Sherwood R-965 manual System Connections, Connecting Antennas

Page 5

ENGLISH

System Connections

Pleas be certain that this unit is unplugged from the AC outlet before making any connections.

Since different components often have different terminal names, carefully read the operating instructions of the component connected.

Be sure to observe the color coding when connecting audio, video and speaker cords.

Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the unit.

3

12

8

1

14

9

10 11

4,12

7

 

 

 

 

 

7

SER. NO

 

 

 

 

 

 

6

5

4

2

3

5

13

1. CONNECTING ANTENNAS

FM Indoor Antenna

FM Outdoor Antenna

Change the position of the FM indoor antenna until you get the best reception of your favorite FM stations.

AM Loop Antenna

Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set it to a direction for the best reception.

If the reception is poor with the AM loop anten- na, an AM outdoor antenna can be used in place of the AM loop antenna.

A 75outdoor FM antenna may be used to fur- ther improve the reception. Disconnect the indoor antenna before replacing it with the outdoor one.

AM Outdoor Antenna

AM Loop Antenna

5

Image 5
Contents 965 Read this Before Operating Your Unit IntroductionSafety Instruction Contents System Connections Connecting AntennasConnecting Audio Components Component video input default settings USB audio connection Digital input default settingsConnecting 8CH Direct INs Surround back speakers Surround speakers a and BFront left and right speakers and center speaker Speaker placementRoom 2 connections Connecting System ControlConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Dolby PL II Music Parameter Front Panel ControlsFluorescent Display Digi Link system remote controls Universal Remote ControlsTape Function Table of the Numbered ButtonsPlay PLAY/PAUSE AUD1 Loading BatteriesEntering a Setup Code Enter the 3 digit setup code aiming Remote Control Operation Range Room 2 Remote ControlsBefore operation OperationsListening to a Program Source Adjusting the tone bass and treble When CD, AUX or Video 1~ Video 6 is selectedCompensating for edgy or shrill movie sound tracks Muting the sound Listening with the headphonesAchieving higher purity of sound quality Surround modes Surround SoundTheater Front L/R Center Enjoying Surround Sound Select the desired surround modeTo listen in a Dolby Virtual Speaker mode 2CH downmix modeTo listen in a Dolby Pro Logic IIx mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connectedAdjusting the current channel levels Adjusting each channel level with test toneAdjust the level of the selected channel as Desired Auto presetting Auto tuningManual tuning Tuning to preset stations Manual presettingListening to FM stereo broadcasts Scanning preset stations in sequenceRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timer Adjusting the brightnessCompressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a label Entering a labelPress the Room 2 button Room 2 Source PlaybackCurrent Status Display Using the OSDOSD Menu Settings When selecting the Power AMP Assign When selecting the Speaker Configuration Setting the Power AMP AssignSetting the Speaker Setup Each time these buttons are pressed, and are When selecting the Speaker Distance Virtual Speaker mode changes as follows When selecting the Virtual Speaker SetupWhen selecting the Subwoofer When selecting the Crossover Frequency When selecting the Subwoofer ModePreparations When selecting the Auto Speaker SetupDB , S , 1 0 f t When selecting the Digital Input Setup Setting the System SetupWhen Tone Defeat mode is selected When selecting the Tone ControlWhen Cinema EQ mode is selected When selecting the Current Video When selecting the OSD Auto DisplayVideo When selecting the Component Video SetupWhen selecting the DC Trigger 2 Setup When selecting the Video 2 OUTWhen selecting the Digital RE-MASTERING When the DC Trigger 2 mode is set to OnWhen selecting the A/V Sync When Decoding Mode is selected Setting the Surround SetupWhen the Dynamic Range is selected When the Surround Mode is selectedWhen thez Dolby surround mode is selected When selecting the Dimension control When selecting the Panorama modeWhen selecting the Center Width control When selecting the Preset 1 Trim or Preset 2 Trim Setting the CH Level SetupWhen selecting the Preset 1 or When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Room 2 Feed modeProblem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications965