Software Overview, System Software | Cabletron Systems CSX1200

SOFTWARE OVERVIEW

OVERVIEW

The CyberSWITCH software provides:

•system software for the CyberSWITCH, LAN and WAN interfaces, and administration functions

•system files containing configuration and operational information

This chapter provides an overview for each of the above software categories.

SYSTEM SOFTWARE

Included with each CyberSWITCH is a CD containing upgrade software and utility software. (Note that initial system software is factory-installed). The following system software files are available on the CD:

upgrade.osw

All the system files needed for upgrading the CyberSWITCH are combined in this file.

defltcfg.osw

All of the system files needed to return your system configuration to the factory default are combined in this file.

SYSTEM FILES

The CyberSWITCH uses a flash file system (instead of a hard disk) and a two-stage boot device to initialize the platform and download the system software. The flash file system basically performs the same as a hard disk, but it has no drive letter. Just as on a hard disk, the flash file has directories with files.

CONFIGURATION FILES

The configuration files store the configuration data. These files are located in the system’s \config directory. You can maintain these files by using the CFGEDIT configuration utility, which is delivered with the system. You can also make changes to these files through Manage Mode.

The configuration files associated with the system are:

network.nei

This configuration file contains information about the switched network.

devdb.nei

This file contains the On-node Device Database configuration information about each remote device.

Image 51

Cabletron Systems CSX1200, CSX1000 manual Software Overview, System Software, System Files, Configuration Files

Contents

USER’S Guide Virus Disclaimer Trademarks DOC Notice Contents Ordering Isdn Service US Only Cfgedit Configuration Tools Security Overview Configuring System Options and Information Configuring Off-node Server Information Configuring Advanced Bridging Configuring Advanced IP Routing Configuring IPX Configuring Snmp Configuring Other Advanced Options System Verification Problem Diagnosis LED Indicators System Messages System Statistics Routine Maintenance Cfgedit Map Using this Guide Cfgedit MAP Documentation SET Guide Conventions Cfgedit ScreensUser’s Guide System Overview CyberSWITCH Cyberswitch Network Cyberswitch Isdn Unique System Features Cyberswitch Interoperability Overview RadiusInteroperability Protocols Interoperability Devices Network Interface Overview Security Overview System Components Isdn Remote Isdn Devices Switches Supported Hardware Overview Safety Considerations CSX1000 and NE Link 1000 a Network Express Product System Platforms CSX1001, shown below, is equivalent to the NE Link 1000 B2 Workgroup Remote Access Switch System Characteristics EMI CSX1200 CSX1204 BRI Version LAN Access Cabling InformationAUI Pin Signal Function Transmit + Receive + No Connect Basic Rate Interface WAN Access Transmit Data Pin Signal Function Carrier DetectRing Indicator Receive Data System Modules CSX1200-E11-MOD System Modules CSX1200-U4-MOD System Software Configuration FilesSoftware Overview Overview Operational Files User Level Security Files Accessing the CyberSWITCH System Installation Workgroup Remote Access Switch Ordering BRI Isdn Lines Using Provisioning Settings Ordering Isdn Service US onlyOrdering NI-1 Lines Using EZ-ISDN Codes Ordering NI-1 Lines Using NI-1 Isdn Ordering Codes NI-1 AT&T Custom Point-to-Point Provisioning Settings for AT&T 5ESS Switches CSD limit CSD NB limit AT&T 5ESS NI-1 ServiceUnrestricted CSV limit CSV NB limit CSV limit AnyCSD limit Provision Settings for Northern Telecom DMS-100 Switches Number of call Appearances Version Functional YesBasic Information for Ordering PRI Isdn Lines Sprint Type of SwitchDisabled Option Local Bell Operating Company Verify administration console requirements Hardware InstallationPRE-INSTALLATION Requirements Choose a suitable setup location Installing the CSX1200-E11-MOD Installing the CSX1200-U4-MOD Cabling NULL-MODEM Connection to a PC Accessing the CyberswitchMaking Connections Direct Connection Changing the Baud Rate Remote Connection Using a Modem Remote Connection Using Telnet Powering on Establishing AN Administration Session Admin Accessing the Release Notes Upgrading System Software Upgrading SoftwareCD File Structure Product Country or Directories Switchtype Upgrading Software Local Software Upgrade This message is displayed Remote Software Upgrade Flash recover Console Messages during SSB Upgrade Change Defaults to Secure System Return Configuration to Factory Defaults Configuring Basic Bridging Basic Configuration Executing Cfgedit Configuration Tools Dynamic Management Saving Cfgedit ChangesExecuting Dynamic Management Saving Dynamic Management Changes Utility Dynamic Management Commands Using the Network Worksheets Default Configuration Using the Configuration Chapters Configuring Resources and Lines Configuring Resources Using CfgeditResources United States Resource Background Information Resource Configuration Elements PPP Lines Configuring Lines Using Cfgedit Characteristic PRI/T1 lines E1 line Multiframe CRCCommonChannel Auto TEI Line Configuration Elements Switch Type Number of Data Number of SPIDs Directory NumbersDMS100 custom NI-1 Service Profile ID Spid Robbed Bit Signaling is not supported for the CyberSWITCH Line Background Information Commport Information Subaddresses Background Information Configuring a Subaddress Using CfgeditSubaddress Configuration Elements Subaddresses MAC Layer Bridging Configuration Elements Configuring Basic BridgingENABLING/DISABLING Bridging Using Cfgedit Select Enable/Disable Bridging MAC Layer Bridging Background Information Configuring Basic IP Routing Enabling IP Using CfgeditInternet Protocol IP Option IP Background Information IP Operating ModeIP Option Configuration Elements Configuring the IP Operating Mode Using Cfgedit IP Operating Mode Background Information IP Operating Mode Configuration Elements IP Network Interfaces Configuring Interfaces Using Cfgedit USER’S Guide Network Interface Configuration Elements MTU Transmit Broadcast IP Address Default switch for numbered WAN interfaces IP RIP Receive Control IP Network Interface Background Information Hdlc Bridge IP Network Interface Type Associated Remote DeviceIP Host RFC1294 WAN Direct Host IP Host RFC1294 USER’S Guide Example 1 LAN, WAN and WAN Direct Host Interfaces Example 2 LAN, WAN UnNumbered, WAN Remote LAN Interfaces IP RIP and the IP Network Interfaces Isdn Isdn IP RIP Over Dedicated Connections SITE3 Redundant Configurations for Backup Network FlatteningProxy ARP Example IP Host Communications in Flattened Networks Secondary IP Addressing Static Routes Configuring Static Routes IP address for the destination network or host Static Route Configuration Elements Workgroup Remote Access Switch Static Route Background Information Isdn Default Routes Configuring Default RoutesDefault Route Configuration Elements Routing Information Protocol RIP Option ENABLING/DISABLING IP RIP Using Cfgedit LAN IP RIP Configuration ElementsIP RIP Status IP RIP Background Information Security Configuring Security Level Security Level Security Overview Device Level Databases System Options and Information Network Login Information User Level DatabasesOFF-NODE Server Information Configuring Security Level On-Node Yes Database Device Level User Level Administration Security No Security Configuring no Security Using Cfgedit Configuring Device Level Security Using Cfgedit Device Level SecurityDevice Level Security Background Information Configuring User Level Security Using Cfgedit User Level SecurityUser Level Security Background Information User Level Security Isdn Making a Telnet Connection Responding to Login Prompts ACE Configuring Device and User Level Security Using CfgeditDevice and User Level Security Tacacs Device and User Level Background Information Configuring System Options and Information Configuring System Options Using CfgeditSystem Options System Options System Options Configuration Elements PAP Chap Bridge MAC Calling Line Id Authentication Address PAP Chap System Options Background Information Optional Calling Line Id Configuring System Information Using CfgeditSystem Information Configuration Elements System Information Administrative Session Configuring Administrative Sessions Using CfgeditSystem Information Background Information Administrative Session Configuration Elements Administrative Session Background Information Emergency Telnet Server Port Number Background Information Configuring Device Level Databases Configuring AN ON-NODE Device DatabaseON-NODE Device Database ON-NODE Device Entries Configuring ON-NODE Device Entries On-node Device Entries No pvc configured for Device DAN SVC 0.0 Routing Device ON-NODE Device Database Configuration Elements DIAL-OUT Phone Numbers Chap Secret Outbound Authentication RIP/SAP Appletalk Information Configuration Elements Bridge Information Configuration Elements Bridging with Hdlc Bridge Devices ON-NODE Device Database Background Information Security Mode On-node Device Table Configuration Data IP Routing with Hdlc Bridge DevicesLine Id IP Routing with PPP IP Devices Using Ipcp IP Routing with IP Host Devices RFC1294PAP or Chap Bridging with PPP Bridge Devices Using BCP PAP Password orIP Routing with PPP Bridge Devices Using BCP OFF-NODE Device Database Location Configuring OFF-NODE Device Database Location Using Cfgedit OFF-NODE Device Database Location Background Information OFF-NODE Device Database Location Configuration Elements Configuring User Level Databases User Level Authentication Database LocationConfiguring Authentication Database Location Using Cfgedit User Level Authentication Database Location Type communications server Configuring OFF-NODE Server InformationMultiple Administration Login Names Name John Doe Name mynode1 Address Remote Office1 Configuring VRA Manager Authentication Server VRA Manager Authentication Server Configuring a Radius Authentication Server Radius Authentication ServerVRA Manager Authentication Server Configuration Elements VRA Manager Authentication Server Background Information Displays the current Radius server configuration data Radius Authentication Server Background Information Radius Authentication Server Configuration Elements Configuring a Tacacs Authentication Server Tacacs Authentication Server Tacacs Authentication Server Background Information Tacacs Authentication Server Configuration Elements Configuring AN ACE Authentication Server ACE Authentication Server ACE Authentication Server Configuration Elements ACE Authentication Server Background Information Configuring Network Login Information Network Login General ConfigurationConfiguring General Network Login Information Using Cfgedit Network Login General Configuration Background Information Network Login Banners Configuring Network Login Banners Using CfgeditNetwork Login Banners Background Information Configuring Radius Server Login Information Using Cfgedit Login Configuration Specific to Radius Server Configuring Tacacs Server Login Information Using Cfgedit Login Configuration Specific to Tacacs Server Login Configuration Specific to Tacacs Server Login Elements Specific to Tacacs Configuring Alternate Accesses Advanced Configuration Dedicated Access Configuration Elements Configuring Alternate AccessesDedicated Accesses Configuring a Dedicated Access Using Cfgedit Dedicated Access Background Information Configuring AN X.25 Access Accesses Accesses USER’S Guide Configuration Elements Lapb Configuration Elements Timers Maximum Window Size Nonstandard Default Transmit Window Size PVC Configuration Elements Access Background Information B1 B2 Configuring a Frame Relay Access Frame Relay Accesses Configuring a PVC Frame Relay General Configuration Elements Dlci Value Frame Relay PVC Configuration ElementsLMI LMI Format PVC Name Frame Relay Access Background Information Local Management Interface Overview Allowed Not Allowed Bridge Dial OUT Configuring Advanced Bridging Under ISDN, select Dial Out Phone Number Spanning Tree Protocol Bridge Mode of Operation Bridge Mode of Operation Background Information Bridge Filters Configuring Bridge Filters Using Cfgedit Protocol Filter Commands Protocol Definition CommandsSource MAC Filter Commands Destination MAC Filter Commands Packet Data Filter Commands Bridge Filter Configuration ElementsLsap in HEX Bridge Filters Background Information Filter Type Maximum Number of EachFilter Destination MAC Protocol Definitions Source Discard Connect Destination Protocol Packet Unrestricted Mode Bridge Filters USER’S Guide Sites connected over the WAN according to Filter Action Distribution Result ListPacket matching this filter will not be forwarded On any LAN port. The packet will be sent to remote Restricted Mode Forwarding Action Restricted Mode Bridge Filters Workgroup Remote Access Switch Any remote sites connected over the WAN Filter Distribution Result Action ListPacket matching this filter will only be forward Ed on the LAN ports. The packet will not be sent to Preliminaries Configuring a Destination MAC Address Filter Discard Connect Known Connect List Configuring the Known Connect List Known Connect List Background Information Known Connect List Configuration Elements Static ARP Table Entries Configuring Advanced IP Routing Select Static ARP Table Entries from the IP menu Configuring Static ARP Table Entries Using CfgeditStatic ARP Table Entries Configuration Elements Static ARP Table Entries Static Route Lookup VIA Radius Isolated Mode IP Address Pool Static Route VIA Radius Configuration ElementsConfiguring AN IP Address Pool Using Cfgedit IP Address Pool Configuration Elements Initiating the IP Filter Configuration Using Cfgedit IP FiltersIP Address Pool Background Information Configuring Packet Types Using Cfgedit TCP UDP Icpm Mask Specify a control value any, established, or not established Select Icmp Type Select Add a Forwarding Filter Configuring Forwarding Filters Configuring Connection Filters Configuring Exception Filter Select Device Level Databases Select On-node Device Entries Applying FiltersSelect IP Interfaces Select Apply Global Forwarding Filter IP Filters Configuration Elements IP Filters Background Information TCP and UDP PortsNEQ Range Forwarding Filters Packet Types Exception Filters Connection Filters Application to Network Interfaces Limitations Common Portion FTP WWW Sfvra Example of AN IP Filter Configuration Forward Dhcp Relay Agent Configuring a Dhcp Relay Agent Using Cfgedit Dhcp Background Information Dhcp Configuration Elements Router to Bridge Environment Bridge to Bridge Environment IP Router to IP Router with Relay Agents on both USER’S Guide Remote Bridge to IP Router w/Relay Agent = WAN Rlan Configuring the Dhcp Proxy Client Dhcp Proxy ClientSelect Dhcp Proxy Client Dhcp Proxy Client ENABLE/DISABLE Flag Sample Configuration IP Router with Dhcp Proxy Client Configuration for IP Router Chloe Configuring IPX Configuring IPX Information ENABLING/DISABLING IPX Using Cfgedit IPX Option Configuration ElementIPX Routing Option IPX Option Background Information Configuring the IPX Internal Network Number Using CfgeditIPX Internal Network Number Configuration Element IPX Internal Network Number LAN WAN Configuring IPX Network Interfaces Using CfgeditIPX Network Interfaces IPX Network Number Background Information Displays the current IPX network interface data IPX Network Interface Configuration Elements SAP IPX Network Interface Configuration Elements IPX Network Interface Background Information Configuring IPX Routing Protocols Using Cfgedit IPX Routing Protocol Configuration ElementsIPX Routing Protocols SAP IPX Routing Protocol Background Information Special Considerations Remote LAN Interface IPX Static Routes Configuring IPX Static Routes Using Cfgedit IPX Static Routes Background Information IPX Static Routes Configuration Elements Configuring IPX Netware Static Services Using Cfgedit IPX Netware Static Services IPX Netware Static Services Configuration Elements IPX Netware Static Services Background Information Configuring IPX Spoofing Using CfgeditIPX Spoofing IPX Spoofing Background Information IPX Spoofing Configuration Elements Watchdog Protocol IPX Type 20 Packet Handling Configuring IPX Type 20 Packet Handling Using Cfgedit IPX Isolated Mode Configuration Elements IPX Isolated ModeIPX Type 20 Packet Handling Configuration Elements Configuring IPX Isolated Mode Using Cfgedit Displaying WAN Peer List IPX Isolated Mode Background Information Configuring Triggered RIP/SAP Global Timers Using Cfgedit Configuring IPX Devices IPX-SPECIFIC Information for DevicesTriggered RIP/SAP Background Information IPX-Specific Information for Devices SPX Watchdog Spoofing Menu Enable Bridging and disable Make calls for bridge data IPX Configuration Elements for Devices IPX Background Information for Devices Configuring Snmp Configuring Snmp Configuring Snmp Snmp Configuration Elements Snmp Background Information WAN Workgroup Remote Access Switch USER’S Guide Configuring Appletalk Routing Enabling Appletalk Routing Using CfgeditAppletalk Routing Option Appletalk Routing Background Information Appletalk Routing Option Configuration ElementConfiguring Appletalk Ports Using Cfgedit Appletalk Ports Appletalk Ports Configuration Elements Appletalk Ports Background Information Overview Considerations ConfigurationConfiguring Appletalk Static Routes Using Cfgedit Appletalk Static Routes Appletalk Capacities Appletalk Routing Static Routes Configuration ElementsConfiguring Appletalk Capacities Using Cfgedit Appletalk Capacities Configuration Elements Appletalk Capacities Background Information Appletalk Isolated ModeConfiguring the Appletalk Isolated Mode Using Cfgedit Appletalk Isolated Mode Configuration Elements Configuring Call Control Configuring the Throughput Monitor Using CfgeditThroughput Monitor Throughput Monitor Configuration Elements Throughput Monitor Background Information Condition Trigger Number Window Size Utilization90% Overload Condition Monitoring Idle Condition Monitoring Call Interval Background Information Configuring the Call Interval Parameters Using CfgeditCall Interval Configuration Elements Call Interval Parameters Monthly Call Charge Background Information Configuring Monthly Call Charge Using CfgeditMonthly Call Charge Configuration Elements Monthly Call Charge Configuring Call Restrictions Using Cfgedit Call Restriction Configuration ElementsCall Restrictions Call Restrictions Call Restrictions Background Information Bandwidth Reservation Configuring Bandwidth Reservation = CentralSite Select Bandwidth Reservation Bandwidth Reservation Configuration Elements Configuring Semipermanent Connections Using Cfgedit Semipermanent ConnectionsBandwidth Reservation Background Information Semiperm Semipermanent Connections Configuration Elements Call Device CommandsSemipermanent Connections Background Information Throughput Monitor Call Restrictions VRA Manager AS a Call Control Manager Configuring VRA Manager for Call Control Using Cfgedit Background Information LIMITATIONS/CONSIDERATIONS Configuring Other Advanced Options PPP ConfigurationConfiguring PPP PPP Configuration Elements PPP Background Information PPP Reference Documents Default Line Protocol Background Information Default Line ProtocolConfiguring Default Line Protocol Using Cfgedit Default Line Protocol Configuration Elements UDP Port Configuring LOG Options Using CfgeditLOG Options Configuration Elements LOG Options LOG Options Background Information CDR LOG Report Overview Call Detail Recording Events Event Report Contents Connect Event Report Contents Disconnect Event Report Contents Reject Event Report ContentsSystem Up Event Report Contents Compression Options Verify Event Report ContentsConfiguring Compression Options Using Cfgedit Compression Options Configuration Elements Compression Options Background Information Compression and CCP Tftp Configuring Tftp Tftp Background Information Tftp Configuration Elements File Attributes Background Information Configuring File AttributesFile Attributes Configuration Elements File Attributes STATLOG.1 Users Report Files StatFiles CfgFiles Other FilesFile category File types included in the category RPRTLOG.1 System Verification Troubleshooting Verifying Hardware Resources are Operational System Verification Verifying LAN Connection is Operational Verifying WAN Lines are Available for USE Verifying IP Router is Initialized Verifying Bridge is Initialized Verifying a Frame Relay Connection Verifying a Dedicated Connection Verifying AN X.25 Connection Verifying Remote Device ConnectivityVerifying MULTI-LEVEL Security Ping 100.0.0.2 return Verifying IP Host Mode is Operational Verifying IP Host Mode is OperationalVerifying IP Host is Initialized Verifying IP Routing Over a LAN Interface Verifying IP Routing Over Interfaces Verifying IP Routing Over a WAN Interface 100.0.0.1 100.0.0.0 Host B 192.100.1.3 Host a 100.0.0.2 Verifying IP Routing Over a WAN Direct Host Interface Verifying IP Routing Over a WAN Remote LAN Interface Verifying IP Routing Over a WAN Unnumbered Interface Verifying IP RIP is Initialized Verifying IP FiltersVerifying IP RIP Ip filter trace discard return Verifying IP RIP Output Processing on a LAN Interface Verifying IP RIP Output Processing on a WAN Interface Verifying IP RIP Input Processing on a LAN Interface CSX1200 Router Dedicated Connection 100.1.1.1 192.1.1.1 Verifying IPX Routing is Operational Verifying IPX Router is Initialized Verifying IPX Routing Over a LAN Connection Verifying AN IPX Remote LAN ConnectionXxxx Verifying Appletalk Routing is Initialized Verifying the Appletalk Routing FeatureVerifying IPX Routing Over a WAN Connection Verifying Triggered RIP/SAP Verifying Appletalk Routing is Operational Verifying Appletalk Routing Operation Over a WAN Connection Verifying Snmp is Operational Verifying Call Detail Recording Verifying the Dial OUT Feature Verifying Compression is Operational Verifying Reserved Bandwidth is OperationalVerifying PPP Link Failure Detection is Operational Verifying Dhcp Relay Agent Initialization Verifying Dhcp Relay Agent Verifying the Relay Agent is Operational Verifying the Relay Agent is Enabled Verifying Dhcp Proxy Client Initialization Verifying Dhcp Proxy Client Verifying the Proxy Client is Enabled Verifying the Proxy Client is OperationalUDP Ports Verifying Proxy ARP is Operational Verifying a Semipermanent Connection Verifying Proxy ARP is Operational LAN Adapter Problem DiagnosisGeneral Procedures Problem Bridge Initialization IP Routing InitializationWAN Line Availability Out Svc 1 slot #, port # Frame Relay Connections Dedicated Connections Connections Set-up Remote Device Connectivity Disabled MULTI-LEVEL SecurityLAN Attachment IP Host Mode IP Host Mode Operation Over the LAN ConnectionIP Host Initialization IP Host Mode Operation Over the WAN Connection IP Routing Over Interface ConnectionsIP Routing Over the LAN Interface Connection IP Routing Over a WAN Interface Connection IP Routing Over a WAN Direct Host Interface Connection IP Routing Over a WAN Rlan Interface Connection IP Routing Over a WAN Unnumbered Interface Connection IP RIP Initialization If you are still experiencing problems IP RIP Input Processing on a LAN Interface IP RIP Output Processing on a LAN Interface IP RIP Input Processing on a WAN Interface IP RIP Output Processing on a WAN Interface IPX Routing IPX Routing InitializationIPX Routing Over the LAN Connection IPX Routing Over the Remote LAN Connection IPX Routing Over the WAN Connection IPX Routing and Service Tables Appletalk Routing Triggered RIP/SAP Start UPTriggered RIP/SAP Operation Appletalk Routing Operational Over the LAN Connection Appletalk Routing Initialization USER’S Guide Appletalk Routing Operational Over the WAN Connection Snmp CyberSWITCH does not generate Snmp Trap PDUs Dial OUT Set Up Call Detail Recording Compression Successful NegotiationPeer Protocol-Rejects CCP CyberSWITCH does not have Compression Enabled Relay Agent InitializationEnabling the Relay Agent Proxy Client Initialization Relay Agent Operation Proxy Client Operation Enabling the Proxy Client Proxy ARP Operation Proxy ARP Operation Local Area Network LED Indicators LED Indicators PRI LED Indicators Lanview Leds CSX1200-E11-MOD OFF Receive LEDs Service Indicator Remains LIT Service Indicator OUT SVC LAN Xmit Error Service Indicator Blinks Alarm Leds PRI only Alarm LEDs PRI Only Informational Messages System Messages Status Messages Boot MessagesInitialization Messages Normal Operation Messages Error Messages System Message SummarySpanning Tree Messages Adapter #’x’ failed to respond from bootstrap Port LAN Adapter, operating in remote mode onlyPort LAN Adapter, operating in local and remote mode Call has exceeded the configured maximum duration Auth ACE Could not write service file Attempting to load FileName for UpgradeAttempt to initialize unconfigured DM card in slot slot # Auth ACE Could not create service file Auth ACE Node verification received Client initialized Auth ACE Encryption configured for DES not supportedAuth ACE Error receiving server log message acknowledgment Auth ACE Login rejected user user name Auth Radius PAP rejected device device name Auth Radius Login rejected device device nameAuth Radius IP Host rejected IP Host id IP host Id Auth Radius IP Resolve rejected IP Address IP address Auth Warning code 0007 Authentication mode mismatch Auth Tacacs Login rejected user user nameAuth Warning code 0001 Timeout Auth Warning code 0004 No authentication node available Bad auth result in smgrauthaanotify for device device name Booting System SoftwareBootstrap came alive on DM card in slot slot # Bootstrap came alive on WAN card in slot slot # Calling Line ID Failure, Duplicate ID calling line Id Call Restrictions have been disabled by user commandCall Restrictions have been enabled by user command Calculating CRC’s Call Restrictions will allow calls to be made Call Restriction statistics reset for new dayCall Restriction statistics reset for new month Call Restrictions will allow calls to be made this hour Workgroup Remote Access Switch CCP Option Negotiation Failure, Non-Convergence detected Cause cause code received for Dlci dlci indexCause Code Event CCP Internal Decompression Failure Channel in use in Hostcallrequest Chap Authentication Failure remote device not responding CNTR-TMRTimed out waiting for TMR number interrupt Configured adapter # ’x’ type does not existCouldn’t find speech service slot #, port # Current monthly charges reset for new month DHCP-P Failed to open UDP port x, erc = y Dedicated connection down slot #, port #DHCP-P Failed to close UDP port x, erc = y DHCP-P Failed to open UDP port for first Dhcp client DHCP-P Proxy Client initialization failed DHCP-P Proxy Client disabledDHCP-P Proxy Client enabled DHCP-R Relay Agent disabled DHCP-R UDP port 67 opened DHCP-R Relay Agent enabledDHCP-R Relay Agent initialization failed DHCP-R UDP port 67 closed DM upgrade started. Board=board #, Modem=modem # DM card in slot slot # signals it is operationalDM card type configured in slot slot # does not exist DM card in slot slot # will not come out of reset DSL test failed to establish Layer 1, port=port # DM upgrade success. Board=board #, Modem=modem #Downloading Bootstrap to DM card in slot slot # Edrv transmit error error code Error during channel initialization Access access index Error closing file ’s’Error downloading bootstrap program to adapter #’x’ Error downloading operational software to adapter ’x’ Error programming adapter #’x’ hardware Error mapping WAN adapter #’x’ into Host memory mapError parsing old WAN Direct Host interface bad format Error opening file \system\ethernt2.bin Facility not subscribed Slot=slot # Port=port # Error reading sdconf.rec fileError requesting slot activation Error sending message to Call Control Failure to allocate enough memory for Xilinx load file Failed to obtain Terminal info in smgrprocterminalauthsessFailure during read of file ’s’ Failure during Static RAM test on adapter # ’x’ USER’S Guide Frame Relay event queue full File Access ErrFormatting Flash Memory Frietf detected PPP protocol from NAME, shutting down PVC Initial TDM Clock Master slot#, line# Installing File Set into Flash MemoryInterrupt fault on WAN Adapter in Slot slot # FrUtl No registered device for Dlci dlci index IP x.x.x.x not added to the pool Unknown error y Invalid Cllm received on Access access indexInvalid Password password given IP Error from ESP datagram discarded IP Cannot get system memory for IP Default Route not added, invalid next hop IP address #IP Invalid configuration for Network Interface dd Ipap ResMem returned invalid device maximum value IP Network initialized successfully on ddd.ddd.ddd.ddd IP Invalid Peer IP Address IP address, WAN IP Stream ClosedIP IP host is initialized successfully IP IP router is initialized successfully IP Host Call Dropped XID was not received from remote Ipcp IP Address Pool Out of IP addressesIpcp Option Negotiation Failure, Non-Convergence detected Ipcp Remote device does not negotiate IP address IP RIP Initialization failed, unable to allocate buffers IP Host Security Rejection Invalid Security ID Id stringIP RIP All network interfaces used IP RIP Buffers allocated IPX Network initialized successfully on IP RIP Unable to open RIP/UDP portIP RIP Unable to register WAN Connection notification IPX Invalid Ipxwc passed IPX RIP Shutdown complete IPX SAP Space available in service tableIPX SAP Unable to add service, service table full Ipxwan IPX Internal Network Number must be configured LAN Adapter HW upgrade may be required LAN Adapter Command TimeoutLAN Adapter configuration conflict LAN Adapter Fatal Error Reported LAN Init Error LAN Adapter ResetLAN Adapter Response Timeout LAN Adapter System resource error LAN Port port # detected shorted LAN media LAN Xmit ErrorLMI alarm on Access access index LMI alarm reset Access access index Manual restart initiated on DM board in slot slot # Manage Mode updates have been successfully committedMemory Access Timeout Manual intervention required please replace LAN card Negotiation Failure with Semipermanent device Mismatch of configured and installed DM card in slot slot #Modem modem # of DM card in slot slot # is unusable Modem revision on modem modem # of slot slot # failed No Active List entry available in INM Network sent Cause Spid not supported slot #, port #Network sent Status with state = 0, tear down call No Active Calls Active Sites Outgoing calls barred Slot=slot # Port=port # Out of LAN Adapter transmit command descriptorsNot enough memory for Security module Offnode server lookup of Dial Out User failed Out Svc # slot # , port # Auto For over 5 minutes Report problem to Phone companyPAP Identification timeout on remote device PAP Invalid password for name given by remote device Post number, Hdlc #number Internal Loopback Test Failed PAP Remote device rejected System Information error messagePAP Unknown name name given by remote device Post number, Hdlc #number External Loopback Test Failed PVC not allocated for dlci index RBS LIFAddTimer failureRBSoutSMchannel # Timeout waiting for Wink PVC for Dlci dlci index not Active Reserved signal Reattempting to Install File Set into Flash MemoryRebooting Replace Lithium Battery Contact your Representative Security Rejection Caller did not negotiate security Security Rejection Invalid Password password givenRetrying download of DM card in slot slot# in x seconds Rx Channel Inactivity Detected Security Rejection No Protocol List supplied Security Rejection No Password given by callerSecurity Rejection Timeout on Startup Complete Semipermanent. Device x disconnected by admin Snmp Authentication failure, unknown community name Semipermanent. Device x reconnected by adminSignal for unknown CallCmd task task Id Slot #, port # Cfg Error SSB i960 Post number not equal to i386’s SSB Post 27 i960timer82c54FAILURESSB Can’t read RTC prior to i960 POSTs SSB Couldn’t read RTC during i960 POSTs SSB Post 31 i960permodmem2 Failure SSB Post 28 i960lan82596sx FailureSSB Post 29 i960lan82503 Failure SSB Post 30 i960permodmem1 Failure STP a Blan Topology Change has been detected Successfully Loaded Release X.Y Issue ZSwitch could not recognize phone number nnnnnnn System Clock Fault on Wan Adapter in Slot slot # Tftp Local error #5 UDP open failed Tftp Local error #2 Feature not initializedTftp Local error #3 Server not initialized Tftp Local error #4 UDP rejected packet filename Tftp Local error #18 Unable to open file filename Tftp Local error #13 Received unexpected opcode filenameTftp Local error #14 Bad file name Tftp Local error #15 Bad mode string Tftp Remote error # 3 Text from Remote Host Tftp Remote error # 0 Text from Remote HostTftp Remote error # 1 Text from Remote Host Tftp Remote error # 2 Text from Remote Host Timeout on Startup Complete Compression subsystem is not enabledTimeout detected on connection establishment Timeout detected on receiving caller’s number Type mismatch of configured & installed adapter # ’x’ Unable to Decrypt DatagramUnable to get Digital Modem resource to place call Unable to Identify a remote device Unable to open \config\devdb.nei fileUnable to open Modem Upgrade file Unable to restore original ISRs for Interrupt interrupt # WAN card in slot slot # signals it is operational Unexpected error during transmission of LMI frameUnmatched Login Task Updating CyberSWITCH from FileName X25 facilities error, bad facility length Watchdog timeout detected on DM board in slot slot #Watchdog timeout detected on WAN board ’x’ X25 facilities error, facilities not allowed in PVC X25 facilities error, throughput negotiation not allowed X25 facilities error, reverse charging not acceptedX25 facilities error, fast select not available X25 facilities error, fast select not accepted Zone allocation failed, maximum capacity already configured X25 facilities warning, NUI not availableZone allocation failed, increase zone table capacity Trace Messages Location Causes Call Trace Messages Call Trace Message Summary Configure ack slot # Inband treatment has been applied-BRD CFG ACK Slot=slot # Init data link slot #, port #, ces Origination call address is non-ISDN Out configure port #Interworking unspecified cause Off-hook warning tone on Received unknown progress value Received unknown signal valueOut init data link slot #, port # , ces Recall dial tone on IP Filters Trace Messages PPP Packet Trace Messages Configure Reject Configure RequestConfigure ACK Configure NAK Trace Message Summary Trace MessagesEcho Reply Discard Request X25 DCE RR LCN logical channel number, number of bytes bytes X25 Data LCN logical channel number, number of bytes bytes System is sending a call request to the network Lapb Trace Message Summary Lapb Trace Messages Out Lapb DM Lapb SabmeLapb UA Out Lapb Disc Remote Management System Maintenance Remote Management SITE.2 Installation and Configuration Usage Instructions Telnet Earlier Releases Usage Instructions Tftp Client PC Users Report Files Statistics Files Config files Other Files Remote Installation with USER2 USER’S Guide Accessing Administration Services System Commands Boot Device Commands Setting the IP Address Viewing Operational Information Accessing Dynamic Management List relnote.txt Viewing Operational Information Status Second column is the potential number of connections 100 Viewing Throughput Information Saving Operational Information Throughput Monitor Contents Clearing Operational Information CONFIGURATION-RELATED Commands Restarting the Cyberswitch Setting the Date and TimeFile Utility Commands Login-Id Terminating Administration Sessions Appletalk Routing Commands State Type LAN port Default zoneNetwork range Flags Zones valid Distance Zone Bridge Commands Call Control Commands Device name must be re-entered Calling phone number at data rate, device PPP Call Restriction Commands Call Detail Recording Commands Compression Information Commands Dhcp CommandsFrame Relay Commands Clears all statistics associated with the fr stat command IP Routing Commands Disables the trace Valid Icmp Echo Reply was received from host ddd.ddd.ddd.ddd Mask used for the destination Age of the route in seconds IPX Routing Commands Ipx ping host ipx address Isdn usage Isdn Usage Commands LAN Commands LOG CommandsPacket Capture Commands All packets will be captured Following is an example pkt display screen Banyan Vines Packet Detail Screen Bridged Packet Radius Commands Radius ipres Snmp Commands TCP CommandsTelnet Commands Used to close the current Telnet connection to a target host Possible send parameters are defined as follows Terminal Commands Tftp GET Tftp Commands Tftp Session Trace Commands User Level Security Commands UDP Commands Commands WAN Commands Clears the statistics for the default VC System Statistics Connectivity StatisticsCall Restriction Statistics Throughput Monitoring Statistics Call Statistics Appletalk Protocol Statistics Appletalk Statistics Number of AppleTalk Echo requests received Count of AppleTalk Echo replies received Number of NBP LookUp Requests received Appletalk Port Statistics Call Detail Recording Statistics Bridge Statistics Compression Statistics Compression Related StatisticsDecompression Related Statistics Dhcp Statistics Dhcp Relay Agent statistics and Dhcp Proxy Agent statisticsCommon Dhcp Statistics Dhcp Relay Agent Statistics Dhcp Proxy Client Statistics Frame Relay Statistics Access Related Statistics Not currently supported PVC Related Statistics LAN Statistics IP Group Statistics IP Statistics Icmp Group Statistics Number of Icmp Destination Unreachable messages received IPX General Statistics IPX Statistics Number of IPX packets received with incorrect checksums IPX RIP Statistics IPX Route Statistics IPX Triggered RIP Statistics IPX Triggered SAP Statistics IPX Service Statistics RIP Statistics RIP Global StatisticsRIP Interface Statistics Snmp Statistics SnmpInReadOnlys TCP Statistics Statistics for Server or Remote Initiated Tftp Activity Tftp Statistics Statistics for ALL Tftp Activity Statistics for Local or Client Initiated Tftp Activity UDP Statistics WAN Frietf Statistics Layer 1 General Statistics Layer 1 PRI Error Statistics WAN Statistics Statistics Virtual Circuit VC Related Statistics Local DTE X.121 address Making Changes Using Cfgedit Routine MaintenanceINSTALLING/UPGRADING System Software Executing Configuration Changes Configuration Backup and Restore Making Changes Using Manage ModeObtaining System Custom Information System Worksheets Appendices System Worksheets Network Topology System Details ResourcesLines Accesses Device Information Authentication Information Frame Relay Information IP Routing Bridging and Routing Information IPX Routing AppleTalk Routing/Port Information Appletalk Routing FR DBU Main MenuIPX Snmp PPP BPS Physical Resources MenuDES, Feal Hdlc PPP FR DBU Options Menu WAN RlanDhcp Snmp FR DBU SVC, PVC Security MenuRadius Tacacs ACE Isdn PPP STAC-L25 VRA Manager TCP port Reporting Problems Getting AssistanceContacting Cabletron Systems To Customer Service From Phone FAX Cabletron Systems System Problem ReportNumber of Pages Including this Displays or clears current AppleTalk port statistics Administrative Console Commands TableCommand Use Displays help screen Clears current call detail recording statistics Command Use Cdr stats clearVerifies call detail recording servers are configured Clears administration screen Dlci Local log file only erases the call detail recording log Generates a triggered RIP/SAP update request toLocal log file only displays the call detail recording log Log cdr erase Displays system errors and system messages Changes password for current access level Displays the current Tftp statistics Displays current software version and hardware resourceRevision information Specified X.25 access Access or the specified access Manage Mode Commands Table Ipxspoof Allows you to configure system level spoofing data Adds/changes/deletes an IPX address from the IPXAddress pool Manage Mode Commands Table USER’S Guide Cause Codes Table USER’S Guide Cause Codes Table USER’S Guide Workgroup Remote Access Switch USER’S Guide Unknown Dec Value Hex Value Cause Cdr 534 cfg IndexBr stat CDR Cmp 535 commands DateDel 524 destfilt Device add Device 162 Ipcp Ip addrpool 535, 537 IP filters 241 Led status 518 line IsdnLan 545 LAN adapter Lan test 355 Lanview LEDs 420 Lapb STAC-LZS NTT INS Srcfilt Restart 523 restoreSentry Spid Udp Term 554 term set 357 terminal mode X25 Wr 52, 521 ws 52