Bosch Appliances HDS255U, HDS256U, HDS252U Note DO NOT plug in range at this time. Proceed to step

Page 6
Step 4 (cont’d): Connect Electric

Step 4 (cont’d): Connect Electric

4.Connect the Range Cord. Three Wire Connection

The Four Wire Connection is preferred, but where local codes and ordinances permit grounding through neutral, unit may be connected to the power supply via a three wire connection.

1.Disconnect electrical power at breaker box.

2.Remove the terminal block cover to expose the terminal block (See Figure 6).

3.Remove top nut, star washer, and round washer from each post.

Note: DO NOT remove last round washer, last nut or internal wiring leads.

4.Attach white wire, round washer, star washer and nut IN THIS ORDER on top of ground strap on center post. DO NOT remove ground strap. (See Figure 7).

5.Attach red wire, round washer, star washer and nut IN THIS ORDER to left post (See Figure 7).

6.Attach black wire, round washer, star washer and nut IN THIS ORDER to right post (See Figure 7).

7.Tighten all connections securely and replace terminal block cover (See Figure 8).

Figure 6

Black

White

Red

Ground Strap

Figure 7

Four Wire Connection (Preferred Method)

1.Disconnect electrical power at breaker box.

2.Remove the terminal block cover to expose the terminal block (See Figure 6).

3.Remove top nut, star washer, and round washer from each post.

Note: DO NOT remove last round washer, last nut or internal wiring leads.

4.Remove screw from bottom end of ground strap.

5.Remove ground strap from center post, rotate (so that wide end is at top) and straigthen. Then attach wide end to range through hole below terminal block. Attach green wire on top of ground strap. Tighten Screw (See Figure 9).

6.Attach red wire, round washer, star washer and nut IN THIS ORDER to left post (See Figure 10).

7.Attach white wire, round washer, star washer and nut IN THIS ORDER to center post (See Figure 10).

8.Attach black wire, round washer, star washer and nut IN THIS ORDER to right post (See Figure 10).

9.Tighten all connections securely and replace terminal block cover.

Note: DO NOT plug in range at this time. Proceed to step 5.

Black

Ground Strap

White

 

Red

Green Ground Screw

Figure 8

4.Connect the Range Cord. Three Wire ConnectionFour Wire Connection (Preferred Method)Note: DO NOT plug in range at this time. Proceed to step 5.Manual background Green Ground Screw

Green

Ground Strap

Figure 9

Black

White

Red

Page 5

Figure 10

Image 6
Contents Estufa Autoestable de dos Combustibles Installation InstructionsCuisinière à combustion jumelée amovible for Models HDS252U, HDS255U, HDS256UIMPORTANT SAFETY INSTRUCTIONS RANGE TIPPING HAZARD 2. Prepare Cabinets See Figure 1. Install Ventilation3. Install Anti-Tip Bracket Figure 1 Cabinet PreparationStep 4 Connect Electric must be properly installedElectrical Connection Procedures 4. Connect ElectricNote DO NOT plug in range at this time. Proceed to step 4. Connect the Range Cord. Three Wire ConnectionFour Wire Connection Preferred Method Step 4 cont’d Connect ElectricStep 5 Connect Gas Supply Test for Gas LeaksFlame Characteristics Step 6 Test the Installation2. Test/Adjust Flame 1. Test Electric IgnitionPage INSTRUCTIONS DE SÉCURITÉ IMPORTANTES Connexion du gazAVERTISSEMENT RISQUE DE BASCULE 2. Préparation des armoires voir figure 1. Installation de la ventilation3. Installation fixation anti bascule Figure 1 préparation de l’armoire4. Connexion électrique doit être installé adéquatementÉtape 4 Connexion électrique AVERTISSEMENTÉtape 4 suite connexion électrique Connexion à 4 fils recommandéeRemarque NE PAS brancher l’appareil à ce moment. Passer à l’étapes 4. Brancher le cordon de la cuisinière Connexion à trois filÉtape 5 Connexion de l’alimentation en gaz Test pour fuites de gazAller à «Vérifier les fuites de gaz» Caractéristiques de flamme Étape 6 vérifier l’installation1. Test d’allumage électrique 2. Test/réglage de la flammePage INSTRUCCIONES IMPORTANTES DE SEGURIDAD ADVERTENCIA RIESGO DE VOLCADURA DE LA ESTUFA Instaleeldispositivoantivolcaduraquevieneincluido3. Instalar el Soporte Antivolcadura 1. Instalar la Ventilación2. Preparar Gabinetes Vea Figura Figura 1 Preparación de GabinetesCONSEJO Paso 4 Conexión EléctricaADVERTENCIA Se debe instalar correctamente el prensacable quePaso 4 continuación Conexión Eléctrica Nota NO enchufe la estufa en estemomento. Proceda con el paso 4. Conectar el Cable de la EstufaPaso 5 Conectar el Suministro de Gas Verificar Fugas de Gas2. Probar/Ajustar la Llama Paso 6 Probar la Instalación1. Probar el Encendido Eléctrico Características de la Llama