Sherwood R-965 manual Other Functions, Compressing the dynamic range, Dolby Digital sources only

Page 40

OTHER FUNCTIONS

Compressing the dynamic range

 

Adjust the dynamic range as desired.

 

2

(Dolby Digital sources only)

This function compresses the dynamic range of previously specified parts of the Dolby Digital sound track(with extremely high volume)to minimize the difference in volume between the specified and non- specified parts.

This makes it easy to hear all of the sound track when watching movies at night at low levels.

1

While the digital signals from the Dolby

• Each time the MULTI CONTROL knob is rotated,

Digital program source are being input.

the compression rate changes as follows:

 

 

 

 

 

 

 

 

 

 

 

 

 

• In some Dolby Digital software, this function may

 

 

 

not be available.

“DYNAMIC : ~” is displayed for several seconds.

If the dynamic range mode disappears, start again from the above step .

Operating the sleep timer

 

Adjusting the brightness of the

• The sleep timer allows the system to continue to

fluorescent displays

 

 

 

operate for a specified period of time before

 

 

automatically shutting off.

 

 

 

• To set the receiver to automatically turn off after the

 

 

specified period of time.

 

 

STANDBY

POWER ON

 

 

 

AUD2

 

 

 

 

SLEEP

D/A

 

 

 

DIMM

S.A/B

STANDBY

POWER ON

 

ROOM2

SUR.B

 

 

 

AUD2

 

 

T.TON

PURE

 

 

 

 

SLEEP

D/A

 

OSD

PARA.

DIMM

S.A/B

 

PAGE1

 

 

 

ROOM2

SUR.B

 

 

 

T.TON

PURE

 

 

 

OSD

PARA.

 

 

 

PAGE1

 

 

 

• Each time this button is pressed, the sleep time

• Each time this button is pressed, the brightness of all

changes and disappears in several seconds as follows:

fluorescent displays of Sherwood components

10 20 30 60

90 OFF

 

connected by the DIGI LINK III changes together as

Unit : minutes

 

follows:

 

• While operating the sleep timer, “

” lights up.

ON dim OFF

 

 

 

• When the sleep time is selected,

 

• In the display OFF mode, pressing any button will

all display panels of Sherwood components connected

restore the display ON mode.

by the DIGI LINK III are dimly lit.

 

 

 

ENGLISH

40

Image 40
Contents 965 Introduction Read this Before Operating Your UnitSafety Instruction Contents Connecting Antennas System ConnectionsConnecting Audio Components Component video input default settings Digital input default settings USB audio connectionConnecting 8CH Direct INs Surround speakers a and B Surround back speakersSpeaker placement Front left and right speakers and center speakerConnecting System Control Room 2 connectionsConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Front Panel Controls Dolby PL II Music ParameterFluorescent Display Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons TapePlay PLAY/PAUSE Loading Batteries AUD1Entering a Setup Code Enter the 3 digit setup code aiming Room 2 Remote Controls Remote Control Operation RangeListening to a Program Source OperationsBefore operation When CD, AUX or Video 1~ Video 6 is selected Adjusting the tone bass and trebleAchieving higher purity of sound quality Muting the sound Listening with the headphonesCompensating for edgy or shrill movie sound tracks Surround Sound Surround modesTheater Front L/R Center Select the desired surround mode Enjoying Surround SoundTo listen in a Dolby Pro Logic IIx mode 2CH downmix modeTo listen in a Dolby Virtual Speaker mode Selecting the surround back channel mode as connected To listen in a Dolby Headphone modeAdjusting each channel level with test tone Adjusting the current channel levelsAdjust the level of the selected channel as Desired Manual tuning Auto tuningAuto presetting Manual presetting Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness Other FunctionsCompressing the dynamic range Dolby Digital sources onlyEntering a label Correcting or clearing a labelRoom 2 Source Playback Press the Room 2 buttonOSD Menu Settings Using the OSDCurrent Status Display When selecting the Power AMP Assign Setting the Speaker Setup Setting the Power AMP AssignWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance When selecting the Virtual Speaker Setup Virtual Speaker mode changes as followsWhen selecting the Subwoofer When selecting the Subwoofer Mode When selecting the Crossover FrequencyWhen selecting the Auto Speaker Setup PreparationsDB , S , 1 0 f t Setting the System Setup When selecting the Digital Input SetupWhen Cinema EQ mode is selected When selecting the Tone ControlWhen Tone Defeat mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup VideoWhen selecting the Video 2 OUT When selecting the DC Trigger 2 SetupWhen the DC Trigger 2 mode is set to On When selecting the Digital RE-MASTERINGWhen selecting the A/V Sync Setting the Surround Setup When Decoding Mode is selectedWhen thez Dolby surround mode is selected When the Surround Mode is selectedWhen the Dynamic Range is selected When selecting the Center Width control When selecting the Panorama modeWhen selecting the Dimension control When selecting the Preset 1 or Setting the CH Level SetupWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Room 2 Feed mode When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section965