Sherwood R-965 manual Adjust the level of the selected channel as Desired

Page 34

Adjust the level of the selected channel as

2 desired.

		PAGE	MAIN
		VOL		CH/
		or		ADJUST
		1	2	3
DOWN	UP	4	5	6
DOWN	UP	7	8	9
			0
		MI	M2	M3

3	Repeat the above steps	and	to adjust
3	each channel level.

ENGLISH

Adjusting the Dolby Pro Logic IIx / Dolby Pro Logic II Music parameters

•When selecting either the Dolby Pro Logic IIx Music mode or the Dolby Pro Logic II Music mode depending on whether “S/B CH” is set to “None” or not, you can adjust the various surround parameters for optimum surround effect.(Refer to “When selecting the SPEAKER CONFIGURATION” on page 45.)

•In case of PL IIx MUSIC mode, only when original surround mode is “BYPASS” mode or 2 channel digital signals from Dolby Digital sources, etc. are input, these parameter settings affect the surround effects.

Press the DOLBY PL II MUSIC PARAMETER button to select the desired parameter.

1

• Each time this button is pressed, the parameter changes and is displayed for several seconds as follows;

or

STANDBY

POWER ON

AUD2

SLEEP D/A

DIMM S.A/B

ROOM2 SUR.B

T.TON PURE

OSD PARA.

PAGE1

Panorama mode(“PANORAMA”, default value : OFF) This mode extends the front stereo image to include the surround speakers for an exciting “wraparound” effect with side wall imaging. Select “OFF” or “ON”.

Center width control(“C-WIDTH”, default value : 0)

This adjusts the center image so it may be heard only from the center speaker, only from the left/right speakers as a phantom image, or from all three front speakers to varying degrees.

The control can be set in 8 steps from 0 to 7.

Dimension control(“DIMENSION”, default value : 0)

This gradually adjusts the soundfield either towards the front or towards the rear. The control can be set in 7 steps from -3 to +3.

At the desired parameter, adjust it as desired.

2

PAGE	MAIN
VOL	CH/
or	ADJUST

1 2 3

4 5 6

7 8 9

0

MI M2 M3

• If the parameter display disappears, start from the step again.

3	Repeat the above steps	and	to
3	adjust other parameters.

34

Image 34

Contents 965 Introduction Read this Before Operating Your UnitSafety Instruction Contents Connecting Antennas System ConnectionsConnecting Audio Components Component video input default settings Digital input default settings USB audio connectionConnecting 8CH Direct INs Surround speakers a and B Surround back speakersSpeaker placement Front left and right speakers and center speakerConnecting System Control Room 2 connectionsConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Front Panel Controls Dolby PL II Music ParameterFluorescent Display Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons TapePlay PLAY/PAUSE Loading Batteries AUD1Entering a Setup Code Enter the 3 digit setup code aiming Room 2 Remote Controls Remote Control Operation RangeListening to a Program Source OperationsBefore operation When CD, AUX or Video 1~ Video 6 is selected Adjusting the tone bass and trebleAchieving higher purity of sound quality Muting the sound Listening with the headphonesCompensating for edgy or shrill movie sound tracks Surround Sound Surround modesTheater Front L/R Center Select the desired surround mode Enjoying Surround SoundTo listen in a Dolby Pro Logic IIx mode 2CH downmix modeTo listen in a Dolby Virtual Speaker mode Selecting the surround back channel mode as connected To listen in a Dolby Headphone modeAdjusting each channel level with test tone Adjusting the current channel levelsAdjust the level of the selected channel as Desired Manual tuning Auto tuningAuto presetting Manual presetting Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Compressing the dynamic range Operating the sleep timer Adjusting the brightnessOther Functions Dolby Digital sources onlyEntering a label Correcting or clearing a labelRoom 2 Source Playback Press the Room 2 buttonOSD Menu Settings Using the OSDCurrent Status Display When selecting the Power AMP Assign Setting the Speaker Setup Setting the Power AMP AssignWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance When selecting the Virtual Speaker Setup Virtual Speaker mode changes as followsWhen selecting the Subwoofer When selecting the Subwoofer Mode When selecting the Crossover FrequencyWhen selecting the Auto Speaker Setup PreparationsDB , S , 1 0 f t Setting the System Setup When selecting the Digital Input SetupWhen Cinema EQ mode is selected When selecting the Tone ControlWhen Tone Defeat mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup VideoWhen selecting the Video 2 OUT When selecting the DC Trigger 2 SetupWhen the DC Trigger 2 mode is set to On When selecting the Digital RE-MASTERINGWhen selecting the A/V Sync Setting the Surround Setup When Decoding Mode is selectedWhen thez Dolby surround mode is selected When the Surround Mode is selectedWhen the Dynamic Range is selected When selecting the Center Width control When selecting the Panorama modeWhen selecting the Dimension control When selecting the Preset 1 or Setting the CH Level SetupWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Room 2 Feed mode When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section965