Sherwood R-965 manual Connecting PC for Upgrades

Page 14

12. CONNECTING PC FOR UPGRADES

•This receiver incorporates USB as well as RS-232C terminal that may be used in the future to update the operating software so that it will be able to support new digital audio formats, external control by using an external device and the like.

•Connect either USB or RS-232C terminal to your PC(You don’t need to do both).

PC with USB

or RS-232C port

UPGRADE switch

ENGLISH

Notes :

•Be sure to set the UPGRADE switch to “SVC”(service) before updating.

•This switch should be set to “OPR”(operation) during normal operation except for upgrades.

If not, this unit will not operate normally.

•Programming for upgrades and external control requires specialized programming knowledge and for that reason we recommend that it only be done by qualified installers. For more information on future upgrades and external control, visit the Sherwood web site at www.sherwoodamerica.com or contact your dealer.

•Do not disconnect the connection cable while updating the operating software, etc. Should this happen, it may be result in malfunction or cause damage to the unit.

13. SWITCHED AC OUTLETS

•Theses outlets are switched on(power-on mode) and

off(standby mode) according to power control as follows(Maximum total capacity is 100 W, 1 A).

Standby mode - Switched AC outlet off

Power-on mode - Switched AC outlet on

14. AC INLET

•Plug the supplied AC input cord into this AC INLET and then into the wall AC outlet.

Note:

•Do not use an AC input cord other than the one supplied with this unit. The AC input cord supplied is designed for use with this unit and should not be used with any other device.

To a wall AC outlet.

14

Image 14

Contents 965 Introduction Read this Before Operating Your UnitSafety Instruction Contents Connecting Antennas System ConnectionsConnecting Audio Components Component video input default settings Digital input default settings USB audio connectionConnecting 8CH Direct INs Surround speakers a and B Surround back speakersSpeaker placement Front left and right speakers and center speakerConnecting System Control Room 2 connectionsConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Front Panel Controls Dolby PL II Music ParameterFluorescent Display Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons TapePlay PLAY/PAUSE Loading Batteries AUD1Entering a Setup Code Enter the 3 digit setup code aiming Room 2 Remote Controls Remote Control Operation RangeBefore operation OperationsListening to a Program Source When CD, AUX or Video 1~ Video 6 is selected Adjusting the tone bass and trebleCompensating for edgy or shrill movie sound tracks Muting the sound Listening with the headphonesAchieving higher purity of sound quality Surround Sound Surround modesTheater Front L/R Center Select the desired surround mode Enjoying Surround SoundTo listen in a Dolby Virtual Speaker mode 2CH downmix modeTo listen in a Dolby Pro Logic IIx mode Selecting the surround back channel mode as connected To listen in a Dolby Headphone modeAdjusting each channel level with test tone Adjusting the current channel levelsAdjust the level of the selected channel as Desired Auto presetting Auto tuningManual tuning Manual presetting Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Compressing the dynamic range Operating the sleep timer Adjusting the brightnessOther Functions Dolby Digital sources onlyEntering a label Correcting or clearing a labelRoom 2 Source Playback Press the Room 2 buttonCurrent Status Display Using the OSDOSD Menu Settings When selecting the Power AMP Assign When selecting the Speaker Configuration Setting the Power AMP AssignSetting the Speaker Setup Each time these buttons are pressed, and are When selecting the Speaker Distance When selecting the Virtual Speaker Setup Virtual Speaker mode changes as followsWhen selecting the Subwoofer When selecting the Subwoofer Mode When selecting the Crossover FrequencyWhen selecting the Auto Speaker Setup PreparationsDB , S , 1 0 f t Setting the System Setup When selecting the Digital Input SetupWhen Tone Defeat mode is selected When selecting the Tone ControlWhen Cinema EQ mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup VideoWhen selecting the Video 2 OUT When selecting the DC Trigger 2 SetupWhen the DC Trigger 2 mode is set to On When selecting the Digital RE-MASTERINGWhen selecting the A/V Sync Setting the Surround Setup When Decoding Mode is selectedWhen the Dynamic Range is selected When the Surround Mode is selectedWhen thez Dolby surround mode is selected When selecting the Dimension control When selecting the Panorama modeWhen selecting the Center Width control When selecting the Preset 1 Trim or Preset 2 Trim Setting the CH Level SetupWhen selecting the Preset 1 or When selecting the Channel Level Trim When selecting the LFE Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Room 2 Feed mode When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section965