Hoshizaki KM-1300SAH-E, KM-1300SRH-E installation manual HOW to Remove Panels See Fig, Unpacking

Page 2

ENGLISH

IMPORTANT

1.In order to carry out safe and proper installa- tion of the product, please read this booklet carefully beforehand and follow the instruc- tions contained within.

2.On completion of the installation, start the icemaker to check for any abnormalities, and instruct the user on how to use and maintain the icemaker in accordance with the Instruc- tion Manual.

3.This booklet should be handed over to the user after the installation and be preserved by the user together with the Instruction Manual for any further consultation that may be necessary.

WARNING

The installation must be carried out by qualified personnel, in accordance with current regulations, according to the manufacturer’s instructions.

4)Remove the protective plastic film from the panels. If the icemaker is exposed to the sun or to heat, remove the film after the icemaker cools.

5)Check that the refrigerant lines do not rub or touch lines or other surfaces, and that the fan blade turns freely.

6)Check that the Compressor is snug on all mounting pads.

7)See the Nameplate on the Rear Panel, and check that your voltage supplied corresponds with the voltage specified on the Nameplate.

8)Remove the shipping tapes securing the Cube Guide.

2. HOW TO REMOVE PANELS - See Fig. 1

1. UNPACKING

WARNING

Children should not be allowed in reach of the packaging elements (plastic bags and expanded polystyrene) as they are potential sources of danger.

CAUTION

Remove shipping carton, tape(s) and packing. If packing material is left in the icemaker, it will not work properly.

Note: 1. This icemaker needs a storage bin. The recommended storage bin is HOSHIZAKI ICE STORAGE BIN, Model B-800 series.

2.The remote air-cooled model requires

HOSHIZAKI REMOTE CONDENSER UNIT, Model URC-12F-E.

1)After removing the packaging, make sure that the icemaker is in good condition. If in doubt, please do not use the equipment but apply to professionally qualified personnel. See the instruction sheet at- tached to the Storage Bin for its unpacking and installation guidelines.

2)Remove the panels to prevent damage when installing the icemaker. (See “2. HOW TO REMOVE PANELS.”)

3)Remove the package containing the accessories from the compressor compartment.

Fig. 1

a)Front Panel . . . . . Remove the two screws. Lift up and pull toward you.

b)Top Panel . . . . . . Remove the two screws, and then lift off.

c)Side Panel (R) . . .Remove the screw.

Pull slightly toward you, and take off.

d)Insulation Panel . . Remove the Thumbscrew. Lift up slightly, and pull toward you.

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents KM-1300SAH-E KM-1300SRH-E HOW to Remove Panels See Fig UnpackingInstallation LocationStacking TWO Icemakers SeeLocation Electrical ConnectionUnpacking This Appliance Must be EarthedInstallation Electrical Connection Water Supply and Drain Connections Stacking the Condenser UnitSee Fig Start UP KM-1300SAH-E KM-1300SRH-EOperation BIN Control CheckFinal Check List Have all electrical and piping connections been made?Achtung AuspackenAbnahme DER Platten Siehe Abbildung VorsichtAbb a StandortAbb Stapeln VON Zwei Eismaschinen Siehe Bild 4 Abb bAufstellung StromanschlussAuspacken Installation Stromanschluss Dieses Gerät Muss Geerdet WerdenWarnung Stapeln VON KondensatorenWASSER- UND ABWASSER- Anschlüsse Vgl. Abb KM-1300SAH-E KM-1300SRH-E Abb II. Einschalten Prüfung DER Behälterfüllstandsregelung BetriebCheckliste FÜR DIE Endüberprüfung Vea la figura DesembaladoCómo Retirar LOS Paneles Precaución UbicaciónInstalación Apilamiento DE DOS Dispensadores DE Hielo Ver figuras 4 yDesembalaje Conexión EléctricaAdvertencia Este Aparato SE Debe Conectar a Tierra UbicaciónInstalación Conexión Eléctrica Precaución Este Aparato Debe Estar Conectado a TierraConexiones DE Suministro DE Agua Y DESAGÜE- Vea la figura Apilamiento DE LA Unidad DE CondensaciónKM-1300SAH-E KM-1300SRH-E Arranque Inicial Operación Comprobación DEL Control DEL Recipiente DE AlmacenamientoLista Final DE Comprobación Avertissement DeballageLE Demontage DES Panneaux Voir Figure Emplacement Empilage DE Deux Distributeurs L’UN SUR L’AUTRE VoirAvertissement CET Appareil Doit Etre MIS a LA Terre EmplacementRaccordements Electriques DeballageInstallation Raccordements Electriques ’EAU ET DE LA Vidange Voir Figure Empilage DU CondenseurRaccordements DE L’ARRIVEE KM-1300SAH-E KM-1300SRH-E Mise EN Route Verification DE LA Commande DE Reservoir FonctionnementCheck List Finale Avvertenza DisimballaggioRimozione DEI Pannelli V. FIG AttenzioneInstallazione UbicazioneSovrapposizione Delle DUE Cubettatrici V. e Disimballaggio Collegamenti ElettriciAvvertenza Collegare IL Distributore a UNA Presa DI Terra PosizioneInstallazione Collegamenti Elettrici Sovrapposizione DEL Condensatore Collegamenti PER Alimentazione E Scarico AcquaAvviamento Funzionamento Controllo Della Funzionalità Della VaschettaControlli finali Belangrijk UitpakkenHET Verwijderen VAN DE Panelen Zie Afb WaarschuwingAfb a InstallatieLocatie Afb b HET Stapelen VAN Twee IjsdispensersZie Plaatsen Elektrische AansluitingenUitpakken Installatie Hoshizaki EuropeElektrische Aansluitingen HET Stapelen VAN DE Condensor Afb Aansluitingen Voor Watertoevoer EN -AFVOER Zie AfbAfb Opstarten Controle VAN DE BAK WerkingEindcontrole

KM-1300SRH-E, KM-1300SAH-E specifications

The Hoshizaki KM-1300SAH-E and KM-1300SRH-E are part of Hoshizaki's renowned line of ice makers, known for their reliability, efficiency, and high-quality ice production. These models are particularly well-suited for busy environments such as restaurants, cafes, and hotels where on-demand ice is essential for both food service and customer satisfaction.

One of the standout features of the KM-1300SAH-E and KM-1300SRH-E is their impressive ice production capacity. They can produce up to 1,300 pounds of crescent-shaped ice per day, ensuring that businesses can keep up with high demand without compromising on quality. The crescent ice produced by these machines is ideal for a variety of applications, including beverages, food display, and ice for culinary purposes.

Both models are equipped with the latest Hoshizaki technology, which includes a powerful refrigeration system that enhances energy efficiency and cooling speed. This advanced technology not only helps in maintaining optimal ice-making temperatures but also reduces energy consumption, making these machines more eco-friendly and cost-effective over time.

Another significant aspect of the KM-1300 series is the user-friendly design. The machines feature a built-in storage bin that holds up to 1,002 pounds of ice, allowing for ample storage capacity to meet peak demands. The front access design ensures easy maintenance and cleaning, which is crucial for keeping the ice machine operating smoothly and hygienically.

The KM-1300SAH-E and KM-1300SRH-E are also designed with durability in mind. Constructed with stainless steel, they offer resistance against corrosion and wear, ensuring a long lifespan in demanding environments. Their robust design allows them to withstand the rigors of daily use in commercial settings.

In terms of safety features, Hoshizaki has integrated several technologies into these models. The cleaning and sanitizing cycles are automated, reducing the labor involved in maintaining sanitary conditions. Additionally, the ice machines are equipped with a self-diagnosis feature that alerts users to any potential issues, allowing for quick troubleshooting.

In conclusion, the Hoshizaki KM-1300SAH-E and KM-1300SRH-E ice machines exemplify the brand's commitment to quality, efficiency, and innovation. With their substantial ice production capabilities, advanced features, and ease of maintenance, these models are a smart investment for any commercial establishment that requires reliable ice-making solutions. Adopting these machines can significantly enhance operational efficiency while ensuring that customers receive the best service possible.
Top Page Image Contents