Sherwood R-965 manual Loading Batteries, AUD1

Page 20

OPERATING COMPONENTS WITH REMOTE CONTROL

Enter the setup code of the components

1 respectively, referring to “ENTERING A SETUP CODE” (page 21).

Turn on the components you want to

2 operate.

Select the device on the main menu of the

3 remote control corresponding to the component you want to operate.

Example) When selecting “AUD 1” or “AUD 2” to operate this receiver.

STANDBYPOWER ON

MAIN

 

 

AUD1

AUD2

 

CD

TV

 

DVD

VCR

 

TAPE

SAT

 

AUX

CABLE

 

AUD1

The device selected presentl

Then the page menu of the selected device will be displayed.

Press the button corresponding to the

4 operation you want while aiming the remote control at the REMOTE SENSOR on the component.

When operating a Sherwood CD player or tape deck using the system remote control, aim the remote control at the REMOTE SENSOR on this unit.

However, in case of Sherwood DVD player or TV, aim it at the REMOTE SENSOR on the corresponding component.

In case of selecting a function on the page menu of the selected device.

Find a function with pressing the PAGE button repeatedly and then press the button corresponding to the desired function.

Example) when selecting a function on the AUD 1’s page menu.

Functions on the page 1Functions on the page 2

AUD1

 

 

AUD1

 

 

 

 

 

 

TUNER

VID1

VID6

7.1IN

CD

VID2

DTS

PL2MV

T.MON

VID3

DOLBY

PL2MS

AUX

VID4

PCM

NOE6C

PHONO

VID5

MPEG

NEO6M

 

 

 

PAGE1

PAGE2

REMOTE CONTROL OPERATION RANGE

Use the remote control within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor.

PAGE

MAIN

FAV

VOL

 

 

1 2 3

4 5 6

7 8 9

0

MI M2 M3

LOADING BATTERIES

When the remote control does not operate or “LOW BATTERY” is displayed on the LCD screen, etc., the old batteries should be replaced.

Remove the cover.

1

2

Load four alkaline batteries (“AAA” size,

1.5V) matching the polarity.

ENGLISH

20

Image 20
Contents 965 Introduction Read this Before Operating Your UnitSafety Instruction Contents Connecting Antennas System ConnectionsConnecting Audio Components Component video input default settings Digital input default settings USB audio connectionConnecting 8CH Direct INs Surround speakers a and B Surround back speakersSpeaker placement Front left and right speakers and center speakerConnecting System Control Room 2 connectionsConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Front Panel Controls Dolby PL II Music ParameterFluorescent Display Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons TapePlay PLAY/PAUSE Loading Batteries AUD1Entering a Setup Code Enter the 3 digit setup code aiming Room 2 Remote Controls Remote Control Operation RangeBefore operation OperationsListening to a Program Source When CD, AUX or Video 1~ Video 6 is selected Adjusting the tone bass and trebleCompensating for edgy or shrill movie sound tracks Muting the sound Listening with the headphonesAchieving higher purity of sound quality Surround Sound Surround modesTheater Front L/R Center Select the desired surround mode Enjoying Surround SoundTo listen in a Dolby Virtual Speaker mode 2CH downmix modeTo listen in a Dolby Pro Logic IIx mode Selecting the surround back channel mode as connected To listen in a Dolby Headphone modeAdjusting each channel level with test tone Adjusting the current channel levelsAdjust the level of the selected channel as Desired Auto presetting Auto tuningManual tuning Manual presetting Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness Other FunctionsCompressing the dynamic range Dolby Digital sources onlyEntering a label Correcting or clearing a labelRoom 2 Source Playback Press the Room 2 buttonCurrent Status Display Using the OSDOSD Menu Settings When selecting the Power AMP Assign When selecting the Speaker Configuration Setting the Power AMP AssignSetting the Speaker Setup Each time these buttons are pressed, and are When selecting the Speaker Distance When selecting the Virtual Speaker Setup Virtual Speaker mode changes as followsWhen selecting the Subwoofer When selecting the Subwoofer Mode When selecting the Crossover FrequencyWhen selecting the Auto Speaker Setup PreparationsDB , S , 1 0 f t Setting the System Setup When selecting the Digital Input SetupWhen Tone Defeat mode is selected When selecting the Tone ControlWhen Cinema EQ mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup VideoWhen selecting the Video 2 OUT When selecting the DC Trigger 2 SetupWhen the DC Trigger 2 mode is set to On When selecting the Digital RE-MASTERINGWhen selecting the A/V Sync Setting the Surround Setup When Decoding Mode is selectedWhen the Dynamic Range is selected When the Surround Mode is selectedWhen thez Dolby surround mode is selected When selecting the Dimension control When selecting the Panorama modeWhen selecting the Center Width control When selecting the Preset 1 Trim or Preset 2 Trim Setting the CH Level SetupWhen selecting the Preset 1 or When selecting the Channel Level Trim When selecting the LFE Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Room 2 Feed mode When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section965