Sherwood R-965 manual Room 2 Source Playback, Press the Room 2 button

Page 42

ROOM 2 SOURCE PLAYBACK

•This function allows enjoying one source in the main room and playing another in a different room at the same time.

•The analog signals from the 8 CH DIRECT inputs and TAPE MONITOR INs cannot be output from the (VIDEO 2/) ROOM 2 OUTs and the digital signals from the USB terminal cannot be output from the COAXIAL DIGITAL OUT, meaning no playback in a different room.

•When you connect the multi-room system kit to the IR IN jack of this receiver, you can control this receiver with not only the universal remote control unit but also the ROOM 2 remote control unit in a different room, too.

(For details, refer to “CONNECTING MULTI-ROOM SYSTEM KIT” on page 13 and “ROOM 2 Remote Controls” on page 23.)

CAUTION : Even when the ROOM 2 function is deactivated, if the VIDEO 2 OUT is set to On, the signals of the selected source as a main room source will be output from the VIDEO 2/ROOM 2 OUTs.(For details, refer to “When selecting the VIDEO 2 OUT” on page 57.)

When using the ROOM 2 remote control unit

 

 

When using the universal remote control unit or the

• You can use the ROOM 2 function with the ROOM 2

 

buttons on the front panel.

 

 

remote control unit more conveniently.

 

 

 

1

Press the ROOM 2 button.

 

1

Press the ROOM 2 button.

ROOM2

 

 

 

 

 

 

 

 

 

STANDBY

 

POWER ON

 

 

 

 

 

 

AUD2

 

 

 

 

 

 

 

SLEEP

D/A

 

 

 

 

 

 

 

DIMM

S.A/B

 

 

 

 

 

 

or

ROOM2

SUR.B

• “R2” lights up and “(R2)~” is displayed for several

 

 

 

T.TON

PURE

 

 

 

 

PAGE1

 

 

 

 

 

 

 

OSD

PARA.

seconds and the ROOM 2 function is activated.

 

 

 

 

 

 

• To cancel the ROOM 2 function, press it again.

 

 

 

 

 

 

Then “R2” goes off.

 

 

 

• “R2” lights up and “(R2)~” is displayed for several seconds

• In the operating mode, when one of the ROOM 2 INPUT

 

 

and the ROOM 2 function is activated.

 

SELECTOR buttons on this remote control is pressed, the

• To cancel the ROOM 2 function, press it again.

ROOM 2 function is automatically activated without

 

 

 

 

Then “R2” goes off.

 

 

pressing the ROOM 2 button and the desired input is

 

 

• You can cancel the ROOM 2 function with using these

selected.

 

 

 

 

 

 

 

 

buttons even in the standby mode.

 

 

 

 

 

 

 

 

 

2

Select the desired

PHONO

CD

TUNER

2

Select the desired input as a ROOM 2 source

input as a ROOM 2

AUX

 

 

while displaying “(R2)~”.

 

source.

 

 

AUDIO

 

 

 

 

VIDEO 1

VIDEO 2

VIDEO 3

 

 

 

 

 

VIDEO 4

VIDEO 5

VIDEO 6

 

 

 

 

VIDEO

•The selected ROOM 2 source is displayed for several seconds as follows: (R2) PHONO, (R2) TUNER, (R2) CD, (R2) AUX, (R2) VIDEO 1~6.

•Only these sources can be played in another room.

•When an audio program source is selected, as a ROOM 2

source, the image of the video program source selected

 

 

previously can be played separately, too. (For details, refer to

• The selected ROOM 2 source is displayed for several

“ SETTING THE ROOM2 FEED SETUP” on page 66.)

seconds.

 

• The MUTE and VOLUME UP/DOWN( / ) buttons on this

• Only while displaying “(R2)~”, the volume level for the

remote control can be available only when the ROOM 2

ROOM 2 source can be adjusted.

function is operating.

• When “(R2)~” is not displayed, press the ROOM 2 button

Note:

 

briefly twice.

• When the muting effect for the ROOM 2 source is operating,

 

 

“MUTE” is flickering.

 

 

 

 

 

 

3

Start play on the component related to the

3

Start play on the component related to the

ROOM 2 source.

ROOM 2 source.

Notes:

•When the pure audio function is activated for the main room source, the video signals of the ROOM 2 source cannot be output, too.

•Even when this receiver enters the standby mode, in such a case that “R2” lights up still and the STANDBY button lights up in blue as it does in the operating mode, meaning only the ROOM 2 circuitry operates, the ROOM 2 source can be played independently.

•When the ROOM 2 function is operating in the standby mode, only the ROOM 2 remote control unit is available.

•When you do not use the ROOM 2 function, cancel the ROOM 2 function to save electricity.

•For ROOM 2 volume adjustment, refer to “SETTING THE ROOM 2 FEED SETUP” on page 66.

ENGLISH

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents 965 Introduction Read this Before Operating Your UnitSafety Instruction Contents Connecting Antennas System ConnectionsConnecting Audio Components Component video input default settings Digital input default settings USB audio connectionConnecting 8CH Direct INs Surround speakers a and B Surround back speakersSpeaker placement Front left and right speakers and center speakerConnecting System Control Room 2 connectionsConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Front Panel Controls Dolby PL II Music ParameterFluorescent Display Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons TapePlay PLAY/PAUSE Loading Batteries AUD1Entering a Setup Code Enter the 3 digit setup code aiming Room 2 Remote Controls Remote Control Operation RangeOperations Listening to a Program SourceBefore operation When CD, AUX or Video 1~ Video 6 is selected Adjusting the tone bass and trebleMuting the sound Listening with the headphones Achieving higher purity of sound qualityCompensating for edgy or shrill movie sound tracks Surround Sound Surround modesTheater Front L/R Center Select the desired surround mode Enjoying Surround Sound2CH downmix mode To listen in a Dolby Pro Logic IIx modeTo listen in a Dolby Virtual Speaker mode Selecting the surround back channel mode as connected To listen in a Dolby Headphone modeAdjusting each channel level with test tone Adjusting the current channel levelsAdjust the level of the selected channel as Desired Auto tuning Manual tuningAuto presetting Manual presetting Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Compressing the dynamic range Operating the sleep timer Adjusting the brightnessOther Functions Dolby Digital sources onlyEntering a label Correcting or clearing a labelRoom 2 Source Playback Press the Room 2 buttonUsing the OSD OSD Menu SettingsCurrent Status Display When selecting the Power AMP Assign Setting the Power AMP Assign Setting the Speaker SetupWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance When selecting the Virtual Speaker Setup Virtual Speaker mode changes as followsWhen selecting the Subwoofer When selecting the Subwoofer Mode When selecting the Crossover FrequencyWhen selecting the Auto Speaker Setup PreparationsDB , S , 1 0 f t Setting the System Setup When selecting the Digital Input SetupWhen selecting the Tone Control When Cinema EQ mode is selectedWhen Tone Defeat mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup VideoWhen selecting the Video 2 OUT When selecting the DC Trigger 2 SetupWhen the DC Trigger 2 mode is set to On When selecting the Digital RE-MASTERINGWhen selecting the A/V Sync Setting the Surround Setup When Decoding Mode is selectedWhen the Surround Mode is selected When thez Dolby surround mode is selectedWhen the Dynamic Range is selected When selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dimension control Setting the CH Level Setup When selecting the Preset 1 orWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Room 2 Feed mode When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section965
Top Page Image Contents