Sherwood R-965 When CD, AUX or Video 1~ Video 6 is selected, Adjusting the tone bass and treble

Page 25

ENGLISH

When CD, AUX or VIDEO 1~ VIDEO 6 is selected

Select the digital or the analog input as

4 desired.

	STANDBY	POWER ON
	AUD2
	SLEEP	D/A
	DIMM	S.A/B
or	ROOM2	SUR.B
or	T.TON	PURE
	OSD	PARA.

PAGE1

•Each time this button is pressed, the corresponding input is selected as follows:

DIGITAL ANALOG

•When PHONO, TUNER or TAPE MONITOR is selected as an input source, the analog input is automatically selected.

Notes:

•When the selected digital input is not connected, “DIGITAL” is flickering, meaning no sound.(Refer to “ENJOYING SURROUND SOUND” on page 30.)

•To select the digital input, you should assign the connected DIGITAL IN to the corresponding input source. (For details, refer to “When selecting the DIGITAL INPUT SETUP” on page 53.)

Operate the selected component for

5 playback.

•When playing back the program sources with surround sound, refer to “ENJOYING SURROUND SOUND” on page 30.

Adjust the (overall) volume.

6

MAIN

	or	VOL	VOL
DOWN	UP		1	2	3
DOWN	UP		4	5	6
			7	8	9
				0
			MI	M2	M3

Adjusting the tone (bass and treble)

Select the tone mode as desired.

7

•Each time this button is pressed, the tone mode changes as follows:

BASS TREBLE DEFEAT OFF(or ON)

•The tone display is shown for several seconds.

•If the tone display disappears, press the TONE MODE button again.

•( ) : When the tone defeat function is activated (“DEFEAT ON”), bass and treble modes

cannot be selected Note:

•When the pure audio function is activated, the tone mode cannot be selected.

At the desired tone mode, adjust as

8 desired.

At the tone defeat mode, each time the MULTI CONTROL knob is rotated, the tone defeat mode changes as follows:

DEFEAT ON : When listening to a program source

without the tone effect.

DEFEAT OFF : When adjusting the tone for your taste.

At the desired tone (bass or treble), each time the MULTI CONTROL knob is rotated, the tone level can be adjusted within the range of +10~ -10 dB.

•In general, we recommend the bass and treble to be adjusted to 0(flat) level.

•To complete tone adjustment, repeat the above steps

and .

•Extreme settings at high volume may damage your speakers.

25

Image 25

Contents 965 Read this Before Operating Your Unit IntroductionSafety Instruction Contents System Connections Connecting AntennasConnecting Audio Components Component video input default settings USB audio connection Digital input default settingsConnecting 8CH Direct INs Surround back speakers Surround speakers a and BFront left and right speakers and center speaker Speaker placementRoom 2 connections Connecting System ControlConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Dolby PL II Music Parameter Front Panel ControlsFluorescent Display Digi Link system remote controls Universal Remote ControlsTape Function Table of the Numbered ButtonsPlay PLAY/PAUSE AUD1 Loading BatteriesEntering a Setup Code Enter the 3 digit setup code aiming Remote Control Operation Range Room 2 Remote ControlsListening to a Program Source OperationsBefore operation Adjusting the tone bass and treble When CD, AUX or Video 1~ Video 6 is selectedAchieving higher purity of sound quality Muting the sound Listening with the headphonesCompensating for edgy or shrill movie sound tracks Surround modes Surround SoundTheater Front L/R Center Enjoying Surround Sound Select the desired surround modeTo listen in a Dolby Pro Logic IIx mode 2CH downmix modeTo listen in a Dolby Virtual Speaker mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connectedAdjusting the current channel levels Adjusting each channel level with test toneAdjust the level of the selected channel as Desired Manual tuning Auto tuningAuto presetting Tuning to preset stations Manual presettingListening to FM stereo broadcasts Scanning preset stations in sequenceRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timer Adjusting the brightnessCompressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a label Entering a labelPress the Room 2 button Room 2 Source PlaybackOSD Menu Settings Using the OSDCurrent Status Display When selecting the Power AMP Assign Setting the Speaker Setup Setting the Power AMP AssignWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance Virtual Speaker mode changes as follows When selecting the Virtual Speaker SetupWhen selecting the Subwoofer When selecting the Crossover Frequency When selecting the Subwoofer ModePreparations When selecting the Auto Speaker SetupDB , S , 1 0 f t When selecting the Digital Input Setup Setting the System SetupWhen Cinema EQ mode is selected When selecting the Tone ControlWhen Tone Defeat mode is selected When selecting the Current Video When selecting the OSD Auto DisplayVideo When selecting the Component Video SetupWhen selecting the DC Trigger 2 Setup When selecting the Video 2 OUTWhen selecting the Digital RE-MASTERING When the DC Trigger 2 mode is set to OnWhen selecting the A/V Sync When Decoding Mode is selected Setting the Surround SetupWhen thez Dolby surround mode is selected When the Surround Mode is selectedWhen the Dynamic Range is selected When selecting the Center Width control When selecting the Panorama modeWhen selecting the Dimension control When selecting the Preset 1 or Setting the CH Level SetupWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen the Room 2 Feed mode is set to On When selecting the Room 2 Feed modeProblem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications965