Maytag 8101P641-60 Install The Mounting Plate, Oven Must Be Connected To At Least One Wall Stud

Page 15

STEP 5: Install The Mounting Plate

The Oven Must Be Connected To At Least One

Wall Stud.

1.Draw a vertical line on the wall at the center of the 30 wide space. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are against the bottom of the cabinet. Line up the notch and center line on the mounting plate to the center line on the wall.

2.While holding the mounting plate with one hand, draw circles on the wall at holes A, B, C and D. Four holes must be used for mounting. If the holes are not used, the installation will not be secure. Installer must use these holes for proper installation. Use toggle bolts through these holes unless one of them lines up with a stud. Use a wood screw for studs.

NOTE: Draw a fifth circle inside area E, through one of the bottom holes to match the location of a stud. For wall- vented: The oven requires a rear wall cutout opening for the rear wall duct and the exhaust adaptor must be attached to the mounting plate. See the next page on how to prepare the rear wall cutout opening and the exhaust adaptor/mounting plate for wall-vented.

3. Drill holes on the circles. If there is a stud, drill a 3/16 hole

Minimum 66"

From the Floor

Mounting

Plate

A

CCenter Line

3/16 Hole on Studs 5/8 Hole on Dry wall Only

For Wall-

Vented Only

Draw Lines on Studs

Draw

Center Line

B

D

E

for lag screws. If there is no stud, drill a 5/8 hole for toggle

bolts. Make sure to use at least 1 lag screw in a stud, and

4 toggle bolts in the drywall or the plaster.

4. Attach the plate to the wall. To use spring toggle head

bolts: Remove the toggle wings from the bolts. Insert the

bolts into the mounting plate and replace the spring toggle

head to 3/4 past the bolt ends. Insert the spring toggle

head into the holes in the wall to mount the plate. You may

pull forward on the plate to help in tightening the toggle

bolts. Tighten all bolts.

 

 

 

 

 

Space More Than Wall Thickness

 

 

 

 

 

Toggle Wings

 

 

 

Mounting

 

 

 

 

 

 

 

 

 

 

Plate

 

 

 

 

Toggle Bolt

 

 

 

 

 

 

 

 

Bolt

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

End

 

 

 

 

 

Wall

 

 

 

 

 

Figure 28

Support Tab

Support Tab

(1 piece mounting plate)

3/16 Hole on Studs 5/8 Hole on Dry wall Only

Minimum 66"

From the Floor For Wall-

Vented Only

 

Draw Lines

 

 

on Studs

 

 

Draw

 

 

Center Line

B

A

 

 

 

 

Mounting

 

 

Plate

 

C Center Line

 

D

 

 

 

E

 

Support Tab

Support Tab

(3 pieces mounting plate)

Figure 27

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Electric Microwave ContentsPage Recognize this symbol as a Safety message Important Safety InformationOven Must be grounded. Grounding reduces Grounding InstructionsMake Sure You Have Enough Space And Support Parts, Tools, Materials Damper/duct connectorParts, Tools, Materials R N I N G Prepare The Electrical ConnectionRoom Venting Prepare The Venting SystemR N I N G F I R E H a Z a R D Wall Venting Roof Venting73 ft Standard Fittings Duct LengthBefore You Start Room-Vented recirculating InstallationWall-Vented Installation Prepare The Venting BlowerPorts Roof-Vented InstallationMeasure And Track/Tape Up The Templates Prepare The Wall & Upper CabinetDrill The Holes In The Wall And Upper Cabinet Oven Must Be Connected To At Least One Wall Stud Install The Mounting PlateFor Wall-Vented Attach The Oven To The Wall Attach The Oven To The Wall Contenido Microondas eléctricoConserve Estas Instrucciones Reconozca este símbolo como un mensaje de Seguridad Información Importante DE SeguridadInstrucciones para la Puesta a Tierra Asegúrese de tener suficiente espacio y ayuda Dos tornillos para madera autorroscantes Un gabarit pour le mur arrière Dimensions réduitesPuerta de tiro invertido, conector del ducto Cuatro pernos acodillados de 1/4 x 3 Tamaño realPiezas, herramientas, materiales Tomacorriente Conectado a tierra Paso 1 Preparación de la conexiones eléctricasV E R T E N C I a SuperiorVentilación hacia la habitación Paso 2 Preparación del sistema de ventilaciónVentilación por el techo Ventilación por la paredAccesorios estándar Longitud del ducto= 73pies 22m Instalación de ventilación ambiente recirculación Paso 3 Preparación del ventiladorAntes de comenzar Retire la placa de montajeFigura 15 escape Instalación de ventilación en techoMida las plantillas y márquelas con cinta métrica Paso 4 Preparación de los gabinetes de pared y superiorGabarit Pour MUR Arrière Taladre los orificios en la pared y en el gabinete superiorEl horno debe estar fijado a un travesaño como mínimo Paso 5 Instalación de la placa de montajePara ventilación en pared Paso 6 Sujeción del horno a la pared Ducto Table des matières Électrique à micro-ondesConserver CES Instructions Consignes DE Sécurité Importantes Ce symbole signale un message de SécuritéNe pas utiliser de rallonge électrique Instructions de liaison à la terreUtiliser le gabarit inclus avec la notice de mise en service Quatre tire-fonds de 1/4 x 2 po6 x 51 mm Clapet de refoulement / raccord de conduitUn serre-câble et Une vis de couleur foncée Une traversée pour serre-câble Grandeur réelleIl faut les outils et matériaux suivants Trou pour le cordon d’alimentation Étape 1 Préparer le raccordement à l’électricitéE R T I S S E M E N T Armoire Supérieure Prise reliée à la TerreÉtape 2 Préparer l’évacuation Évacuation par le mur Évacuation par le toitÉvacuation dans la pièce Longueur de conduit Matériel standardÉvacuation dans la pièce recirculation de l’air Étape 3 Préparer le ventilateur d’évacuationAvant de commencer Retirer la plaque de montageÉvacuation par le toit Étape 4 Préparer le mur et l’armoire supérieure Plantilla DE LA Pared Posterior Le four doit être fixé à au moins un montant de mur Étape 5 Poser la plaque de montagePlaque de montage Plaque d’une pièce Étape 6 Fixer le four au mur Évacuation par le toit Poser le conduit d’évacuation dans

8101P641-60 specifications

The Maytag 8101P641-60 is a highly regarded product in the realm of laundry appliances, known for its dependability and performance. This model exemplifies the strength and efficiency for which Maytag has long been recognized.

One standout feature of the Maytag 8101P641-60 is its robust construction. Built with durability in mind, it features a heavy-duty motor that ensures longevity, capable of handling even the largest laundry loads with ease. The model's high spin speeds effectively extract water from clothes, leading to shorter drying times and energy savings.

In terms of technology, the Maytag 8101P641-60 is equipped with advanced washing cycles that cater to a variety of fabric types and soil levels. The model includes an array of settings, such as delicate, normal, and heavy-duty, allowing users to customize their washing experience according to their needs. The direct drive motor further enhances the efficiency, providing reliable torque and minimizing noise, thus making laundry day a more pleasant experience.

Another noteworthy characteristic is the energy-efficient design. The Maytag 8101P641-60 is Energy Star certified, which means it meets strict energy efficiency guidelines. This not only contributes to lower utility bills but also promotes environmental sustainability.

The machine’s large capacity is designed to handle oversized loads, accommodating bulky items like comforters and blankets. Its user-friendly interface features intuitive controls, making it easy for anyone to navigate through the various washing programs.

Moreover, the appliance is noted for its seamless operation and minimal vibrations, ensuring a quieter experience than many competing models.

In summary, the Maytag 8101P641-60 represents a blend of power, efficiency, and convenience. With its durable construction, advanced washing technologies, energy efficiency, and user-friendly features, it stands out as a top choice for households in need of a reliable washing machine. Whether it’s tackling everyday laundry or special care tasks, this model delivers impressive performance that meets the demands of modern living.
Top Page Image Contents