types and soil levels. The model includes an array of settings, such as delicate, normal, and heavy-duty, allowing users to customize their washing experience according to their needs. The direct drive motor further enhances the efficiency, providing reliable torque and minimizing noise, thus making laundry day a more pleasant experience.

Another noteworthy characteristic is the energy-efficient design. The Maytag 8101P641-60 is Energy Star certified, which means it meets strict energy efficiency guidelines. This not only contributes to lower utility bills but also promotes environmental sustainability.

The machine’s large capacity is designed to handle oversized loads, accommodating bulky items like comforters and blankets. Its user-friendly interface features intuitive controls, making it easy for anyone to navigate through the various washing programs.

Moreover, the appliance is noted for its seamless operation and minimal vibrations, ensuring a quieter experience than many competing models.

In summary, the Maytag 8101P641-60 represents a blend of power, efficiency, and convenience. With its durable construction, advanced washing technologies, energy efficiency, and user-friendly features, it stands out as a top choice for households in need of a reliable washing machine. Whether it’s tackling everyday laundry or special care tasks, this model delivers impressive performance that meets the demands of modern living.
Top Page Image Contents