Jackson AJ-44 technical manual Detergent Connection Point Machine rear view

Page 40

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS (CONTINUED)

The exhaust system must be sized to handle this volume for the dishmachine to operate as it was designed to.

ELECTRIC HEAT: The thermostats for the machines covered in this manual are factory set. They should not be adjusted except by an authorized service agent.

CHEMICAL FEEDER EQUIPMENT: The AJ-44CEL/CSL, AJ-66CEL/CSL, and AJ-80CEL/CSL are designed to operate with a third party chemical injection system. Jackson does not endorse any particular chemical injection system. The system select- ed must be able to provide detergent and sanitizer in the required concentrations. The minimum chlorine concentration for prop- er sanitization is 50 PPM. Furthermore, the selected feeder needs to be able to operate against a head of 25 PSI and deliver 7.38 ml of a 10% chlorine sanitizer per minute.

Detergent may be introduced into the unit through the removal of the bulkhead plug in the rear of the tub and replacing it with the third party detergent injection fitting. Remove the bulkhead plug in the side of the tub to install the detergent concentration probe.

For more information concerning detergent concerns, please refer to

Brass Plug the page entitled “Detergent Control”.

Detergent Connection Point

(Machine rear view)

The 1/8” brass plugs on the incoming plumbing rinse injector may be removed to install sanitizer and rinse aid injection fittings.

Brass Plugs

Back of Control Box

All wires for the chemical injectors should be routed through one of the extra openings in the back of the control box.

Terminals in the control box marked “CVS” provide a constant voltage signal whenever the drive motor is operating.

Terminals in the control box marked “DET” provide a voltage signal whenever the wash motor is operating.

Aid Connection Points

AJ-44C Series Technical Manual 7610-001-76-22

Issued: 03-21-2006 Revised: N/A

32

Image 40
Contents For Jackson Models AJ-66CELAJ-44CGP AJ-66CGP AJ-66CSLManufacturers Warranty ONE Year Limited Parts & Labor WarrantyStop Pare Arret Revision Made Applicable Details Date ECN AJ-44CSL Nomenclature for the Models Covered in this ManualTable of Contents Side Loader Section Parts Parts SectionD226 Steam Booster Section Electrical Schematics Viii Maintenance & Repair CentersSection Specification Information Specification Information AJ-44CE/CEL Models AJ-66CE/CEL ModelsAJ-44CGP Models AJ-66CGP ModelsAJ-80CS/CSL Models AJ-80CE/CEL ModelsD226 Steam Booster Specification Information AJ-44 Electric Left to Right Left to RightRight to Left AJ-44Information to Right AJ-44 GAS Right to InformationLeft AJ-44 Steam Left to RightSpecification Information AJ-44 Steam Right to Left Specification Information AJ-66 Electric Left to Right Left to RightSpecification Information AJ-66 Electric Right to Left Right to LeftSpecification Information AJ-66 GAS Left to Right Left to Right AJ-66 GAS Right toAJ-66 Steam Left to Specification Information AJ-66 Steam Right to Left Right to LeftLeft to Right Specification Information AJ-80 Electric Right to Left Specification Information AJ-80 GAS Left to Right Left to RightRight to Left AJ-80 GAS Right toAJ-80 Steam Left to Recommended Table FabricationSpecification Information AJ-80 Steam Right to Left Right to LeftSide Loader Left to Right Dimensions Section A-ASide Loader Right to Left Dimensions Side Loader Installed Dimensions D226 Steam Booster Dimensions D226 Steam Booster Plumbing Line Drawings Typical Electric and GAS Booster Dimensions Rear ViewSection Installation & Operation Instructions INSTALLATION/OPERATION Instructions Installation InstructionsIncoming Power Connection Detergent Connection Point Machine rear view Deliming Operations Preparation Changing the AJ-44CE/CS Direction of TravelINSTALLATION/OPERATION Instructions Removing the bracket nut INSTALLATION/OPERATION Instructions INSTALLATION/OPERATION Instructions Special Parts Please refer to the chart for placement of the curtains Side Loader Installation & Operation Instructions Equipment Mounting PlumbingShutdown for Service only OperationGAS Conveyor Hose Installation Conveyor Hose Installation GASDishmachine Operating Instructions Dishmachine Operation Instructions Changing Dual Sanitization Mode Drive Mechanism Maximum Speed AdjustmentOrange background Detergent Control Striker Plate Limit Switch Installation Instructions Installation InstructionsSection Preventative Maintenance Preventative Maintenance Preventative MaintenanceD226 Maintenance Maintenance of the Water Pressure RegulatorLubrication Chart for Drive Gear SHC-90WDrive Motor Gear Reducer Preventative Maintenance Lubrication & MaintenanceSection Troubleshooting Section Troubleshooting Common ProblemsTorque Settings Items Torque SpecD226 Common Problems Problem Power light does not illuminate
Related manuals
Manual 8 pages 11.95 Kb