Sherwood R-965 manual Entering a Setup Code

Page 21

ENGLISH

ENTERING A SETUP CODE

This remote control can control up to ten different components.

Before operating audio and video components using the remote control supplied with this receiver, the setup code for each component should be entered.

For system remote control operation between Sherwood components , “001” was stored previously in the memory of each device such as “AUD 1” and “AUD 2” for this receiver, “CD” for CD player, “TAPE” for tape deck, “TV” for TV and “DVD” for DVD player.

So, you don’t need to enter its code for each Sherwood component except in such a case that its code does not work.(When entering each setup code for Sherwood CD player and tape deck, do from the below step .)

Turn on the component you want to control.

1

Note:

If your component has the discrete POWER ON and OFF(STADNBY) buttons, please do not turn on the component manually.

Example) When entering the setup code for this receiver, turn off this receiver.

Press both the MAIN and OSD/MENU

3

seconds.(/ENTER) buttons simultaneously for 3

 

STANDBY

 

POWER ON

 

 

 

MAIN

 

PAGE

MAIN

FAV

VOLCH/

 

DECODE

DSP

DSP

RETURN

STEREO

1 2 3

4

5

6

OSD/MENU

7

8

9

 

 

OSD/MENU

 

DISP

0

ENT

ENT

MI

M2

M3

 

RNC-510

 

 

Then the setup menu will be displayed on the LCD screen.

Note:

• If the display of the corresponding mode disappears, start again from the above step or the current mode.

Select the device corresponding to the

5 component you want to control.

Example) When selecting the “AUD 1” for this receiver or amplifier, etc.

STANDBY

POWER ON

P-PRO

AUD1 AUD2

CD TV

DVD VCR

TAPE SAT

AUX CABLE

SELECT

Find the setup code for your component

2 referring to “Set-Up Code Table” in the operating manual of this remote control.

Example) The 3 digit setup codes for the Sherwood “Audio” are 001,024, ...(Hint:The correct setup code for this receiver is “001”.)

Select the Pre-PROgramming mode.

4

STANDBY

POWER ON

SETUP

P-PRO LEARN

FAV MACRO

PUNCH RECAL

ERASE EDIT

LIGHT CLONE

• Then the Pre-PROgramming menu will be displayed.

Select the device from which the appropriate

6 3 digit setup code table will be selected. Example) If it is the “AUD 1” code table,

select the “AUD 1”.

STANDBYPOWER ON

AUD1

 

AUD1

 

AUD1

AUD2

001

SAVE

 

 

CD

TV

 

 

DVD

VCR

 

 

TAPE

SAT

 

EXIT

 

 

AUX

CABLE

 

 

TABLE

DOWN

UP

ENTER

21

Image 21
Contents 965 Read this Before Operating Your Unit IntroductionSafety Instruction Contents System Connections Connecting AntennasConnecting Audio Components Component video input default settings USB audio connection Digital input default settingsConnecting 8CH Direct INs Surround back speakers Surround speakers a and BFront left and right speakers and center speaker Speaker placementRoom 2 connections Connecting System ControlConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Dolby PL II Music Parameter Front Panel ControlsFluorescent Display Digi Link system remote controls Universal Remote ControlsTape Function Table of the Numbered ButtonsPlay PLAY/PAUSE AUD1 Loading BatteriesEntering a Setup Code Enter the 3 digit setup code aiming Remote Control Operation Range Room 2 Remote ControlsOperations Listening to a Program SourceBefore operation Adjusting the tone bass and treble When CD, AUX or Video 1~ Video 6 is selectedMuting the sound Listening with the headphones Achieving higher purity of sound qualityCompensating for edgy or shrill movie sound tracks Surround modes Surround SoundTheater Front L/R Center Enjoying Surround Sound Select the desired surround mode2CH downmix mode To listen in a Dolby Pro Logic IIx modeTo listen in a Dolby Virtual Speaker mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connectedAdjusting the current channel levels Adjusting each channel level with test toneAdjust the level of the selected channel as Desired Auto tuning Manual tuningAuto presetting Tuning to preset stations Manual presettingListening to FM stereo broadcasts Scanning preset stations in sequenceRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timer Adjusting the brightnessCompressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a label Entering a labelPress the Room 2 button Room 2 Source PlaybackUsing the OSD OSD Menu SettingsCurrent Status Display When selecting the Power AMP Assign Setting the Power AMP Assign Setting the Speaker SetupWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance Virtual Speaker mode changes as follows When selecting the Virtual Speaker SetupWhen selecting the Subwoofer When selecting the Crossover Frequency When selecting the Subwoofer ModePreparations When selecting the Auto Speaker SetupDB , S , 1 0 f t When selecting the Digital Input Setup Setting the System SetupWhen selecting the Tone Control When Cinema EQ mode is selectedWhen Tone Defeat mode is selected When selecting the Current Video When selecting the OSD Auto DisplayVideo When selecting the Component Video SetupWhen selecting the DC Trigger 2 Setup When selecting the Video 2 OUTWhen selecting the Digital RE-MASTERING When the DC Trigger 2 mode is set to OnWhen selecting the A/V Sync When Decoding Mode is selected Setting the Surround SetupWhen the Surround Mode is selected When thez Dolby surround mode is selectedWhen the Dynamic Range is selected When selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dimension control Setting the CH Level Setup When selecting the Preset 1 orWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Room 2 Feed modeProblem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications965