Recorder Connections t, 12V Trigger Connections p

Phono Input Selector Switch q

The Phono input is for a moving magnet (MM) or moving coil (MC) phono cartridge only and is incompatible with line level components. Set the Phono Input Selector Switch as appropri- ate for the phono cartridge you are using. Leave the switch button in the out position for a moving magnet cartridge; push the switch in for a moving coil cartridge.

Some high output moving coil cartridges are designed to operate in the moving magnet position. If you are in doubt about the correct setting, check the instruction manual for your phono cartridge for information regarding its output voltage and the expected input imped- ance. The Phono input has 47 kOhms input impedance and 2.5 mV sensitivity in the MM position and 100 Ohms input impedance and

0.25mV sensitivity in the MC position. If you still have questions about the proper setting of the phono input selector switch, consult your authorized Rotel dealer.

Phono Input e and

Ground w Connection

Plug the cable from the turntable into the ap- propriate left and right phono inputs. If the turntable has a “ground” wire connect it to the screw terminal to the left of the Phono inputs. It will help prevent hum and noise.

Recorder Connections t

The Tape 1 and Tape 2 inputs and outputs can be connected to any record/playback device that accepts standard line level analog input and output signals. Typically that will be a conventional tape recorder.

When connecting a recorder to the RC-1082, remember that the outputs of the recorder must be connected to the tape inputs of the RC-1082. Similarly the tape outputs of the RC-1082 must be connected to the inputs of the recorder. As with other sources be sure to connect the Left and Right channels of each device to the proper channels on the associated components. Use high quality connecting cables to prevent loss of sound quality.

Output Connections u

Most RCA-type output connectors are compat- ible with most power ampliﬁers. As always, use high quality cables and be sure to connect the Left and Right channel outputs of the RC-1082 to the correct channels of the ampliﬁer.

NOTE: There are two sets of RCA outputs on the RC-1082. The second set of outputs may be used in custom system configura- tions to drive a second power amplifier or to supply a signal to a special signal pro- cessor.

12 Volt Trigger Outlet p

Some audio components can be turned on automatically when they receive a 12V turn on “signal”. The 12V Trigger Outputs of RC-1082 provides the required signal. Connect the compatible components to the RC-1082 with a conventional 1/8” miniplug cable. When the RC-1082 is in Standby mode, the trigger signal is interrupted, so the components controlled by it are turned off.

IR Inputs and Outputs

External Remote Input i

This 3.5 mm mini-jack (labeled EXT REM IN) receives command codes from an industry- standard infrared receivers (Xantech, etc.) located in the main listening room. This feature is useful when the unit is installed in a cabinet and the front-panel sensor is blocked. Consult your authorized Rotel dealer for information on external receivers and the proper wiring of a jack to ﬁt the mini-jack receptacle.

NOTE: The IR signals from the EXTERNAL REMOTE IN jack can be relayed to source components using external IR emitters or hard wired connections from the IR OUT jacks.

IR Output o

The IR OUT 1 and 2 jacks send IR signals received at the EXTERNAL REM IN jack to an infrared emitter placed in front of a source component or to other Rotel components with compatible rear panel IR input connectors.

English

This output is used to allow IR signals to pass along IR signals from a remote control when the sensors on the source components are blocked by installation in a cabinet.

See your authorized Rotel dealer for informa- tion on IR repeater systems.

NOTE: The EXT REM IN jack located next to these jacks is for use with an external IR sensor duplicating the front panel IR sensor and located in the primary zone.

12V Trigger Connections p

Many Rotel ampliﬁers offer the option of turn- ing them on and off using a 12 volt trigger signal sent to them. The RC-1082 provides two 12 volt trigger outputs. When the RC-1082 is turned on, a 12 volt DC signal is sent to the ampliﬁers to turn them on. When the RC-1082 is put in STANDBY mode, the trigger signal is interrupted and the ampliﬁers turn off.

To use the remote turn on feature, connect one of the RC-1082 12V TRIGGER OUT jacks to the 12 volt trigger input of a Rotel ampliﬁer, using a cable with mono 3.5 mm mini-plugs on both ends. The +12 V DC signal appears at the “tip” connector.

NOTE: The number “1” 12V trigger signal is turned off when headphones are plugged into the front panel headphone outlet. See the Phones Output section.

Computer I/O Connector y

The RC-1082 can be operated from a personal computer running audio system control software from third-party developers. This control is accomplished by sending the operating codes normally sent by the RR-AT97 remote control over a hard-wired network connection from the computer.

The COMPUTER I/O input provides the neces- sary connection on the back panel. It accepts standard RJ-45 8-pin modular plugs, such as those commonly used in 10-BaseT UTP Ethernet cabling.

For additional information on the connections, software, and operating codes for computer control of the RC-1082, contact your authorized Rotel dealer.

RC-1082 specifications

The Rotel RC-1082 is a prime example of high-fidelity audio engineering, designed for discerning music lovers who crave both versatility and superior sound quality. A key feature of the RC-1082 is its analog preamplification, which delivers a warm and rich audio experience. Utilizing premium components, the device ensures minimal distortion and noise, resulting in an authentic representation of the original sound.

One of the standout characteristics of the RC-1082 is its comprehensive connectivity options. It provides multiple line-level inputs, accommodating a variety of audio sources, including CD players, turntables, and streaming devices. Additionally, the unit includes a home theater bypass function, making it an ideal choice for integrated audio systems. This feature allows for seamless integration with surround sound setups, permitting both high-fidelity audio playback and immersive cinematic experiences.

Rotel has also incorporated proprietary technologies to enhance audio performance in the RC-1082. The unit features a toroidal transformer that delivers stable power to the circuitry, ensuring optimal performance even under demanding conditions. This technology not only improves sound quality but also contributes to the overall efficiency of the device.

In terms of user convenience, the RC-1082 boasts a full-function remote control, enabling easy operation from the comfort of your couch. You can quickly adjust the volume and switch between inputs without the need to get up. The front panel features a clear and intuitive layout, ensuring that adjustments can be made effortlessly.

Another notable aspect of the Rotel RC-1082 is its build quality. Constructed with a robust chassis, the unit minimizes vibrations and external noise interference, which is crucial for maintaining sound accuracy. The premium finishes and sleek design of the device also enhance its aesthetic appeal, making it a stylish addition to any audio setup.

With its combination of flexible connectivity, advanced technologies, and high-quality components, the Rotel RC-1082 stands out as a sophisticated preamplifier for audiophiles. Whether you are listening to a vinyl record or streaming high-resolution music, the RC-1082 ensures a refined audio experience that captures the essence of your favorite performances. Overall, it represents a well-rounded solution for those serious about their audio, offering features that cater to both traditional and modern listening habits.