Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems CSX1200, CSX1000 manual Hardware Installation, PRE-INSTALLATION Requirements

Models: CSX1000 CSX1200

1 644

Download 644 pages 26.85 Kb

Page 63

HARDWARE INSTALLATION

PRE-INSTALLATION REQUIREMENTS

Before you begin the installation process, be sure to:

•Choose a suitable setup location

Make sure the location is dry, ventilated, dust free, static free, and free from corrosive chemicals

• Verify system power requirements

Voltage Range	Current and Frequency

85-264 V	.6 A
	47-63 Hz

The appropriate standard power cord is supplied with the system. The power supply will accept any input voltage from 85 to 264 volts without the need to select a voltage range.

•Verify cabling requirements

The cabling shipped with your system should include:

•BRI/PRI/LAN patch cables, 5 meters each.

•RS232 cable, 1.8 meters. This is for the console port. This cable is a 9-pin female to 9-pin female null modem cable. Jack screws are included.

Note: The BRI/PRI/LAN cables are straight-through CAT5 patch cables. The quantity shipped varies, based on device requirements. These cables are not distinguished from each other in the carton.

We provide a cable for the 10Base-T port since it is typically used for the LAN connection. However, if you plan to use the AUI port instead, you must provide your own cabling and MAU for this connection. If you need additional cabling (other than what was shipped), contact your distributor.

•Verify administration console requirements

In order to install system software, you must have a PC or workstation available. (One is not provided with the system.) This PC or workstation will connect up to the system via the RS232 port. You will also need a communications package that supports terminal emulation software (in order to transfer software to the system).

For details on software installation, refer to the Software Installation chapter.

Image 63

Cabletron Systems CSX1200, CSX1000 Hardware Installation, PRE-INSTALLATION Requirements, Choose a suitable setup location

Contents

USER’S Guide Virus Disclaimer Trademarks DOC Notice Contents Ordering Isdn Service US Only Cfgedit Configuration ToolsSecurity Overview Configuring System Options and Information Configuring Off-node Server Information Configuring Advanced Bridging Configuring Advanced IP Routing Configuring IPX Configuring Snmp Configuring Other Advanced Options System Verification Problem Diagnosis LED Indicators System Messages System Statistics Routine Maintenance Cfgedit Map Using this Guide Cfgedit MAP Documentation SETGuide Conventions Cfgedit ScreensUser’s Guide System Overview CyberSWITCHCyberswitch Network CyberswitchIsdn Unique System FeaturesCyberswitch Interoperability Overview RadiusInteroperability Protocols Interoperability Devices Network Interface Overview Security OverviewSystem Components IsdnRemote Isdn Devices Switches Supported Hardware Overview Safety ConsiderationsCSX1000 and NE Link 1000 a Network Express Product System PlatformsCSX1001, shown below, is equivalent to the NE Link 1000 B2 Workgroup Remote Access Switch System Characteristics EMI CSX1200 CSX1204 BRI Version LAN Access Cabling InformationAUI Pin Signal Function Transmit + Receive + No Connect Basic Rate Interface WAN AccessTransmit Data Pin Signal Function Carrier DetectRing Indicator Receive DataSystem Modules CSX1200-E11-MODSystem Modules CSX1200-U4-MOD System Software Configuration FilesSoftware Overview OverviewOperational Files User Level Security Files Accessing the CyberSWITCH System InstallationWorkgroup Remote Access Switch Ordering BRI Isdn Lines Using Provisioning Settings Ordering Isdn Service US onlyOrdering NI-1 Lines Using EZ-ISDN Codes Ordering NI-1 Lines Using NI-1 Isdn Ordering CodesNI-1 AT&T Custom Point-to-Point Provisioning Settings for AT&T 5ESS SwitchesCSD limit CSD NB limit AT&T 5ESS NI-1 ServiceUnrestricted CSV limit CSV NB limitCSV limit AnyCSD limit Provision Settings for Northern Telecom DMS-100 Switches Number of call Appearances Version Functional YesBasic Information for Ordering PRI Isdn Lines Sprint Type of SwitchDisabled Option Local Bell Operating CompanyVerify administration console requirements Hardware InstallationPRE-INSTALLATION Requirements Choose a suitable setup locationInstalling the CSX1200-E11-MOD Installing the CSX1200-U4-MOD Cabling NULL-MODEM Connection to a PC Accessing the CyberswitchMaking Connections Direct ConnectionChanging the Baud Rate Remote Connection Using a Modem Remote Connection Using TelnetPowering on Establishing AN Administration SessionAdmin Accessing the Release Notes Upgrading System Software Upgrading SoftwareCD File Structure Product Country or Directories Switchtype Upgrading Software Local Software Upgrade This message is displayed Remote Software UpgradeFlash recover Console Messages during SSB Upgrade Change Defaults to Secure System Return Configuration to Factory Defaults Configuring Basic Bridging Basic ConfigurationExecuting Cfgedit Configuration ToolsDynamic Management Saving Cfgedit ChangesExecuting Dynamic Management Saving Dynamic Management Changes Utility Dynamic Management CommandsUsing the Network Worksheets Default ConfigurationUsing the Configuration Chapters Configuring Resources and Lines Configuring Resources Using CfgeditResources United States Resource Background Information Resource Configuration ElementsPPP Lines Configuring Lines Using CfgeditCharacteristic PRI/T1 lines E1 line Multiframe CRCCommonChannel Auto TEI Line Configuration ElementsSwitch Type Number of Data Number of SPIDs Directory NumbersDMS100 custom NI-1 Service Profile ID Spid Robbed Bit Signaling is not supported for the CyberSWITCH Line Background Information Commport InformationSubaddresses Background Information Configuring a Subaddress Using CfgeditSubaddress Configuration Elements SubaddressesMAC Layer Bridging Configuration Elements Configuring Basic BridgingENABLING/DISABLING Bridging Using Cfgedit Select Enable/Disable BridgingMAC Layer Bridging Background Information Configuring Basic IP Routing Enabling IP Using CfgeditInternet Protocol IP Option IP Background Information IP Operating ModeIP Option Configuration Elements Configuring the IP Operating Mode Using CfgeditIP Operating Mode Background Information IP Operating Mode Configuration ElementsIP Network Interfaces Configuring Interfaces Using CfgeditUSER’S Guide Network Interface Configuration Elements MTU Transmit Broadcast IP Address Default switch for numbered WAN interfaces IP RIP Receive Control IP Network Interface Background Information Hdlc Bridge IP Network Interface Type Associated Remote DeviceIP Host RFC1294 WAN Direct Host IP Host RFC1294USER’S Guide Example 1 LAN, WAN and WAN Direct Host Interfaces Example 2 LAN, WAN UnNumbered, WAN Remote LAN Interfaces IP RIP and the IP Network Interfaces Isdn Isdn IP RIP Over Dedicated Connections SITE3 Redundant Configurations for Backup Network FlatteningProxy ARP Example IP Host Communications in Flattened Networks Secondary IP AddressingStatic Routes Configuring Static RoutesIP address for the destination network or host Static Route Configuration Elements Workgroup Remote Access Switch Static Route Background Information IsdnDefault Routes Configuring Default RoutesDefault Route Configuration Elements Routing Information Protocol RIP Option ENABLING/DISABLING IP RIP Using CfgeditLAN IP RIP Configuration ElementsIP RIP Status IP RIP Background InformationSecurity Configuring Security LevelSecurity Level Security OverviewDevice Level Databases System Options and InformationNetwork Login Information User Level DatabasesOFF-NODE Server Information Configuring Security Level On-Node Yes Database Device Level User Level Administration SecurityNo Security Configuring no Security Using CfgeditConfiguring Device Level Security Using Cfgedit Device Level SecurityDevice Level Security Background Information Configuring User Level Security Using Cfgedit User Level SecurityUser Level Security Background Information User Level Security Isdn Making a Telnet Connection Responding to Login PromptsACE Configuring Device and User Level Security Using CfgeditDevice and User Level Security TacacsDevice and User Level Background Information Configuring System Options and Information Configuring System Options Using CfgeditSystem Options System Options System Options Configuration ElementsPAP Chap Bridge MAC Calling Line Id Authentication AddressPAP Chap System Options Background InformationOptional Calling Line Id Configuring System Information Using CfgeditSystem Information Configuration Elements System InformationAdministrative Session Configuring Administrative Sessions Using CfgeditSystem Information Background Information Administrative Session Configuration Elements Administrative Session Background Information Emergency Telnet Server Port Number Background Information Configuring Device Level Databases Configuring AN ON-NODE Device DatabaseON-NODE Device Database ON-NODE Device Entries Configuring ON-NODE Device EntriesOn-node Device Entries No pvc configured for Device DAN SVC 0.0 Routing Device ON-NODE Device Database Configuration Elements DIAL-OUT Phone Numbers Chap Secret Outbound Authentication RIP/SAP Appletalk Information Configuration Elements Bridge Information Configuration Elements Bridging with Hdlc Bridge Devices ON-NODE Device Database Background InformationSecurity Mode On-node Device Table Configuration Data IP Routing with Hdlc Bridge DevicesLine Id IP Routing with PPP IP Devices Using Ipcp IP Routing with IP Host Devices RFC1294PAP or Chap Bridging with PPP Bridge Devices Using BCP PAP Password orIP Routing with PPP Bridge Devices Using BCP OFF-NODE Device Database Location Configuring OFF-NODE Device Database Location Using CfgeditOFF-NODE Device Database Location Background Information OFF-NODE Device Database Location Configuration ElementsConfiguring User Level Databases User Level Authentication Database LocationConfiguring Authentication Database Location Using Cfgedit User Level Authentication Database Location Type communications server Configuring OFF-NODE Server InformationMultiple Administration Login Names Name John Doe Name mynode1 Address Remote Office1Configuring VRA Manager Authentication Server VRA Manager Authentication ServerConfiguring a Radius Authentication Server Radius Authentication ServerVRA Manager Authentication Server Configuration Elements VRA Manager Authentication Server Background InformationDisplays the current Radius server configuration data Radius Authentication Server Background Information Radius Authentication Server Configuration ElementsConfiguring a Tacacs Authentication Server Tacacs Authentication ServerTacacs Authentication Server Background Information Tacacs Authentication Server Configuration ElementsConfiguring AN ACE Authentication Server ACE Authentication ServerACE Authentication Server Configuration Elements ACE Authentication Server Background Information Configuring Network Login Information Network Login General ConfigurationConfiguring General Network Login Information Using Cfgedit Network Login General Configuration Background Information Network Login Banners Configuring Network Login Banners Using CfgeditNetwork Login Banners Background Information Configuring Radius Server Login Information Using Cfgedit Login Configuration Specific to Radius ServerConfiguring Tacacs Server Login Information Using Cfgedit Login Configuration Specific to Tacacs ServerLogin Configuration Specific to Tacacs Server Login Elements Specific to Tacacs Configuring Alternate Accesses Advanced ConfigurationDedicated Access Configuration Elements Configuring Alternate AccessesDedicated Accesses Configuring a Dedicated Access Using CfgeditDedicated Access Background Information Configuring AN X.25 Access AccessesAccesses USER’S Guide Configuration Elements Lapb Configuration Elements Timers Maximum Window Size Nonstandard Default Transmit Window Size PVC Configuration Elements Access Background Information B1 B2 Configuring a Frame Relay Access Frame Relay AccessesConfiguring a PVC Frame Relay General Configuration Elements Dlci Value Frame Relay PVC Configuration ElementsLMI LMI FormatPVC Name Frame Relay Access Background Information Local Management Interface Overview Allowed Not Allowed Bridge Dial OUT Configuring Advanced BridgingUnder ISDN, select Dial Out Phone Number Spanning Tree Protocol Bridge Mode of OperationBridge Mode of Operation Background Information Bridge Filters Configuring Bridge Filters Using CfgeditProtocol Filter Commands Protocol Definition CommandsSource MAC Filter Commands Destination MAC Filter CommandsPacket Data Filter Commands Bridge Filter Configuration ElementsLsap in HEX Bridge Filters Background Information Filter Type Maximum Number of EachFilter Destination MAC Protocol Definitions Source Discard Connect Destination Protocol Packet Unrestricted Mode Bridge FiltersUSER’S Guide Sites connected over the WAN according to Filter Action Distribution Result ListPacket matching this filter will not be forwarded On any LAN port. The packet will be sent to remoteRestricted Mode Forwarding Action Restricted Mode Bridge FiltersWorkgroup Remote Access Switch Any remote sites connected over the WAN Filter Distribution Result Action ListPacket matching this filter will only be forward Ed on the LAN ports. The packet will not be sent toPreliminaries Configuring a Destination MAC Address FilterDiscard Connect Known Connect List Configuring the Known Connect ListKnown Connect List Background Information Known Connect List Configuration ElementsStatic ARP Table Entries Configuring Advanced IP RoutingSelect Static ARP Table Entries from the IP menu Configuring Static ARP Table Entries Using CfgeditStatic ARP Table Entries Configuration Elements Static ARP Table EntriesStatic Route Lookup VIA Radius Isolated ModeIP Address Pool Static Route VIA Radius Configuration ElementsConfiguring AN IP Address Pool Using Cfgedit IP Address Pool Configuration ElementsInitiating the IP Filter Configuration Using Cfgedit IP FiltersIP Address Pool Background Information Configuring Packet Types Using Cfgedit TCP UDP Icpm MaskSpecify a control value any, established, or not established Select Icmp Type Select Add a Forwarding Filter Configuring Forwarding FiltersConfiguring Connection Filters Configuring Exception Filter Select Device Level Databases Select On-node Device Entries Applying FiltersSelect IP Interfaces Select Apply Global Forwarding FilterIP Filters Configuration Elements IP Filters Background Information TCP and UDP PortsNEQ RangeForwarding Filters Packet TypesException Filters Connection FiltersApplication to Network Interfaces Limitations Common PortionFTP WWW Sfvra Example of AN IP Filter ConfigurationForward Dhcp Relay Agent Configuring a Dhcp Relay Agent Using CfgeditDhcp Background Information Dhcp Configuration ElementsRouter to Bridge Environment Bridge to Bridge EnvironmentIP Router to IP Router with Relay Agents on both USER’S Guide Remote Bridge to IP Router w/Relay Agent = WAN Rlan Configuring the Dhcp Proxy Client Dhcp Proxy ClientSelect Dhcp Proxy Client Dhcp Proxy Client ENABLE/DISABLE Flag Sample Configuration IP Router with Dhcp Proxy Client Configuration for IP Router Chloe Configuring IPX Configuring IPX Information ENABLING/DISABLING IPX Using Cfgedit IPX Option Configuration ElementIPX Routing Option IPX Option Background Information Configuring the IPX Internal Network Number Using CfgeditIPX Internal Network Number Configuration Element IPX Internal Network NumberLAN WAN Configuring IPX Network Interfaces Using CfgeditIPX Network Interfaces IPX Network Number Background InformationDisplays the current IPX network interface data IPX Network Interface Configuration Elements SAP IPX Network Interface Configuration Elements IPX Network Interface Background Information Configuring IPX Routing Protocols Using Cfgedit IPX Routing Protocol Configuration ElementsIPX Routing Protocols SAP IPX Routing Protocol Background InformationSpecial Considerations Remote LAN Interface IPX Static Routes Configuring IPX Static Routes Using CfgeditIPX Static Routes Background Information IPX Static Routes Configuration ElementsConfiguring IPX Netware Static Services Using Cfgedit IPX Netware Static ServicesIPX Netware Static Services Configuration Elements IPX Netware Static Services Background Information Configuring IPX Spoofing Using CfgeditIPX Spoofing IPX Spoofing Background Information IPX Spoofing Configuration ElementsWatchdog Protocol IPX Type 20 Packet Handling Configuring IPX Type 20 Packet Handling Using CfgeditIPX Isolated Mode Configuration Elements IPX Isolated ModeIPX Type 20 Packet Handling Configuration Elements Configuring IPX Isolated Mode Using CfgeditDisplaying WAN Peer List IPX Isolated Mode Background InformationConfiguring Triggered RIP/SAP Global Timers Using Cfgedit Configuring IPX Devices IPX-SPECIFIC Information for DevicesTriggered RIP/SAP Background Information IPX-Specific Information for Devices SPX Watchdog Spoofing Menu Enable Bridging and disable Make calls for bridge data IPX Configuration Elements for Devices IPX Background Information for Devices Configuring Snmp Configuring SnmpConfiguring Snmp Snmp Configuration Elements Snmp Background Information WAN Workgroup Remote Access Switch USER’S Guide Configuring Appletalk Routing Enabling Appletalk Routing Using CfgeditAppletalk Routing Option Appletalk Routing Background Information Appletalk Routing Option Configuration ElementConfiguring Appletalk Ports Using Cfgedit Appletalk PortsAppletalk Ports Configuration Elements Appletalk Ports Background Information Overview Considerations ConfigurationConfiguring Appletalk Static Routes Using Cfgedit Appletalk Static RoutesAppletalk Capacities Appletalk Routing Static Routes Configuration ElementsConfiguring Appletalk Capacities Using Cfgedit Appletalk Capacities Configuration ElementsAppletalk Capacities Background Information Appletalk Isolated ModeConfiguring the Appletalk Isolated Mode Using Cfgedit Appletalk Isolated Mode Configuration ElementsConfiguring Call Control Configuring the Throughput Monitor Using CfgeditThroughput Monitor Throughput Monitor Configuration Elements Throughput Monitor Background Information Condition Trigger Number Window Size Utilization90% Overload Condition Monitoring Idle Condition Monitoring Call Interval Background Information Configuring the Call Interval Parameters Using CfgeditCall Interval Configuration Elements Call Interval ParametersMonthly Call Charge Background Information Configuring Monthly Call Charge Using CfgeditMonthly Call Charge Configuration Elements Monthly Call ChargeConfiguring Call Restrictions Using Cfgedit Call Restriction Configuration ElementsCall Restrictions Call Restrictions Call Restrictions Background Information Bandwidth Reservation Configuring Bandwidth Reservation= CentralSite Select Bandwidth Reservation Bandwidth Reservation Configuration ElementsConfiguring Semipermanent Connections Using Cfgedit Semipermanent ConnectionsBandwidth Reservation Background Information Semiperm Semipermanent Connections Configuration Elements Call Device CommandsSemipermanent Connections Background Information Throughput Monitor Call RestrictionsVRA Manager AS a Call Control Manager Configuring VRA Manager for Call Control Using CfgeditBackground Information LIMITATIONS/CONSIDERATIONS Configuring Other Advanced Options PPP ConfigurationConfiguring PPP PPP Configuration Elements PPP Background Information PPP Reference Documents Default Line Protocol Background Information Default Line ProtocolConfiguring Default Line Protocol Using Cfgedit Default Line Protocol Configuration ElementsUDP Port Configuring LOG Options Using CfgeditLOG Options Configuration Elements LOG OptionsLOG Options Background Information CDR LOG Report Overview Call Detail Recording Events Event Report Contents Connect Event Report Contents Disconnect Event Report Contents Reject Event Report ContentsSystem Up Event Report Contents Compression Options Verify Event Report ContentsConfiguring Compression Options Using Cfgedit Compression Options Configuration ElementsCompression Options Background Information Compression and CCP Tftp Configuring TftpTftp Background Information Tftp Configuration ElementsFile Attributes Background Information Configuring File AttributesFile Attributes Configuration Elements File AttributesSTATLOG.1 Users Report Files StatFiles CfgFiles Other FilesFile category File types included in the category RPRTLOG.1System Verification TroubleshootingVerifying Hardware Resources are Operational System VerificationVerifying LAN Connection is Operational Verifying WAN Lines are Available for USEVerifying IP Router is Initialized Verifying Bridge is InitializedVerifying a Frame Relay Connection Verifying a Dedicated ConnectionVerifying AN X.25 Connection Verifying Remote Device ConnectivityVerifying MULTI-LEVEL Security Ping 100.0.0.2 return Verifying IP Host Mode is Operational Verifying IP Host Mode is OperationalVerifying IP Host is Initialized Verifying IP Routing Over a LAN Interface Verifying IP Routing Over InterfacesVerifying IP Routing Over a WAN Interface 100.0.0.1 100.0.0.0 Host B 192.100.1.3 Host a 100.0.0.2 Verifying IP Routing Over a WAN Direct Host Interface Verifying IP Routing Over a WAN Remote LAN Interface Verifying IP Routing Over a WAN Unnumbered Interface Verifying IP RIP is Initialized Verifying IP FiltersVerifying IP RIP Ip filter trace discard returnVerifying IP RIP Output Processing on a LAN Interface Verifying IP RIP Output Processing on a WAN Interface Verifying IP RIP Input Processing on a LAN InterfaceCSX1200 Router Dedicated Connection 100.1.1.1 192.1.1.1 Verifying IPX Routing is Operational Verifying IPX Router is InitializedVerifying IPX Routing Over a LAN Connection Verifying AN IPX Remote LAN ConnectionXxxx Verifying Appletalk Routing is Initialized Verifying the Appletalk Routing FeatureVerifying IPX Routing Over a WAN Connection Verifying Triggered RIP/SAPVerifying Appletalk Routing is Operational Verifying Appletalk Routing Operation Over a WAN Connection Verifying Snmp is Operational Verifying Call Detail Recording Verifying the Dial OUT FeatureVerifying Compression is Operational Verifying Reserved Bandwidth is OperationalVerifying PPP Link Failure Detection is Operational Verifying Dhcp Relay Agent Initialization Verifying Dhcp Relay AgentVerifying the Relay Agent is Operational Verifying the Relay Agent is EnabledVerifying Dhcp Proxy Client Initialization Verifying Dhcp Proxy ClientVerifying the Proxy Client is Enabled Verifying the Proxy Client is OperationalUDP Ports Verifying Proxy ARP is Operational Verifying a Semipermanent ConnectionVerifying Proxy ARP is Operational LAN Adapter Problem DiagnosisGeneral Procedures ProblemBridge Initialization IP Routing InitializationWAN Line Availability Out Svc 1 slot #, port # Frame Relay Connections Dedicated ConnectionsConnections Set-up Remote Device ConnectivityDisabled MULTI-LEVEL SecurityLAN Attachment IP Host Mode IP Host Mode Operation Over the LAN ConnectionIP Host Initialization IP Host Mode Operation Over the WAN Connection IP Routing Over Interface ConnectionsIP Routing Over the LAN Interface Connection IP Routing Over a WAN Interface Connection IP Routing Over a WAN Direct Host Interface Connection IP Routing Over a WAN Rlan Interface Connection IP Routing Over a WAN Unnumbered Interface Connection IP RIP Initialization If you are still experiencing problemsIP RIP Input Processing on a LAN Interface IP RIP Output Processing on a LAN InterfaceIP RIP Input Processing on a WAN Interface IP RIP Output Processing on a WAN InterfaceIPX Routing IPX Routing InitializationIPX Routing Over the LAN Connection IPX Routing Over the Remote LAN Connection IPX Routing Over the WAN Connection IPX Routing and Service Tables Appletalk Routing Triggered RIP/SAP Start UPTriggered RIP/SAP Operation Appletalk Routing Operational Over the LAN Connection Appletalk Routing InitializationUSER’S Guide Appletalk Routing Operational Over the WAN Connection Snmp CyberSWITCH does not generate Snmp Trap PDUs Dial OUT Set UpCall Detail Recording Compression Successful NegotiationPeer Protocol-Rejects CCP CyberSWITCH does not have Compression Enabled Relay Agent InitializationEnabling the Relay Agent Proxy Client Initialization Relay Agent OperationProxy Client Operation Enabling the Proxy ClientProxy ARP Operation Proxy ARP Operation Local Area Network LED Indicators LED IndicatorsPRI LED Indicators Lanview Leds CSX1200-E11-MOD OFF Receive LEDsService Indicator Remains LIT Service IndicatorOUT SVC LAN Xmit Error Service Indicator BlinksAlarm Leds PRI only Alarm LEDs PRI Only Informational Messages System MessagesStatus Messages Boot MessagesInitialization Messages Normal Operation MessagesError Messages System Message SummarySpanning Tree Messages Adapter #’x’ failed to respond from bootstrap Port LAN Adapter, operating in remote mode onlyPort LAN Adapter, operating in local and remote mode Call has exceeded the configured maximum durationAuth ACE Could not write service file Attempting to load FileName for UpgradeAttempt to initialize unconfigured DM card in slot slot # Auth ACE Could not create service fileAuth ACE Node verification received Client initialized Auth ACE Encryption configured for DES not supportedAuth ACE Error receiving server log message acknowledgment Auth ACE Login rejected user user nameAuth Radius PAP rejected device device name Auth Radius Login rejected device device nameAuth Radius IP Host rejected IP Host id IP host Id Auth Radius IP Resolve rejected IP Address IP addressAuth Warning code 0007 Authentication mode mismatch Auth Tacacs Login rejected user user nameAuth Warning code 0001 Timeout Auth Warning code 0004 No authentication node availableBad auth result in smgrauthaanotify for device device name Booting System SoftwareBootstrap came alive on DM card in slot slot # Bootstrap came alive on WAN card in slot slot #Calling Line ID Failure, Duplicate ID calling line Id Call Restrictions have been disabled by user commandCall Restrictions have been enabled by user command Calculating CRC’sCall Restrictions will allow calls to be made Call Restriction statistics reset for new dayCall Restriction statistics reset for new month Call Restrictions will allow calls to be made this hourWorkgroup Remote Access Switch CCP Option Negotiation Failure, Non-Convergence detected Cause cause code received for Dlci dlci indexCause Code Event CCP Internal Decompression FailureChannel in use in Hostcallrequest Chap Authentication Failure remote device not respondingCNTR-TMRTimed out waiting for TMR number interrupt Configured adapter # ’x’ type does not existCouldn’t find speech service slot #, port # Current monthly charges reset for new monthDHCP-P Failed to open UDP port x, erc = y Dedicated connection down slot #, port #DHCP-P Failed to close UDP port x, erc = y DHCP-P Failed to open UDP port for first Dhcp clientDHCP-P Proxy Client initialization failed DHCP-P Proxy Client disabledDHCP-P Proxy Client enabled DHCP-R Relay Agent disabledDHCP-R UDP port 67 opened DHCP-R Relay Agent enabledDHCP-R Relay Agent initialization failed DHCP-R UDP port 67 closedDM upgrade started. Board=board #, Modem=modem # DM card in slot slot # signals it is operationalDM card type configured in slot slot # does not exist DM card in slot slot # will not come out of resetDSL test failed to establish Layer 1, port=port # DM upgrade success. Board=board #, Modem=modem #Downloading Bootstrap to DM card in slot slot # Edrv transmit error error codeError during channel initialization Access access index Error closing file ’s’Error downloading bootstrap program to adapter #’x’ Error downloading operational software to adapter ’x’Error programming adapter #’x’ hardware Error mapping WAN adapter #’x’ into Host memory mapError parsing old WAN Direct Host interface bad format Error opening file \system\ethernt2.binFacility not subscribed Slot=slot # Port=port # Error reading sdconf.rec fileError requesting slot activation Error sending message to Call ControlFailure to allocate enough memory for Xilinx load file Failed to obtain Terminal info in smgrprocterminalauthsessFailure during read of file ’s’ Failure during Static RAM test on adapter # ’x’USER’S Guide Frame Relay event queue full File Access ErrFormatting Flash Memory Frietf detected PPP protocol from NAME, shutting down PVCInitial TDM Clock Master slot#, line# Installing File Set into Flash MemoryInterrupt fault on WAN Adapter in Slot slot # FrUtl No registered device for Dlci dlci indexIP x.x.x.x not added to the pool Unknown error y Invalid Cllm received on Access access indexInvalid Password password given IP Error from ESP datagram discardedIP Cannot get system memory for IP Default Route not added, invalid next hop IP address #IP Invalid configuration for Network Interface dd Ipap ResMem returned invalid device maximum valueIP Network initialized successfully on ddd.ddd.ddd.ddd IP Invalid Peer IP Address IP address, WAN IP Stream ClosedIP IP host is initialized successfully IP IP router is initialized successfullyIP Host Call Dropped XID was not received from remote Ipcp IP Address Pool Out of IP addressesIpcp Option Negotiation Failure, Non-Convergence detected Ipcp Remote device does not negotiate IP addressIP RIP Initialization failed, unable to allocate buffers IP Host Security Rejection Invalid Security ID Id stringIP RIP All network interfaces used IP RIP Buffers allocatedIPX Network initialized successfully on IP RIP Unable to open RIP/UDP portIP RIP Unable to register WAN Connection notification IPX Invalid Ipxwc passedIPX RIP Shutdown complete IPX SAP Space available in service tableIPX SAP Unable to add service, service table full Ipxwan IPX Internal Network Number must be configuredLAN Adapter HW upgrade may be required LAN Adapter Command TimeoutLAN Adapter configuration conflict LAN Adapter Fatal Error ReportedLAN Init Error LAN Adapter ResetLAN Adapter Response Timeout LAN Adapter System resource errorLAN Port port # detected shorted LAN media LAN Xmit ErrorLMI alarm on Access access index LMI alarm reset Access access indexManual restart initiated on DM board in slot slot # Manage Mode updates have been successfully committedMemory Access Timeout Manual intervention required please replace LAN cardNegotiation Failure with Semipermanent device Mismatch of configured and installed DM card in slot slot #Modem modem # of DM card in slot slot # is unusable Modem revision on modem modem # of slot slot # failedNo Active List entry available in INM Network sent Cause Spid not supported slot #, port #Network sent Status with state = 0, tear down call No Active Calls Active SitesOutgoing calls barred Slot=slot # Port=port # Out of LAN Adapter transmit command descriptorsNot enough memory for Security module Offnode server lookup of Dial Out User failedOut Svc # slot # , port # Auto For over 5 minutes Report problem to Phone companyPAP Identification timeout on remote device PAP Invalid password for name given by remote devicePost number, Hdlc #number Internal Loopback Test Failed PAP Remote device rejected System Information error messagePAP Unknown name name given by remote device Post number, Hdlc #number External Loopback Test FailedPVC not allocated for dlci index RBS LIFAddTimer failureRBSoutSMchannel # Timeout waiting for Wink PVC for Dlci dlci index not ActiveReserved signal Reattempting to Install File Set into Flash MemoryRebooting Replace Lithium Battery Contact your RepresentativeSecurity Rejection Caller did not negotiate security Security Rejection Invalid Password password givenRetrying download of DM card in slot slot# in x seconds Rx Channel Inactivity DetectedSecurity Rejection No Protocol List supplied Security Rejection No Password given by callerSecurity Rejection Timeout on Startup Complete Semipermanent. Device x disconnected by adminSnmp Authentication failure, unknown community name Semipermanent. Device x reconnected by adminSignal for unknown CallCmd task task Id Slot #, port # Cfg ErrorSSB i960 Post number not equal to i386’s SSB Post 27 i960timer82c54FAILURESSB Can’t read RTC prior to i960 POSTs SSB Couldn’t read RTC during i960 POSTsSSB Post 31 i960permodmem2 Failure SSB Post 28 i960lan82596sx FailureSSB Post 29 i960lan82503 Failure SSB Post 30 i960permodmem1 FailureSTP a Blan Topology Change has been detected Successfully Loaded Release X.Y Issue ZSwitch could not recognize phone number nnnnnnn System Clock Fault on Wan Adapter in Slot slot #Tftp Local error #5 UDP open failed Tftp Local error #2 Feature not initializedTftp Local error #3 Server not initialized Tftp Local error #4 UDP rejected packet filenameTftp Local error #18 Unable to open file filename Tftp Local error #13 Received unexpected opcode filenameTftp Local error #14 Bad file name Tftp Local error #15 Bad mode stringTftp Remote error # 3 Text from Remote Host Tftp Remote error # 0 Text from Remote HostTftp Remote error # 1 Text from Remote Host Tftp Remote error # 2 Text from Remote HostTimeout on Startup Complete Compression subsystem is not enabledTimeout detected on connection establishment Timeout detected on receiving caller’s numberType mismatch of configured & installed adapter # ’x’ Unable to Decrypt DatagramUnable to get Digital Modem resource to place call Unable to Identify a remote device Unable to open \config\devdb.nei fileUnable to open Modem Upgrade file Unable to restore original ISRs for Interrupt interrupt #WAN card in slot slot # signals it is operational Unexpected error during transmission of LMI frameUnmatched Login Task Updating CyberSWITCH from FileNameX25 facilities error, bad facility length Watchdog timeout detected on DM board in slot slot #Watchdog timeout detected on WAN board ’x’ X25 facilities error, facilities not allowed in PVCX25 facilities error, throughput negotiation not allowed X25 facilities error, reverse charging not acceptedX25 facilities error, fast select not available X25 facilities error, fast select not acceptedZone allocation failed, maximum capacity already configured X25 facilities warning, NUI not availableZone allocation failed, increase zone table capacity Trace Messages Location Causes Call Trace MessagesCall Trace Message Summary Configure ack slot # Inband treatment has been applied-BRD CFG ACK Slot=slot # Init data link slot #, port #, ces Origination call address is non-ISDN Out configure port #Interworking unspecified cause Off-hook warning tone onReceived unknown progress value Received unknown signal valueOut init data link slot #, port # , ces Recall dial tone onIP Filters Trace Messages PPP Packet Trace Messages Configure Reject Configure RequestConfigure ACK Configure NAKTrace Message Summary Trace MessagesEcho Reply Discard RequestX25 DCE RR LCN logical channel number, number of bytes bytes X25 Data LCN logical channel number, number of bytes bytesSystem is sending a call request to the network Lapb Trace Message Summary Lapb Trace MessagesOut Lapb DM Lapb SabmeLapb UA Out Lapb DiscRemote Management System MaintenanceRemote Management SITE.2 Installation and ConfigurationUsage Instructions Telnet Earlier Releases Usage Instructions Tftp Client PC Users Report Files Statistics Files Config files Other Files Remote Installation with USER2 USER’S Guide Accessing Administration Services System CommandsBoot Device Commands Setting the IP AddressViewing Operational Information Accessing Dynamic ManagementList relnote.txt Viewing Operational Information Status Second column is the potential number of connections 100 Viewing Throughput InformationSaving Operational Information Throughput Monitor ContentsClearing Operational Information CONFIGURATION-RELATED CommandsRestarting the Cyberswitch Setting the Date and TimeFile Utility Commands Login-Id Terminating Administration SessionsAppletalk Routing Commands State TypeLAN port Default zoneNetwork range FlagsZones valid DistanceZone Bridge Commands Call Control Commands Device name must be re-entered Calling phone number at data rate, device PPP Call Restriction Commands Call Detail Recording CommandsCompression Information Commands Dhcp CommandsFrame Relay Commands Clears all statistics associated with the fr stat command IP Routing Commands Disables the trace Valid Icmp Echo Reply was received from host ddd.ddd.ddd.ddd Mask used for the destination Age of the route in seconds IPX Routing Commands Ipx ping host ipx address Isdn usage Isdn Usage CommandsLAN Commands LOG CommandsPacket Capture Commands All packets will be captured Following is an example pkt display screen Banyan Vines Packet Detail Screen Bridged Packet Radius Commands Radius ipres Snmp Commands TCP CommandsTelnet Commands Used to close the current Telnet connection to a target host Possible send parameters are defined as follows Terminal Commands Tftp GET Tftp CommandsTftp Session Trace CommandsUser Level Security Commands UDP CommandsCommands WAN CommandsClears the statistics for the default VC System Statistics Connectivity StatisticsCall Restriction Statistics Throughput Monitoring Statistics Call StatisticsAppletalk Protocol Statistics Appletalk StatisticsNumber of AppleTalk Echo requests received Count of AppleTalk Echo replies received Number of NBP LookUp Requests received Appletalk Port Statistics Call Detail Recording Statistics Bridge StatisticsCompression Statistics Compression Related StatisticsDecompression Related Statistics Dhcp Statistics Dhcp Relay Agent statistics and Dhcp Proxy Agent statisticsCommon Dhcp Statistics Dhcp Relay Agent Statistics Dhcp Proxy Client Statistics Frame Relay Statistics Access Related StatisticsNot currently supported PVC Related Statistics LAN Statistics IP Group Statistics IP StatisticsIcmp Group Statistics Number of Icmp Destination Unreachable messages received IPX General Statistics IPX StatisticsNumber of IPX packets received with incorrect checksums IPX RIP Statistics IPX Route Statistics IPX Triggered RIP StatisticsIPX Triggered SAP Statistics IPX Service StatisticsRIP Statistics RIP Global StatisticsRIP Interface Statistics Snmp Statistics SnmpInReadOnlys TCP Statistics Statistics for Server or Remote Initiated Tftp Activity Tftp StatisticsStatistics for ALL Tftp Activity Statistics for Local or Client Initiated Tftp ActivityUDP Statistics WAN Frietf Statistics Layer 1 General Statistics Layer 1 PRI Error StatisticsWAN Statistics Statistics Virtual Circuit VC Related Statistics Local DTE X.121 address Making Changes Using Cfgedit Routine MaintenanceINSTALLING/UPGRADING System Software Executing Configuration ChangesConfiguration Backup and Restore Making Changes Using Manage ModeObtaining System Custom Information System Worksheets AppendicesSystem Worksheets Network Topology System Details ResourcesLines Accesses Device Information Authentication Information Frame Relay InformationIP Routing Bridging and Routing InformationIPX Routing AppleTalk Routing/Port Information Appletalk RoutingFR DBU Main MenuIPX Snmp PPPBPS Physical Resources MenuDES, Feal Hdlc PPP FR DBUOptions Menu WAN RlanDhcp Snmp FR DBU SVC, PVC Security MenuRadius Tacacs ACE IsdnPPP STAC-L25 VRA Manager TCP port Reporting Problems Getting AssistanceContacting Cabletron Systems To Customer Service From Phone FAX Cabletron Systems System Problem ReportNumber of Pages Including this Displays or clears current AppleTalk port statistics Administrative Console Commands TableCommand Use Displays help screenClears current call detail recording statistics Command Use Cdr stats clearVerifies call detail recording servers are configured Clears administration screenDlci Local log file only erases the call detail recording log Generates a triggered RIP/SAP update request toLocal log file only displays the call detail recording log Log cdr eraseDisplays system errors and system messages Changes password for current access levelDisplays the current Tftp statistics Displays current software version and hardware resourceRevision information Specified X.25 access Access or the specified accessManage Mode Commands Table Ipxspoof Allows you to configure system level spoofing data Adds/changes/deletes an IPX address from the IPXAddress pool Manage Mode Commands Table USER’S Guide Cause Codes Table USER’S Guide Cause Codes Table USER’S Guide Workgroup Remote Access Switch USER’S Guide Unknown Dec Value Hex Value CauseCdr 534 cfg IndexBr stat CDRCmp 535 commands DateDel 524 destfilt Device add Device 162Ipcp Ip addrpool 535, 537 IP filters 241Led status 518 line IsdnLan 545 LAN adapter Lan test 355 Lanview LEDs 420 LapbSTAC-LZS NTT INSSrcfilt Restart 523 restoreSentry SpidUdp Term 554 term set 357 terminal modeX25 Wr 52, 521 ws 52