Sherwood R-965 manual Setting the CH Level Setup, When selecting the Preset 1 or

Page 63

SETTING THE CH LEVEL SETUP

ENGLISH

C H L E V E L S E T U P

P R E S E T 1 : C AL L

P R E S E T 1

T R I M

P R E S E T 2

: C AL L

P R E S E T 2

T R I M

C H L E V E L T R I M

L F E L E V E L T R I M

, : S e l e c t

R E T U R N : B a c k

E N T E R : C a l l

To recall the channel levels memorized into preset memory or to memorize the channel levels adjusted in the CH LEVEL TRIM menu, etc.

To memorize the adjusted channel levels into preset memory.

To adjust the current channel levels as desired.

To adjust LFE (Low Frequency Effect) levels included in Dolby Digital, DTS and MPEG program sources.

When selecting the PRESET 1 or

PRESET 2

•You can recall the memorized channel levels whenever you want or can memorize the channel levels adjusted in the CH LEVEL TRIM men, etc. into preset memory.

Press the CURSOR UP()/DOWN( )

1 buttons to select the PRESET 1 or PRESET 2 .

PAGE	MAIN	FAV
VOL

1 2 3

4 5 6

7 8 9

0

MI M2 M3

2	Press the CURSOR
	LEFT( )/RIGHT( ) buttons to select
	the desired mode, then press the ENTER

button.

PAGE	MAIN	FAV
VOL

1 2 3

4 5 6

7 8 9

0

MI M2 M3

RNC-510

•Each time these buttons are pressed , the mode changes as follows :

CALL : Select this to recall the channel levels memorized into preset memory .

SAVE : Select this to memorize the channel levels adjusted in the CH LEVEL TRIM menu or in “Adjusting the current channel levels” procedure on page 33.

When selecting the PRESET 1 TRIM or PRESET 2 TRIM

•You can adjust the channel levels directly in the PRESET TRIM menu and can memorize them into preset memory.

Press the CURSOR UP()/DOWN( ) buttons to select the PRESET 1TRIM or PRESET 2 TRIM,

1 then press the ENTER button.

Example) When the PRESET 2 TRIM is selected .

PAGE	MAIN	FAV
VOL

1 2 3

4 5 6

7 8 9

0

	P R E S E T 2	T R I M
F L	: - - - - - -	- - - - - - : 0 dB
F C : - - - - - -		- - - - - - : 0 dB
F R : - - - - - -		- - - - - - : 0 dB
S R : - - - - - -		- - - - - - : 0 dB
B R	: - - - - - -	- - - - - - : 0 dB
B L : - - - - - -		- - - - - - : 0	dB
S L : - - - - - -		- - - - - - : 0	dB
SW : - - - - - -		- - - - - - : 0	dB
R E T U R N : B a c k		, : S e l e c t

MI M2 M3

RNC-510

63

Image 63

Contents 965 Read this Before Operating Your Unit IntroductionSafety Instruction Contents System Connections Connecting AntennasConnecting Audio Components Component video input default settings USB audio connection Digital input default settingsConnecting 8CH Direct INs Surround back speakers Surround speakers a and BFront left and right speakers and center speaker Speaker placementRoom 2 connections Connecting System ControlConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Dolby PL II Music Parameter Front Panel ControlsFluorescent Display Digi Link system remote controls Universal Remote ControlsTape Function Table of the Numbered ButtonsPlay PLAY/PAUSE AUD1 Loading BatteriesEntering a Setup Code Enter the 3 digit setup code aiming Remote Control Operation Range Room 2 Remote ControlsOperations Listening to a Program SourceBefore operation Adjusting the tone bass and treble When CD, AUX or Video 1~ Video 6 is selectedMuting the sound Listening with the headphones Achieving higher purity of sound qualityCompensating for edgy or shrill movie sound tracks Surround modes Surround SoundTheater Front L/R Center Enjoying Surround Sound Select the desired surround mode2CH downmix mode To listen in a Dolby Pro Logic IIx modeTo listen in a Dolby Virtual Speaker mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connectedAdjusting the current channel levels Adjusting each channel level with test toneAdjust the level of the selected channel as Desired Auto tuning Manual tuningAuto presetting Tuning to preset stations Manual presettingListening to FM stereo broadcasts Scanning preset stations in sequenceDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorDigital Audio Recording with MD Recorder Dolby Digital sources only Operating the sleep timer Adjusting the brightnessOther Functions Compressing the dynamic rangeCorrecting or clearing a label Entering a labelPress the Room 2 button Room 2 Source PlaybackUsing the OSD OSD Menu SettingsCurrent Status Display When selecting the Power AMP Assign Setting the Power AMP Assign Setting the Speaker SetupWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance Virtual Speaker mode changes as follows When selecting the Virtual Speaker SetupWhen selecting the Subwoofer When selecting the Crossover Frequency When selecting the Subwoofer ModePreparations When selecting the Auto Speaker SetupDB , S , 1 0 f t When selecting the Digital Input Setup Setting the System SetupWhen selecting the Tone Control When Cinema EQ mode is selectedWhen Tone Defeat mode is selected When selecting the Current Video When selecting the OSD Auto DisplayVideo When selecting the Component Video SetupWhen selecting the DC Trigger 2 Setup When selecting the Video 2 OUTWhen selecting the Digital RE-MASTERING When the DC Trigger 2 mode is set to OnWhen selecting the A/V Sync When Decoding Mode is selected Setting the Surround SetupWhen the Surround Mode is selected When thez Dolby surround mode is selectedWhen the Dynamic Range is selected When selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dimension control Setting the CH Level Setup When selecting the Preset 1 orWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Room 2 Feed modeProblem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications965