Hoshizaki KM-1300SAH-E, KM-1300SRH-E installation manual Operation, BIN Control Check

Page 10

ENGLISH

6)Check the water supply and drain connections for water leaks.

7)Turn off the power supply, and remove the Front Panel.

8)Remove the Insulation Panel. Remove the Cap located on the front bottom part of the Ice Dropping Hole. Drain the Water Tank to flush any loose debris. See Fig. 12.

BIN CONTROL CHECK

1)With the Front Panel in place, remove the thumb- screws along the upper edge of the storage bin ice deflector and allow it to pivot on the side fixings.

2)Hold some ice against the Bin Control Bulb. The icemaker should stop within 6 to 10 seconds.

3)Replace the thumbscrews and close the bin door.

4)Check that the icemaker re-starts.

Fig. 12

9)Replace the Cap, Insulation Panel and Front Panel in their correct positions.

10)Clean the Storage Bin.

11)Turn on the power supply, and start the automatic icemaking process.

12)Wait until a complete icemaking and defrost cycle is completed.

10. OPERATION

The steps in the sequence are as follows:

1) 1 Minute Fill Cycle

The unit always starts in the 1 minute fill cycle. When power is applied to the unit, the water valve is ener- gized and the fill period begins. After 1 minute the board checks for a closed float switch. If the float switch is closed the harvest cycle begins. If not, the unit will not start without adequate water in the sump. This serves a low water safety shut off. The water valve will remain energized through additional 1 minute cycles until water enters the sump and the float switch closes.

2) 1st Harvest Cycle

The compressor starts, hot gas valve opens, water valve remains open and harvest begins. As the evaporator warms, the thermistor located on the suction line checks for a 9°C temperature. When 9°C is reached, the harvest is turned over to the adjust- able control board defrost timer which is factory set for normal conditions. This adjustment can vary the defrost timer from 1 to 3 minutes.

3) Freeze Cycle

After the timer terminates the harvest cycle, the hot gas and water valves close, and the ice production cycle starts. For the first 5 minutes the controller board will not accept a signal from the float switch. This 5 minute minimum freeze acts as a short cycle protection. At the end of 5 minutes the float switch assumes control. As ice builds on the evaporator the water level in the sump lowers. The freeze continues until the float switch opens and terminates ice pro- duction.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents KM-1300SAH-E KM-1300SRH-E HOW to Remove Panels See Fig UnpackingInstallation LocationStacking TWO Icemakers SeeLocation Electrical ConnectionUnpacking This Appliance Must be EarthedInstallation Electrical Connection See Fig Stacking the Condenser UnitWater Supply and Drain Connections Start UP KM-1300SAH-E KM-1300SRH-EOperation BIN Control CheckFinal Check List Have all electrical and piping connections been made?Achtung AuspackenAbnahme DER Platten Siehe Abbildung VorsichtAbb StandortAbb a Stapeln VON Zwei Eismaschinen Siehe Bild 4 Abb bAuspacken StromanschlussAufstellung Installation Stromanschluss Dieses Gerät Muss Geerdet WerdenWASSER- UND ABWASSER- Anschlüsse Vgl. Abb Stapeln VON KondensatorenWarnung KM-1300SAH-E KM-1300SRH-E Abb II. Einschalten Prüfung DER Behälterfüllstandsregelung BetriebCheckliste FÜR DIE Endüberprüfung Cómo Retirar LOS Paneles DesembaladoVea la figura Instalación UbicaciónPrecaución Apilamiento DE DOS Dispensadores DE Hielo Ver figuras 4 yDesembalaje Conexión EléctricaAdvertencia Este Aparato SE Debe Conectar a Tierra UbicaciónInstalación Conexión Eléctrica Precaución Este Aparato Debe Estar Conectado a TierraConexiones DE Suministro DE Agua Y DESAGÜE- Vea la figura Apilamiento DE LA Unidad DE CondensaciónKM-1300SAH-E KM-1300SRH-E Arranque Inicial Operación Comprobación DEL Control DEL Recipiente DE AlmacenamientoLista Final DE Comprobación LE Demontage DES Panneaux Voir Figure DeballageAvertissement Emplacement Empilage DE Deux Distributeurs L’UN SUR L’AUTRE VoirAvertissement CET Appareil Doit Etre MIS a LA Terre EmplacementRaccordements Electriques DeballageInstallation Raccordements Electriques Raccordements DE L’ARRIVEE Empilage DU Condenseur’EAU ET DE LA Vidange Voir Figure KM-1300SAH-E KM-1300SRH-E Mise EN Route Verification DE LA Commande DE Reservoir FonctionnementCheck List Finale Avvertenza DisimballaggioRimozione DEI Pannelli V. FIG AttenzioneInstallazione UbicazioneSovrapposizione Delle DUE Cubettatrici V. e Disimballaggio Collegamenti ElettriciAvvertenza Collegare IL Distributore a UNA Presa DI Terra PosizioneInstallazione Collegamenti Elettrici Sovrapposizione DEL Condensatore Collegamenti PER Alimentazione E Scarico AcquaAvviamento Funzionamento Controllo Della Funzionalità Della VaschettaControlli finali Belangrijk UitpakkenHET Verwijderen VAN DE Panelen Zie Afb WaarschuwingLocatie InstallatieAfb a Zie HET Stapelen VAN Twee IjsdispensersAfb b Uitpakken Elektrische AansluitingenPlaatsen Installatie Hoshizaki EuropeElektrische Aansluitingen HET Stapelen VAN DE Condensor Afb Aansluitingen Voor Watertoevoer EN -AFVOER Zie AfbAfb Opstarten Controle VAN DE BAK WerkingEindcontrole

KM-1300SRH-E, KM-1300SAH-E specifications

The Hoshizaki KM-1300SAH-E and KM-1300SRH-E are part of Hoshizaki's renowned line of ice makers, known for their reliability, efficiency, and high-quality ice production. These models are particularly well-suited for busy environments such as restaurants, cafes, and hotels where on-demand ice is essential for both food service and customer satisfaction.

One of the standout features of the KM-1300SAH-E and KM-1300SRH-E is their impressive ice production capacity. They can produce up to 1,300 pounds of crescent-shaped ice per day, ensuring that businesses can keep up with high demand without compromising on quality. The crescent ice produced by these machines is ideal for a variety of applications, including beverages, food display, and ice for culinary purposes.

Both models are equipped with the latest Hoshizaki technology, which includes a powerful refrigeration system that enhances energy efficiency and cooling speed. This advanced technology not only helps in maintaining optimal ice-making temperatures but also reduces energy consumption, making these machines more eco-friendly and cost-effective over time.

Another significant aspect of the KM-1300 series is the user-friendly design. The machines feature a built-in storage bin that holds up to 1,002 pounds of ice, allowing for ample storage capacity to meet peak demands. The front access design ensures easy maintenance and cleaning, which is crucial for keeping the ice machine operating smoothly and hygienically.

The KM-1300SAH-E and KM-1300SRH-E are also designed with durability in mind. Constructed with stainless steel, they offer resistance against corrosion and wear, ensuring a long lifespan in demanding environments. Their robust design allows them to withstand the rigors of daily use in commercial settings.

In terms of safety features, Hoshizaki has integrated several technologies into these models. The cleaning and sanitizing cycles are automated, reducing the labor involved in maintaining sanitary conditions. Additionally, the ice machines are equipped with a self-diagnosis feature that alerts users to any potential issues, allowing for quick troubleshooting.

In conclusion, the Hoshizaki KM-1300SAH-E and KM-1300SRH-E ice machines exemplify the brand's commitment to quality, efficiency, and innovation. With their substantial ice production capabilities, advanced features, and ease of maintenance, these models are a smart investment for any commercial establishment that requires reliable ice-making solutions. Adopting these machines can significantly enhance operational efficiency while ensuring that customers receive the best service possible.
Top Page Image Contents