Maytag 8101P641-60 installation instructions Drill The Holes In The Wall And Upper Cabinet

Page 14

STEP 4: Prepare The Wall & Upper Cabinet

W A R N I N G

To avoid risk of personal injury, electrical shock or death:

Note where electrical outlets and electrical wires are before you drill into the wall.

Locate and disconnect power to any electrical circuits that could be affected by installing this oven.

W A R N I N G

To avoid risk of personal injury, electrical shock or death, cover the edge of the power supply cord hole with the power supply cord bushing.

Drill The Holes In The Wall And Upper Cabinet.

1.Drill holes on the circles. If there is a stud, drill a 3/16" hole for lag screws. If there is no stud, drill a 3/4" hole for toggle screws. Make sure to use at least 1 lag screw in a stud, and 4 toggle screws in the drywall or the plaster.

2.Drill a 3/8” hole at points J and K on the upper cabinet template.

NOTE: If the bottom of the upper cabinet is recessed 3/4" or more, you will need 2"x 2" filler blocks (not included) to provide additional support for the bolts. See Figure 25.

Mark the center of each filler block and drill a 3/8” diameter hole at the marks.

Align filler blocks over the two openings in the top of the microwave oven cabinet and attach to cabinet with masking tape. See Figure 26.

3.Cut or drill a 2" diameter hole at the area marked M. Power supply cord hole on the upper cabinet template. If the upper cabinet is metal, you will need to cover the edge of the hole with the power supply cord bushing (supplied) to prevent damage to the cord from the rough metal edge.

4.Cut out the venting areas (with the saber saw):

Roof-Vented: cut out the shaded area marked L on the upper cabinet template.

Wall-Vented: Tape the rear wall template to the rear wall, lining up with the holes previously drilled for holes A and B in the plate. Cut out the shaded area marked F on the REAR WALL TEMPLATE.

Room-Vented: go to STEP 5, INSTALL THE MOUNTING PLATE, located on page 15.

5.Complete whichever venting system you have chosen. Use caulking compound to seal the exterior wall or roof opening around the wall cap or roof cap.

filler block

cabinet

cabinet front

bottom shelf

 

Figure 25

filler

block

Figure 26

14

Image 14
Contents Contents Electric MicrowavePage Important Safety Information Recognize this symbol as a Safety messageGrounding Instructions Oven Must be grounded. Grounding reducesMake Sure You Have Enough Space And Support Damper/duct connector Parts, Tools, MaterialsParts, Tools, Materials Prepare The Electrical Connection R N I N GWall Venting Roof Venting Prepare The Venting SystemR N I N G F I R E H a Z a R D Room VentingStandard Fittings Duct Length 73 ftPrepare The Venting Blower Room-Vented recirculating InstallationWall-Vented Installation Before You StartRoof-Vented Installation PortsPrepare The Wall & Upper Cabinet Measure And Track/Tape Up The TemplatesDrill The Holes In The Wall And Upper Cabinet Install The Mounting Plate Oven Must Be Connected To At Least One Wall StudFor Wall-Vented Attach The Oven To The Wall Attach The Oven To The Wall Microondas eléctrico ContenidoConserve Estas Instrucciones Información Importante DE Seguridad Reconozca este símbolo como un mensaje de SeguridadInstrucciones para la Puesta a Tierra Asegúrese de tener suficiente espacio y ayuda Cuatro pernos acodillados de 1/4 x 3 Tamaño real Un gabarit pour le mur arrière Dimensions réduitesPuerta de tiro invertido, conector del ducto Dos tornillos para madera autorroscantesPiezas, herramientas, materiales Superior Paso 1 Preparación de la conexiones eléctricasV E R T E N C I a Tomacorriente Conectado a tierraVentilación por la pared Paso 2 Preparación del sistema de ventilaciónVentilación por el techo Ventilación hacia la habitación= 73pies 22m Accesorios estándarLongitud del ducto Retire la placa de montaje Paso 3 Preparación del ventiladorAntes de comenzar Instalación de ventilación ambiente recirculaciónInstalación de ventilación en techo Figura 15 escapePaso 4 Preparación de los gabinetes de pared y superior Mida las plantillas y márquelas con cinta métricaTaladre los orificios en la pared y en el gabinete superior Gabarit Pour MUR ArrièrePaso 5 Instalación de la placa de montaje El horno debe estar fijado a un travesaño como mínimoPara ventilación en pared Paso 6 Sujeción del horno a la pared Ducto Électrique à micro-ondes Table des matièresConserver CES Instructions Ce symbole signale un message de Sécurité Consignes DE Sécurité ImportantesInstructions de liaison à la terre Ne pas utiliser de rallonge électriqueUtiliser le gabarit inclus avec la notice de mise en service Une traversée pour serre-câble Grandeur réelle Clapet de refoulement / raccord de conduitUn serre-câble et Une vis de couleur foncée Quatre tire-fonds de 1/4 x 2 po6 x 51 mmIl faut les outils et matériaux suivants Armoire Supérieure Prise reliée à la Terre Étape 1 Préparer le raccordement à l’électricitéE R T I S S E M E N T Trou pour le cordon d’alimentationÉvacuation dans la pièce Étape 2 Préparer l’évacuationÉvacuation par le mur Évacuation par le toit Matériel standard Longueur de conduitRetirer la plaque de montage Étape 3 Préparer le ventilateur d’évacuationAvant de commencer Évacuation dans la pièce recirculation de l’airÉvacuation par le toit Étape 4 Préparer le mur et l’armoire supérieure Plantilla DE LA Pared Posterior Étape 5 Poser la plaque de montage Le four doit être fixé à au moins un montant de murPlaque de montage Plaque d’une pièce Étape 6 Fixer le four au mur Évacuation par le toit Poser le conduit d’évacuation dans

8101P641-60 specifications

The Maytag 8101P641-60 is a highly regarded product in the realm of laundry appliances, known for its dependability and performance. This model exemplifies the strength and efficiency for which Maytag has long been recognized.

One standout feature of the Maytag 8101P641-60 is its robust construction. Built with durability in mind, it features a heavy-duty motor that ensures longevity, capable of handling even the largest laundry loads with ease. The model's high spin speeds effectively extract water from clothes, leading to shorter drying times and energy savings.

In terms of technology, the Maytag 8101P641-60 is equipped with advanced washing cycles that cater to a variety of fabric types and soil levels. The model includes an array of settings, such as delicate, normal, and heavy-duty, allowing users to customize their washing experience according to their needs. The direct drive motor further enhances the efficiency, providing reliable torque and minimizing noise, thus making laundry day a more pleasant experience.

Another noteworthy characteristic is the energy-efficient design. The Maytag 8101P641-60 is Energy Star certified, which means it meets strict energy efficiency guidelines. This not only contributes to lower utility bills but also promotes environmental sustainability.

The machine’s large capacity is designed to handle oversized loads, accommodating bulky items like comforters and blankets. Its user-friendly interface features intuitive controls, making it easy for anyone to navigate through the various washing programs.

Moreover, the appliance is noted for its seamless operation and minimal vibrations, ensuring a quieter experience than many competing models.

In summary, the Maytag 8101P641-60 represents a blend of power, efficiency, and convenience. With its durable construction, advanced washing technologies, energy efficiency, and user-friendly features, it stands out as a top choice for households in need of a reliable washing machine. Whether it’s tackling everyday laundry or special care tasks, this model delivers impressive performance that meets the demands of modern living.