Sherwood R-965 When the DC Trigger 2 mode is set to On, When selecting the Digital RE-MASTERING

Page 58

Continued

When the DC TRIGGER 2 mode is set to On

Press the CURSOR UP()/DOWN()/LEFT()/RIGHT() buttons to select the desired input

3 source that uses the DC trigger 2 function, then press the ENTER button.

ENGLISH

PAGE

MAIN

FAV

VOL

 

 

1 2 3

4 5 6

7 8 9

0

MI M2 M3

RNC-510

Each time the CURSOR CONTROL buttons are

pressed, “” is moved to the corresponding input source.

When the ENTER button is pressed at the desired input source, “+” is marked it with.

When the input sources marked with “+” on this menu are selected with the AUDIO and VIDEO SELECTOR buttons, etc.,the DC trigger function is automatically activated. (For details, refer to “CONNECTING DC TRIGGER OUTs” on page 12.)

When the ENTER button is pressed at the input source marked with “+”, “+” is cleared and the DC trigger 2 function is canceled for this input source.

Repeat this step until the desired input sources are all selected.

When selecting the DIGITAL RE-MASTERING

Press the CURSOR UP( )/DOWN( ) buttons to select the DIGITAL RE-MASTERING.

1

PAGE

MAIN

FAV

VOL

 

 

1

2

3

4

5

6

7

8

9

 

0

 

MI

M2

M3

Press the CURSOR LEFT( )/RIGHT( ) buttons to select the desired mode.

2

PAGE

MAIN

FAV

VOL

 

 

1 2 3

4 5 6

7 8 9

0

MI M2 M3

RNC-510

Each time these buttons are pressed, the digital re- mastering mode changes as follows:

On : Select this to process the input signal digitally and to convert its sampling frequency to 192 kHz for an more detailed sound reproduction.

Off : Select this to cancel the digital re-mastering function.

Notes :

The digital re-mastering function does affect on the front left and right signals only.

However, it does not affect on the digital signals that are output from the DIGITAL OUTs of this unit.

When the stereo mode or the pure audio function is selected while playing analog stereo sources, the digital re- mastering function cannot be activated.

58

Image 58
Contents 965 Introduction Read this Before Operating Your UnitSafety Instruction Contents Connecting Antennas System ConnectionsConnecting Audio Components Component video input default settings Digital input default settings USB audio connectionConnecting 8CH Direct INs Surround speakers a and B Surround back speakersSpeaker placement Front left and right speakers and center speakerConnecting System Control Room 2 connectionsConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Front Panel Controls Dolby PL II Music ParameterFluorescent Display Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons TapePlay PLAY/PAUSE Loading Batteries AUD1Entering a Setup Code Enter the 3 digit setup code aiming Room 2 Remote Controls Remote Control Operation RangeListening to a Program Source OperationsBefore operation When CD, AUX or Video 1~ Video 6 is selected Adjusting the tone bass and trebleAchieving higher purity of sound quality Muting the sound Listening with the headphonesCompensating for edgy or shrill movie sound tracks Surround Sound Surround modesTheater Front L/R Center Select the desired surround mode Enjoying Surround SoundTo listen in a Dolby Pro Logic IIx mode 2CH downmix modeTo listen in a Dolby Virtual Speaker mode Selecting the surround back channel mode as connected To listen in a Dolby Headphone modeAdjusting each channel level with test tone Adjusting the current channel levelsAdjust the level of the selected channel as Desired Manual tuning Auto tuningAuto presetting Manual presetting Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Compressing the dynamic range Operating the sleep timer Adjusting the brightnessOther Functions Dolby Digital sources onlyEntering a label Correcting or clearing a labelRoom 2 Source Playback Press the Room 2 buttonOSD Menu Settings Using the OSDCurrent Status Display When selecting the Power AMP Assign Setting the Speaker Setup Setting the Power AMP AssignWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance When selecting the Virtual Speaker Setup Virtual Speaker mode changes as followsWhen selecting the Subwoofer When selecting the Subwoofer Mode When selecting the Crossover FrequencyWhen selecting the Auto Speaker Setup PreparationsDB , S , 1 0 f t Setting the System Setup When selecting the Digital Input SetupWhen Cinema EQ mode is selected When selecting the Tone ControlWhen Tone Defeat mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup VideoWhen selecting the Video 2 OUT When selecting the DC Trigger 2 SetupWhen the DC Trigger 2 mode is set to On When selecting the Digital RE-MASTERINGWhen selecting the A/V Sync Setting the Surround Setup When Decoding Mode is selectedWhen thez Dolby surround mode is selected When the Surround Mode is selectedWhen the Dynamic Range is selected When selecting the Center Width control When selecting the Panorama modeWhen selecting the Dimension control When selecting the Preset 1 or Setting the CH Level SetupWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Room 2 Feed mode When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section965