Sherwood R-965 manual Connecting MULTI-ROOM System KIT

Page 13

ENGLISH

10. CONNECTING MULTI-ROOM SYSTEM KIT

The multi-room system kit(sold separately ) is essential for operation from a remote location .

For information on the multi-room system kit, contact the Xantech corporation at 1-800-843-5465 or www.xantech.com.

IR IN jack allow you to control this receiver from another room with the remote control unit.

To control this receiver from another room with the remote control unit, connect the IR IN jack to the output of the connecting block.

If this receiver is located inside a cabinet or other enclosure where the infrared beams from the remote control unit cannot enter, then operation with the remote control unit will not be possible. In such a case, connect the IR IN jack to the output of the connecting block.

To control other compatible component from another room with the universal remote control unit, connect the IR OUT jack to the IR emitter.

Note:

Remote operation may become unreliable if the IR receiver is exposed to strong light such as direct sunlight or inverted fluorescent.

Main room

Another room(Room 2)

 

Connecting block

 

 

(Multi-room system kit)

 

 

output

 

 

 

IR receiver

 

 

(Multi-room system kit)

This receiver

DVD player

 

 

IR emitter

 

 

(Multi-room system kit)

 

When this receiver is located inside a cabinet.

In the cabinet

output

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connecting block

IR receiver

(Multi-room system kit)

(Multi-room system kit)

This receiver

11. CONNECTING MICROPHONE

To use Auto Speaker Setup function, connect the supplied microphone to the SETUP MIC jack.(For details, refer to

“When selecting the AUTO SPEAKER SETUP” on page 51.)

Notes:

• Because the microphone for Auto Speaker Setup is

designed for use with this receiver, do not use a

Microphone

 

microphone other than the one supplied with this receiver.

 

After you have completed the auto speaker setup procedure, disconnect the microphone.

13

Image 13
Contents 965 Read this Before Operating Your Unit IntroductionSafety Instruction Contents System Connections Connecting AntennasConnecting Audio Components Component video input default settings USB audio connection Digital input default settingsConnecting 8CH Direct INs Surround back speakers Surround speakers a and BFront left and right speakers and center speaker Speaker placementRoom 2 connections Connecting System ControlConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Dolby PL II Music Parameter Front Panel ControlsFluorescent Display Digi Link system remote controls Universal Remote ControlsTape Function Table of the Numbered ButtonsPlay PLAY/PAUSE AUD1 Loading BatteriesEntering a Setup Code Enter the 3 digit setup code aiming Remote Control Operation Range Room 2 Remote ControlsListening to a Program Source OperationsBefore operation Adjusting the tone bass and treble When CD, AUX or Video 1~ Video 6 is selectedAchieving higher purity of sound quality Muting the sound Listening with the headphonesCompensating for edgy or shrill movie sound tracks Surround modes Surround SoundTheater Front L/R Center Enjoying Surround Sound Select the desired surround modeTo listen in a Dolby Pro Logic IIx mode 2CH downmix modeTo listen in a Dolby Virtual Speaker mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connectedAdjusting the current channel levels Adjusting each channel level with test toneAdjust the level of the selected channel as Desired Manual tuning Auto tuningAuto presetting Tuning to preset stations Manual presettingListening to FM stereo broadcasts Scanning preset stations in sequenceRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timer Adjusting the brightnessCompressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a label Entering a labelPress the Room 2 button Room 2 Source PlaybackOSD Menu Settings Using the OSDCurrent Status Display When selecting the Power AMP Assign Setting the Speaker Setup Setting the Power AMP AssignWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance Virtual Speaker mode changes as follows When selecting the Virtual Speaker SetupWhen selecting the Subwoofer When selecting the Crossover Frequency When selecting the Subwoofer ModePreparations When selecting the Auto Speaker SetupDB , S , 1 0 f t When selecting the Digital Input Setup Setting the System SetupWhen Cinema EQ mode is selected When selecting the Tone ControlWhen Tone Defeat mode is selected When selecting the Current Video When selecting the OSD Auto DisplayVideo When selecting the Component Video SetupWhen selecting the DC Trigger 2 Setup When selecting the Video 2 OUTWhen selecting the Digital RE-MASTERING When the DC Trigger 2 mode is set to OnWhen selecting the A/V Sync When Decoding Mode is selected Setting the Surround SetupWhen thez Dolby surround mode is selected When the Surround Mode is selectedWhen the Dynamic Range is selected When selecting the Center Width control When selecting the Panorama modeWhen selecting the Dimension control When selecting the Preset 1 or Setting the CH Level SetupWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Room 2 Feed modeProblem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications965