Sherwood R-965 manual Connecting System Control, Room 2 connections

Page 12

Component to be triggered by DC when this unit's power is turned on

8. CONNECTING SYSTEM CONTROL

•Connect this jack to the DIGI LINK jack of the external Sherwood component that uses the DIGI LINK II or III remote control system.

Sherwood component with DIGI LINK II or III

CD player

Tape deck

DVD player

System control cord

ENGLISH

9. CONNECTING DC TRIGGER OUTs

•Connect components that need to be triggered by DC under certain conditions as follows :

• Connect a component to DC TRIGGER OUT 1 jack that allows DC 12 V to turn on or off when this unit’s power is turned on or off.

• Connect a component to DC TRIGGER OUT 2 jack that

Component to be triggered

allows DC 12 V to turn on or off when a specific input

by DC when a specific input

1

2

source is selected

DC TRIGGER OUT

source is selected or not.

12V d.c. 100mA

•For details, refer to the operating instructions of the components to be connected.

•To link DC TRIGGER OUT 2 with a specific input source, refer to “When selecting the DC TRIGGER 2 SETUP” on page 57.

Notes :

•This output voltage (12 V d.c., 100mA ) is for (status) control only, it is not sufficient for drive capability.

•When making DC TRIGGER connection, you should use the stereo mini cord, not a mono mini cord.

ROOM 2 connections

•ROOM 2 playback feature allows you to play a different program source in another room as well as one source in the main room at the same time.

•For ROOM 2 playback, connect the VIDEO 2 / ROOM 2 OUT jacks and the COAXIAL DIGITAL OUT to the amplifier, TV. etc. installed in another room, or connect the SURROUND BACK speaker terminals to the speakers.

•In case of using a pair of speakers only, you should assign the power amplifier for surround back channels to the ROOM 2. (For details, refer to “SETTING THE POWER AMP ASSIGN” on page 45.)

Note :

•To minimize hum or noise, use high quality connection cords.

Main room

•When connecting VIDEO 2/ROOM 2 OUTs to the components.

This receiver

•When connecting SURROUND BACK speaker terminals to the speakers.

This receiver

Another room(Room 2)

ININ

S-VIDEO VIDEO (COMPOSITE)

TV or projector

LAUDIO

R IN

COAXIAL

DIGITAL IN

AmplifierSpeakers

Speakers

left right

12

Image 12

Contents 965 Introduction Read this Before Operating Your UnitSafety Instruction Contents Connecting Antennas System ConnectionsConnecting Audio Components Component video input default settings Digital input default settings USB audio connectionConnecting 8CH Direct INs Surround speakers a and B Surround back speakersSpeaker placement Front left and right speakers and center speakerConnecting System Control Room 2 connectionsConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Front Panel Controls Dolby PL II Music ParameterFluorescent Display Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons TapePlay PLAY/PAUSE Loading Batteries AUD1Entering a Setup Code Enter the 3 digit setup code aiming Room 2 Remote Controls Remote Control Operation RangeOperations Listening to a Program SourceBefore operation When CD, AUX or Video 1~ Video 6 is selected Adjusting the tone bass and trebleMuting the sound Listening with the headphones Achieving higher purity of sound qualityCompensating for edgy or shrill movie sound tracks Surround Sound Surround modesTheater Front L/R Center Select the desired surround mode Enjoying Surround Sound2CH downmix mode To listen in a Dolby Pro Logic IIx modeTo listen in a Dolby Virtual Speaker mode Selecting the surround back channel mode as connected To listen in a Dolby Headphone modeAdjusting each channel level with test tone Adjusting the current channel levelsAdjust the level of the selected channel as Desired Auto tuning Manual tuningAuto presetting Manual presetting Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness Other FunctionsCompressing the dynamic range Dolby Digital sources onlyEntering a label Correcting or clearing a labelRoom 2 Source Playback Press the Room 2 buttonUsing the OSD OSD Menu SettingsCurrent Status Display When selecting the Power AMP Assign Setting the Power AMP Assign Setting the Speaker SetupWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance When selecting the Virtual Speaker Setup Virtual Speaker mode changes as followsWhen selecting the Subwoofer When selecting the Subwoofer Mode When selecting the Crossover FrequencyWhen selecting the Auto Speaker Setup PreparationsDB , S , 1 0 f t Setting the System Setup When selecting the Digital Input SetupWhen selecting the Tone Control When Cinema EQ mode is selectedWhen Tone Defeat mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup VideoWhen selecting the Video 2 OUT When selecting the DC Trigger 2 SetupWhen the DC Trigger 2 mode is set to On When selecting the Digital RE-MASTERINGWhen selecting the A/V Sync Setting the Surround Setup When Decoding Mode is selectedWhen the Surround Mode is selected When thez Dolby surround mode is selectedWhen the Dynamic Range is selected When selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dimension control Setting the CH Level Setup When selecting the Preset 1 orWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Room 2 Feed mode When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section965