Sherwood R-965 manual Using the OSD, OSD Menu Settings, Current Status Display

Page 43

ENGLISH

Using the OSD

This unit incorporates an OSD(On-screen display) function to provide information about basic operation of this unit and to simplify the setup procedures.

The OSD function uses a monitor TV connected to this unit as a display and has two kinds of display modes such as current status display and menu screen.

Notes

•Any on-screen display shown on the monitor TV will not be recorded.

•Because this unit cannot support the OSD function for the progressively scanned video signal, the OSD for current status and menu settings may be displayed abnormally or may not be displayed.

CURRENT STATUS DISPLAY

This mode shows the status corresponding to each operation.

•The on-screen display will automatically disappear in several seconds.

•For examples, there are 2 status displays as follows.

Notes :

•When watching a movie earnestly, if you want to turn off the current status display function, set the OSD auto display mode to Off.(For details, refer to “When selecting the OSD AUTO DISPLAY” on page 55.)

Current status display function might not operate as expected if :

•You view a movie via MONITOR COMPONENT OUTs while component video signals are input into this receiver.

•You view a movie via MONITOR COMPOSITE OUT while S-Video signals and composite video signals are input into this receiver.

When selecting the desired input source.

VIDEO 1 (OPTICAL 1)

Input source

Signal input

When selecting the TEST TONE mode.

Channel level or

FL : ------

------ : 0 dB

 

overall volume display

 

•When adjusting overall volume, the volume level display will be shown.

•The test tone display will be shown until the test tone mode is canceled.

OSD Menu Settings

•The OSD menu allows you to perform the setup procedures easily. In most situations, you will only need to set this once during the installation and layout of your home theater, and it rarely needs to be changed later. The OSD menu consists of 6 main menus: power amp assign, speaker setup, system setup, surround setup, CH level setup and room 2 feed setup. Some of these menus are divided into various sub-menus.

•The OSD menu settings are performed easily with the CURSOR control(, , , ), OSD, RETURN and ENTER buttons.

Notes:

•In such a case of making only COMPONENT VIDEO connections between this receiver and video component, while viewing a movie via the MONITOR COMPONENT OUTs, if the OSD menu operation is performed, the picture is automatically turned off and only the OSD menu is displayed.

•When S-Video signals and composite video signals are input into this receiver, even though the OSD menu operation is performed, the OSD menu cannot be displayed via MONITOR COMPOSITE OUT.

Turn the menu screen on.

1

PAGE

MAIN

FAV

VOL

 

 

1

2

3

OSD/MENU

4

5

6

 

7

8

9

ENT

 

0

 

MI

M2

M3

 

•The main menu will be shown.

•To turn the menu screen off, press this button again.

M A I N

M E N U

P OWE R A MP A S S I G N

S P E A K E R

S E T U P

S Y S T E M

S E T U P

S U R R O U N D

S E T U P

C H L E V E L

S E T U P

R O O M 2 F E E D S E T U P

 

, : M o v e

O S D : Q u i t

E N T E R : S e l e c t

 

 

•In the bottom of the display, “OSD” stands for the OSD button,

“RETURN” for “RETURN”, “ENTER” for “ENTER”, “ ”,

“”, “” and “ ” for CURSOR UP(), DOWN( ), LEFT() and RIGHT().

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents 965 Read this Before Operating Your Unit IntroductionSafety Instruction Contents System Connections Connecting AntennasConnecting Audio Components Component video input default settings USB audio connection Digital input default settingsConnecting 8CH Direct INs Surround back speakers Surround speakers a and BFront left and right speakers and center speaker Speaker placementRoom 2 connections Connecting System ControlConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Dolby PL II Music Parameter Front Panel ControlsFluorescent Display Digi Link system remote controls Universal Remote ControlsTape Function Table of the Numbered ButtonsPlay PLAY/PAUSE AUD1 Loading BatteriesEntering a Setup Code Enter the 3 digit setup code aiming Remote Control Operation Range Room 2 Remote ControlsListening to a Program Source OperationsBefore operation Adjusting the tone bass and treble When CD, AUX or Video 1~ Video 6 is selectedAchieving higher purity of sound quality Muting the sound Listening with the headphonesCompensating for edgy or shrill movie sound tracks Surround modes Surround SoundTheater Front L/R Center Enjoying Surround Sound Select the desired surround modeTo listen in a Dolby Pro Logic IIx mode 2CH downmix modeTo listen in a Dolby Virtual Speaker mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connectedAdjusting the current channel levels Adjusting each channel level with test toneAdjust the level of the selected channel as Desired Manual tuning Auto tuningAuto presetting Tuning to preset stations Manual presettingListening to FM stereo broadcasts Scanning preset stations in sequenceDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorDigital Audio Recording with MD Recorder Dolby Digital sources only Operating the sleep timer Adjusting the brightnessOther Functions Compressing the dynamic rangeCorrecting or clearing a label Entering a labelPress the Room 2 button Room 2 Source PlaybackOSD Menu Settings Using the OSDCurrent Status Display When selecting the Power AMP Assign Setting the Speaker Setup Setting the Power AMP AssignWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance Virtual Speaker mode changes as follows When selecting the Virtual Speaker SetupWhen selecting the Subwoofer When selecting the Crossover Frequency When selecting the Subwoofer ModePreparations When selecting the Auto Speaker SetupDB , S , 1 0 f t When selecting the Digital Input Setup Setting the System SetupWhen Cinema EQ mode is selected When selecting the Tone ControlWhen Tone Defeat mode is selected When selecting the Current Video When selecting the OSD Auto DisplayVideo When selecting the Component Video SetupWhen selecting the DC Trigger 2 Setup When selecting the Video 2 OUTWhen selecting the Digital RE-MASTERING When the DC Trigger 2 mode is set to OnWhen selecting the A/V Sync When Decoding Mode is selected Setting the Surround SetupWhen thez Dolby surround mode is selected When the Surround Mode is selectedWhen the Dynamic Range is selected When selecting the Center Width control When selecting the Panorama modeWhen selecting the Dimension control When selecting the Preset 1 or Setting the CH Level SetupWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Room 2 Feed modeProblem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications965
Top Page Image Contents