Sherwood R-965 manual Operations, Listening to a Program Source, Before operation

Page 24

Operations

Notes : • Before operating this receiver with the supplied remote control, refer to “ Universal Remote Controls” on page 17 for details about operation.

•Before operating this receiver, first set this unit as desired for optimum performance, doing the OSD menu setting procedures. (For details, refer to “OSD Menu Settings” on page 43.)

LISTENING TO A PROGRAM SOURCE

ENGLISH

Before operation

• Enter the standby mode.

• The STANDBY button lights up in amber. This means that the receiver is not disconnected from the AC mains and a small amount of current is retained to support the operation readiness.

•To switch the power off, push the POWER switch again.

•Then power is cut off and the STANDBY button goes off.

In the standby mode, turn the power on.

1

STANDBY

POWER ON

STANDBY

or

1 2 3

4 5 6

7 8 9

0

•Each time the STANDBY button on the front panel is pressed, the receiver is turned on to enter the operating mode (the STANDBY button lights up in blue) or off to enter the standby mode(the STANDBY button lights up in amber).

•On the remote control, press the POWER ON button to enter the operating mode or press the STANDBY button to enter the standby mode.

•In the standby mode, if the INPUT SELECTOR button is pressed, the receiver is turned on automatically and the desired input is selected.

Switch the speakers on.

2

•Then the SPEAKER indicator ( ) lights up and the sound can be heard from the speakers.

•When using the headphones for private listening, press this button again to switch the speakers off,

then the SPEAKER indicator ( ) goes off(speaker off mode).

Select the desired input source.

3

STANDBY

POWER ON

AUD1

 

 

TUNER

VID1

 

CD

VID2

 

T.MON

VID3

 

AUX

VID4

or

PHONO

VID5

PAGE1

•Each time the “AUDIO” button is pressed, the input source changes as follows:

PHONO TUNER CD AUX

(frequency display)

•Each time the “VIDEO” button is pressed, the input source changes as follows:

VIDEO 1 VIDEO 2 ------- VIDEO 6

•When the TAPE MONITOR button is set to on so that “TAPE MON” lights up, other inputs can not be heard from the speakers.

To listen to an input source except TAPE MONITOR, be sure to set the TAPE MONITOR button to off.

TAPE MONITOR function

You can connect either a tape deck or a graphic equalizer to the receiver’s TAPE MONITOR jacks.

Only when you listen to the component connected to these jacks, set the TAPE MONITOR button to on.

If you connect a 3-head tape deck, you can listen to the sound being recorded during recording, not the source sound.

For further details, refer to the operating instructions of the component connected.

When selecting the 8 CH DIRECT as desired

 

STANDBY

POWER ON

 

AUD1

 

 

VID6

7.1IN

 

DTS

PL2MV

or

DOLBY

PL2MS

PCM

NEO6C

MPEG NEO6M

PAGE2

•Depending on the power amplifier setting for the surround back channels and the surround back speaker setting, “8(, 7 or 6) CH DIRECT” is displayed and the 8(/7/6) separate analog signals from the component connected to this input pass through the tone, volume and bass management(if selected) circuits only and can be heard from your speakers.(In case that the TAPE MONITOR button is set to on, the TAPE MONITOR button is automatically set to off.)

•Press the 8 CH DIRECT button or select the desired input source to cancel the 8 CH direct function.

•These analog signals can be heard only. They cannot be recorded.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents 965 Introduction Read this Before Operating Your UnitSafety Instruction Contents Connecting Antennas System ConnectionsConnecting Audio Components Component video input default settings Digital input default settings USB audio connectionConnecting 8CH Direct INs Surround speakers a and B Surround back speakersSpeaker placement Front left and right speakers and center speakerConnecting System Control Room 2 connectionsConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Front Panel Controls Dolby PL II Music ParameterFluorescent Display Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons TapePlay PLAY/PAUSE Loading Batteries AUD1Entering a Setup Code Enter the 3 digit setup code aiming Room 2 Remote Controls Remote Control Operation RangeOperations Listening to a Program SourceBefore operation When CD, AUX or Video 1~ Video 6 is selected Adjusting the tone bass and trebleMuting the sound Listening with the headphones Achieving higher purity of sound qualityCompensating for edgy or shrill movie sound tracks Surround Sound Surround modesTheater Front L/R Center Select the desired surround mode Enjoying Surround Sound2CH downmix mode To listen in a Dolby Pro Logic IIx modeTo listen in a Dolby Virtual Speaker mode Selecting the surround back channel mode as connected To listen in a Dolby Headphone modeAdjusting each channel level with test tone Adjusting the current channel levelsAdjust the level of the selected channel as Desired Auto tuning Manual tuningAuto presetting Manual presetting Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness Other FunctionsCompressing the dynamic range Dolby Digital sources onlyEntering a label Correcting or clearing a labelRoom 2 Source Playback Press the Room 2 buttonUsing the OSD OSD Menu SettingsCurrent Status Display When selecting the Power AMP Assign Setting the Power AMP Assign Setting the Speaker SetupWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance When selecting the Virtual Speaker Setup Virtual Speaker mode changes as followsWhen selecting the Subwoofer When selecting the Subwoofer Mode When selecting the Crossover FrequencyWhen selecting the Auto Speaker Setup PreparationsDB , S , 1 0 f t Setting the System Setup When selecting the Digital Input SetupWhen selecting the Tone Control When Cinema EQ mode is selectedWhen Tone Defeat mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup VideoWhen selecting the Video 2 OUT When selecting the DC Trigger 2 SetupWhen the DC Trigger 2 mode is set to On When selecting the Digital RE-MASTERINGWhen selecting the A/V Sync Setting the Surround Setup When Decoding Mode is selectedWhen the Surround Mode is selected When thez Dolby surround mode is selectedWhen the Dynamic Range is selected When selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dimension control Setting the CH Level Setup When selecting the Preset 1 orWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Room 2 Feed mode When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section965
Top Page Image Contents