Sherwood R-965 manual DB , S , 1 0 f t

Page 52

Continued

Notes:

For your reference, other channel levels displayed are the relative levels as compared with FL channel, not adjusted levels.

Depending on “POWER AMP ASSIGN” and “SUBWOOFER” settings, etc., some channels may be excluded. (For details, refer to “SETTING THE POWER AMP ASSIGN” and “SETTING THE SPEAKER SETUP” on page 45.)

Because the test tones are loud, ensure there no infants or small children in the room.

For best results, ensure the room is as quiet as possible during the auto speaker setup procedure. If there is too much ambient noise, the results may not be satisfactory.

If the results are not satisfactory, you can also personalize your speaker setup and channel level setup by making the settings manually.(For details, refer to “When selecting the SPEAKER CONFIGURATION” on page 45, “When selecting the SPEAKER DISTANCE” on page 47, “Adjusting each channel level with test tone” and “Adjusting the current channel levels” on page 33.)

To confirm the results, press the CURSOR LEFT()/RIGHT() buttons to select the “MEMORY”,

3 then press the ENTER button.

ENGLISH

PAGE

MAIN

FAV

VOL

 

 

1 2 3

4 5 6

7 8 9

0

MI M2 M3

A U T O S P E A K E R S E T U P

S T A R T

F L : 0

dB , L , 1 0 f t

 

 

 

 

 

 

F C : + 4

dB , S , 1 0 f t

 

 

 

 

 

 

F R : 0 dB , L , 1 0 f t

 

 

 

 

 

 

A S R : 1 dB , S , 1 0 f t

 

 

 

 

 

 

B S R :

dB , N ,

f t

 

 

 

 

 

 

 

 

 

 

 

 

B R : + 1 dB , S , 0 9 f t

 

 

 

 

 

 

B L : + 2

dB , S , 0 9 f t

 

 

 

 

 

 

B S L :

dB , N ,

f t

R E T U R N : B a c k E N TER : S e l e c t

Then the results are memorized.

Each time the CURSOR LEFT() or RIGHT() button is pressed, the “MEMORY” or “START” is selected.

However, if error message is displayed, the results cannot be memorized due to incorrect speaker connections, etc.. In this case, turn off the power, check the connections or change speakers as illustrated in error message and then retry the auto speaker setup procedure(, or memorize the result suggested in error message).

52

Image 52
Contents 965 Introduction Read this Before Operating Your UnitSafety Instruction Contents Connecting Antennas System ConnectionsConnecting Audio Components Component video input default settings Digital input default settings USB audio connectionConnecting 8CH Direct INs Surround speakers a and B Surround back speakersSpeaker placement Front left and right speakers and center speakerConnecting System Control Room 2 connectionsConnecting MULTI-ROOM System KIT Connecting PC for Upgrades Front Panel Controls Dolby PL II Music ParameterFluorescent Display Universal Remote Controls Digi Link system remote controlsFunction Table of the Numbered Buttons TapePlay PLAY/PAUSE Loading Batteries AUD1Entering a Setup Code Enter the 3 digit setup code aiming Room 2 Remote Controls Remote Control Operation RangeListening to a Program Source OperationsBefore operation When CD, AUX or Video 1~ Video 6 is selected Adjusting the tone bass and trebleAchieving higher purity of sound quality Muting the sound Listening with the headphonesCompensating for edgy or shrill movie sound tracks Surround Sound Surround modesTheater Front L/R Center Select the desired surround mode Enjoying Surround SoundTo listen in a Dolby Pro Logic IIx mode 2CH downmix modeTo listen in a Dolby Virtual Speaker mode Selecting the surround back channel mode as connected To listen in a Dolby Headphone modeAdjusting each channel level with test tone Adjusting the current channel levelsAdjust the level of the selected channel as Desired Manual tuning Auto tuningAuto presetting Manual presetting Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness Other FunctionsCompressing the dynamic range Dolby Digital sources onlyEntering a label Correcting or clearing a labelRoom 2 Source Playback Press the Room 2 buttonOSD Menu Settings Using the OSDCurrent Status Display When selecting the Power AMP Assign Setting the Speaker Setup Setting the Power AMP AssignWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance When selecting the Virtual Speaker Setup Virtual Speaker mode changes as followsWhen selecting the Subwoofer When selecting the Subwoofer Mode When selecting the Crossover FrequencyWhen selecting the Auto Speaker Setup PreparationsDB , S , 1 0 f t Setting the System Setup When selecting the Digital Input SetupWhen Cinema EQ mode is selected When selecting the Tone ControlWhen Tone Defeat mode is selected When selecting the OSD Auto Display When selecting the Current VideoWhen selecting the Component Video Setup VideoWhen selecting the Video 2 OUT When selecting the DC Trigger 2 SetupWhen the DC Trigger 2 mode is set to On When selecting the Digital RE-MASTERINGWhen selecting the A/V Sync Setting the Surround Setup When Decoding Mode is selectedWhen thez Dolby surround mode is selected When the Surround Mode is selectedWhen the Dynamic Range is selected When selecting the Center Width control When selecting the Panorama modeWhen selecting the Dimension control When selecting the Preset 1 or Setting the CH Level SetupWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Room 2 Feed mode When the Room 2 Feed mode is set to OnTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section965