Hoshizaki KM-1300SAH-E Stapeln VON Kondensatoren, WASSER- UND ABWASSER- Anschlüsse Vgl. Abb

Page 18

DEUTSCH

Empfohlene Leitergröße 0,75mm2.

In der Regel ist eine Genehmigung für Elektroanlagen erforderlich, außerdem ist ein anerkannter Elektriker hinzuziehen.

1)Die vier Schrauben und die Platte vom Fernkondensator abmontieren.

2)Die zwei Schrauben und die Abdeckung der Anschlußdose vom Fernkondensator abmontieren.

3)Die Schraube und die Abdeckung der URC- Gebläsemotoranschlußdose von der Eismaschine abmontieren.

4)Die Leitungsdrähte des Gebläsemotors in der Anschlußdose des Fernkondensators an die Leitungsdrähte des Gebläsemotors in der Anschlußdose der fernluftgekühlten HOSHIZAKI- Eismaschine anschließen. Die Gebläsemotoren des URC-12F-E arbeiten mit 115-V- Wechselstrom. Den URC-12F-E daher nicht an das 230-V-WS-Hauptnetz anschließen.

5)Von der Eismaschine zum Fernkondensator eine Erdleitung installieren.

6)Platte und Abdeckung der Anschlußdose in ihrer ursprünglichen Position wieder anbringen.

[e] STAPELN VON KONDENSATOREN

1)Unteren Kondensator mit acht Schrauben an den Füßen befestigen.

2)Obere Platte des unteren Kondensators abnehmen.

3)Den oberen Kondensator auf den unteren stellen.

4)Den oberen Kondensator mit den Schrauben aus der oberen Platte des unteren Kondensators sichern.

5)Kühlmittelleitungen installieren und elektrische Anschlüsse für die einzelnen Gebläsemotoren vornehmen, wie unter [c] und [d] dargestellt.

Abb. 10

8.WASSER- UND ABWASSER- ANSCHLÜSSE – Vgl. Abb. 11

WARNUNG

Damit die Pumpe nicht beschädigt wird, darf die Eismaschine nicht betrieben werden, wenn das Wasser ABGESTELLT ist oder wenn der Druck unter 0,7 bar abfällt. Die Eismaschine erst wieder einschalten, wenn der korrekte Wasser- druck vorhanden ist.

Für diese Eismaschine darf nur Trinkwasser verwendet werden.

Die Maschine ist nur von einer qualifizierten Person an das Wasser anzuschließen.

Der Wasseranschluß hat ein Rohrinnengewinde ½”.

In der Wasserleitung sollten ein Absperr- und ein Ablaßventil installiert werden. Für das Absperrventil wird ein Kugelhahn empfohlen. Wenn ein anderes Ventil als ein Kugelhahn verwendet wird, sollte dessen Mindestöffnung nicht kleiner als der Innendurchmesser der Wasserleitung sein, da dies sonst zu einem verringerten Durchfluß führen kann, was wiederum zu einer schlechten Entfrostung und/oder Zufrieren führen kann. Für die Wasserleitung wird eine Kupferleitung mit einem Außendurchmesser von mindestens 13 mm empfohlen.

Der Wasserdruck sollte mindestens 0,7 bar und maximal 8 bar betragen. Wenn der Druck 8 bar überschreitet, ist ein Druckreduzierventil zu verwenden. Den Druck NICHT durch Zudrehen des Anschlußhahns verringern.

Der Abflußanschluß für die Eismaschine und den Vorratsbehälter hat ein Rohrinnengewinde ¾”. Der Kondensatablauf ist eine Leitung mit 10 mm Innendurchmesser. Der Abfluß der Eismaschine

18

Image 18
Contents KM-1300SAH-E KM-1300SRH-E HOW to Remove Panels See Fig UnpackingInstallation LocationStacking TWO Icemakers SeeLocation Electrical ConnectionUnpacking This Appliance Must be EarthedInstallation Electrical Connection Stacking the Condenser Unit See FigWater Supply and Drain Connections Start UP KM-1300SAH-E KM-1300SRH-EOperation BIN Control CheckFinal Check List Have all electrical and piping connections been made?Achtung AuspackenAbnahme DER Platten Siehe Abbildung VorsichtStandort AbbAbb a Stapeln VON Zwei Eismaschinen Siehe Bild 4 Abb bStromanschluss AuspackenAufstellung Installation Stromanschluss Dieses Gerät Muss Geerdet WerdenStapeln VON Kondensatoren WASSER- UND ABWASSER- Anschlüsse Vgl. AbbWarnung KM-1300SAH-E KM-1300SRH-E Abb II. Einschalten Prüfung DER Behälterfüllstandsregelung BetriebCheckliste FÜR DIE Endüberprüfung Desembalado Cómo Retirar LOS PanelesVea la figura Ubicación InstalaciónPrecaución Apilamiento DE DOS Dispensadores DE Hielo Ver figuras 4 yDesembalaje Conexión EléctricaAdvertencia Este Aparato SE Debe Conectar a Tierra UbicaciónInstalación Conexión Eléctrica Precaución Este Aparato Debe Estar Conectado a TierraConexiones DE Suministro DE Agua Y DESAGÜE- Vea la figura Apilamiento DE LA Unidad DE CondensaciónKM-1300SAH-E KM-1300SRH-E Arranque Inicial Operación Comprobación DEL Control DEL Recipiente DE AlmacenamientoLista Final DE Comprobación Deballage LE Demontage DES Panneaux Voir FigureAvertissement Emplacement Empilage DE Deux Distributeurs L’UN SUR L’AUTRE VoirAvertissement CET Appareil Doit Etre MIS a LA Terre EmplacementRaccordements Electriques DeballageInstallation Raccordements Electriques Empilage DU Condenseur Raccordements DE L’ARRIVEE’EAU ET DE LA Vidange Voir Figure KM-1300SAH-E KM-1300SRH-E Mise EN Route Verification DE LA Commande DE Reservoir FonctionnementCheck List Finale Avvertenza DisimballaggioRimozione DEI Pannelli V. FIG AttenzioneInstallazione UbicazioneSovrapposizione Delle DUE Cubettatrici V. e Disimballaggio Collegamenti ElettriciAvvertenza Collegare IL Distributore a UNA Presa DI Terra PosizioneInstallazione Collegamenti Elettrici Sovrapposizione DEL Condensatore Collegamenti PER Alimentazione E Scarico AcquaAvviamento Funzionamento Controllo Della Funzionalità Della VaschettaControlli finali Belangrijk UitpakkenHET Verwijderen VAN DE Panelen Zie Afb WaarschuwingInstallatie LocatieAfb a HET Stapelen VAN Twee Ijsdispensers ZieAfb b Elektrische Aansluitingen UitpakkenPlaatsen Installatie Hoshizaki EuropeElektrische Aansluitingen HET Stapelen VAN DE Condensor Afb Aansluitingen Voor Watertoevoer EN -AFVOER Zie AfbAfb Opstarten Controle VAN DE BAK WerkingEindcontrole

KM-1300SRH-E, KM-1300SAH-E specifications

The Hoshizaki KM-1300SAH-E and KM-1300SRH-E are part of Hoshizaki's renowned line of ice makers, known for their reliability, efficiency, and high-quality ice production. These models are particularly well-suited for busy environments such as restaurants, cafes, and hotels where on-demand ice is essential for both food service and customer satisfaction.

One of the standout features of the KM-1300SAH-E and KM-1300SRH-E is their impressive ice production capacity. They can produce up to 1,300 pounds of crescent-shaped ice per day, ensuring that businesses can keep up with high demand without compromising on quality. The crescent ice produced by these machines is ideal for a variety of applications, including beverages, food display, and ice for culinary purposes.

Both models are equipped with the latest Hoshizaki technology, which includes a powerful refrigeration system that enhances energy efficiency and cooling speed. This advanced technology not only helps in maintaining optimal ice-making temperatures but also reduces energy consumption, making these machines more eco-friendly and cost-effective over time.

Another significant aspect of the KM-1300 series is the user-friendly design. The machines feature a built-in storage bin that holds up to 1,002 pounds of ice, allowing for ample storage capacity to meet peak demands. The front access design ensures easy maintenance and cleaning, which is crucial for keeping the ice machine operating smoothly and hygienically.

The KM-1300SAH-E and KM-1300SRH-E are also designed with durability in mind. Constructed with stainless steel, they offer resistance against corrosion and wear, ensuring a long lifespan in demanding environments. Their robust design allows them to withstand the rigors of daily use in commercial settings.

In terms of safety features, Hoshizaki has integrated several technologies into these models. The cleaning and sanitizing cycles are automated, reducing the labor involved in maintaining sanitary conditions. Additionally, the ice machines are equipped with a self-diagnosis feature that alerts users to any potential issues, allowing for quick troubleshooting.

In conclusion, the Hoshizaki KM-1300SAH-E and KM-1300SRH-E ice machines exemplify the brand's commitment to quality, efficiency, and innovation. With their substantial ice production capabilities, advanced features, and ease of maintenance, these models are a smart investment for any commercial establishment that requires reliable ice-making solutions. Adopting these machines can significantly enhance operational efficiency while ensuring that customers receive the best service possible.