Layer 1 PRI Error Statistics | Cabletron Systems CSX1000, CSX1200

USER’S GUIDE

AIS (Blue)

The number of times layer 1 has detected a qualified unframed all ones signal.

RAI (Yellow)

The number of times layer 1 has detected a qualified RAI (remote alarm indication) signal.

LAYER 1 PRI ERROR STATISTICS

Note: Layer 1 PRI error statistics apply to the line connected to the indicated slot.

Bipolar Violations

The number or times there has been either a mismatch between encoding types (B8ZS not selected) or line noise.

ESF CRC Errors

The number of Cyclic Redundancy Check (CRC) errors in the PRI framing format (ESF framing only).

Framing Bit Errors

The number of errors in the framing bits of the PRI layer 1 framing format.

Recv Negative Slips

The Number of PRI frames lost due to timing problems in the negative direction.

Global Parity Errors

The number of parity errors seen across all transmit and receive channels.

Recv Positive Slips

The number of PRI frames lost due to timing problems in the positive direction.

Recv Parity Errors

The number of receive parity errors.

Xmit Slips

The number of times an error has occurred in the host clock system. If the wander of the transmit route clock is too great, data transmission errors will occur.

Xmit Parity Errors

The number of transmit parity errors.

LAYER 1 GENERAL STATISTICS

Note: Layer 1 general statistics apply to the indicated slot.

Interrupts

The number of hardware interrupts received from the layer 1 hardware device.

Forced Resynchs

The number of times layer 1 has attempted to manually synchronize to the incoming signal.

592 CyberSWITCH

Image 592

Cabletron Systems CSX1000, CSX1200 manual Layer 1 PRI Error Statistics, Layer 1 General Statistics

Contents

USER’S Guide Virus Disclaimer Trademarks DOC Notice Contents Ordering Isdn Service US Only Configuration Tools Cfgedit Security Overview Configuring System Options and Information Configuring Off-node Server Information Configuring Advanced Bridging Configuring Advanced IP Routing Configuring IPX Configuring Snmp Configuring Other Advanced Options System Verification Problem Diagnosis LED Indicators System Messages System Statistics Routine Maintenance Cfgedit Map Using this Guide Documentation SET Cfgedit MAP Cfgedit Screens Guide ConventionsUser’s Guide CyberSWITCH System Overview Cyberswitch Cyberswitch Network Unique System Features Isdn Cyberswitch Radius Interoperability OverviewInteroperability Protocols Interoperability Devices Security Overview Network Interface Overview Isdn System Components Remote Isdn Devices Switches Supported Safety Considerations Hardware Overview System Platforms CSX1000 and NE Link 1000 a Network Express Product CSX1001, shown below, is equivalent to the NE Link 1000 B2 Workgroup Remote Access Switch System Characteristics EMI CSX1200 CSX1204 BRI Version Cabling Information LAN AccessAUI Pin Signal Function Transmit + Receive + No Connect WAN Access Basic Rate Interface Pin Signal Function Carrier Detect Ring IndicatorReceive Data Transmit Data CSX1200-E11-MOD System Modules System Modules CSX1200-U4-MOD Configuration Files Software OverviewOverview System Software Operational Files User Level Security Files System Installation Accessing the CyberSWITCH Workgroup Remote Access Switch Ordering Isdn Service US only Ordering NI-1 Lines Using EZ-ISDN CodesOrdering NI-1 Lines Using NI-1 Isdn Ordering Codes Ordering BRI Isdn Lines Using Provisioning Settings Provisioning Settings for AT&T 5ESS Switches NI-1 AT&T Custom Point-to-Point AT&T 5ESS NI-1 Service UnrestrictedCSV limit CSV NB limit CSD limit CSD NB limit Any CSV limitCSD limit Provision Settings for Northern Telecom DMS-100 Switches Version Functional Yes Number of call AppearancesBasic Information for Ordering PRI Isdn Lines Type of Switch DisabledOption Local Bell Operating Company Sprint Hardware Installation PRE-INSTALLATION RequirementsChoose a suitable setup location Verify administration console requirements Installing the CSX1200-E11-MOD Installing the CSX1200-U4-MOD Cabling Accessing the Cyberswitch Making ConnectionsDirect Connection NULL-MODEM Connection to a PC Changing the Baud Rate Remote Connection Using Telnet Remote Connection Using a Modem Establishing AN Administration Session Powering on Admin Accessing the Release Notes Upgrading Software Upgrading System SoftwareCD File Structure Product Country or Directories Switchtype Upgrading Software Local Software Upgrade Remote Software Upgrade This message is displayed Flash recover Console Messages during SSB Upgrade Change Defaults to Secure System Return Configuration to Factory Defaults Basic Configuration Configuring Basic Bridging Configuration Tools Executing Cfgedit Saving Cfgedit Changes Dynamic ManagementExecuting Dynamic Management Utility Dynamic Management Commands Saving Dynamic Management Changes Default Configuration Using the Network Worksheets Using the Configuration Chapters Configuring Resources Using Cfgedit Configuring Resources and LinesResources United States Resource Configuration Elements Resource Background Information PPP Configuring Lines Using Cfgedit Lines Multiframe CRC Characteristic PRI/T1 lines E1 lineCommonChannel Line Configuration Elements Auto TEI Directory Numbers Switch Type Number of Data Number of SPIDsDMS100 custom NI-1 Service Profile ID Spid Robbed Bit Signaling is not supported for the CyberSWITCH Commport Information Line Background Information Configuring a Subaddress Using Cfgedit Subaddress Configuration ElementsSubaddresses Subaddresses Background Information Configuring Basic Bridging ENABLING/DISABLING Bridging Using CfgeditSelect Enable/Disable Bridging MAC Layer Bridging Configuration Elements MAC Layer Bridging Background Information Enabling IP Using Cfgedit Configuring Basic IP RoutingInternet Protocol IP Option IP Operating Mode IP Option Configuration ElementsConfiguring the IP Operating Mode Using Cfgedit IP Background Information IP Operating Mode Configuration Elements IP Operating Mode Background Information Configuring Interfaces Using Cfgedit IP Network Interfaces USER’S Guide Network Interface Configuration Elements MTU Transmit Broadcast IP Address Default switch for numbered WAN interfaces IP RIP Receive Control IP Network Interface Background Information IP Network Interface Type Associated Remote Device IP Host RFC1294WAN Direct Host IP Host RFC1294 Hdlc Bridge USER’S Guide Example 1 LAN, WAN and WAN Direct Host Interfaces Example 2 LAN, WAN UnNumbered, WAN Remote LAN Interfaces IP RIP and the IP Network Interfaces Isdn Isdn IP RIP Over Dedicated Connections SITE3 Network Flattening Redundant Configurations for BackupProxy ARP Secondary IP Addressing Example IP Host Communications in Flattened Networks Configuring Static Routes Static Routes IP address for the destination network or host Static Route Configuration Elements Workgroup Remote Access Switch Isdn Static Route Background Information Configuring Default Routes Default RoutesDefault Route Configuration Elements ENABLING/DISABLING IP RIP Using Cfgedit Routing Information Protocol RIP Option IP RIP Configuration Elements IP RIP StatusIP RIP Background Information LAN Configuring Security Level Security Security Overview Security Level System Options and Information Device Level Databases User Level Databases Network Login InformationOFF-NODE Server Information Configuring Security Level Database Device Level User Level Administration Security On-Node Yes Configuring no Security Using Cfgedit No Security Device Level Security Configuring Device Level Security Using CfgeditDevice Level Security Background Information User Level Security Configuring User Level Security Using CfgeditUser Level Security Background Information User Level Security Isdn Responding to Login Prompts Making a Telnet Connection Configuring Device and User Level Security Using Cfgedit Device and User Level SecurityTacacs ACE Device and User Level Background Information Configuring System Options Using Cfgedit Configuring System Options and InformationSystem Options System Options Configuration Elements System Options Bridge MAC Calling Line Id Authentication Address PAP Chap System Options Background Information PAP Chap Configuring System Information Using Cfgedit System Information Configuration ElementsSystem Information Optional Calling Line Id Configuring Administrative Sessions Using Cfgedit Administrative SessionSystem Information Background Information Administrative Session Configuration Elements Administrative Session Background Information Emergency Telnet Server Port Number Background Information Configuring AN ON-NODE Device Database Configuring Device Level DatabasesON-NODE Device Database Configuring ON-NODE Device Entries ON-NODE Device Entries On-node Device Entries No pvc configured for Device DAN SVC 0.0 Routing Device ON-NODE Device Database Configuration Elements DIAL-OUT Phone Numbers Chap Secret Outbound Authentication RIP/SAP Appletalk Information Configuration Elements Bridge Information Configuration Elements ON-NODE Device Database Background Information Bridging with Hdlc Bridge Devices IP Routing with Hdlc Bridge Devices Security Mode On-node Device Table Configuration DataLine Id IP Routing with IP Host Devices RFC1294 IP Routing with PPP IP Devices Using IpcpPAP or Chap PAP Password or Bridging with PPP Bridge Devices Using BCPIP Routing with PPP Bridge Devices Using BCP Configuring OFF-NODE Device Database Location Using Cfgedit OFF-NODE Device Database Location OFF-NODE Device Database Location Configuration Elements OFF-NODE Device Database Location Background Information User Level Authentication Database Location Configuring User Level DatabasesConfiguring Authentication Database Location Using Cfgedit User Level Authentication Database Location Configuring OFF-NODE Server Information Multiple Administration Login NamesName John Doe Name mynode1 Address Remote Office1 Type communications server VRA Manager Authentication Server Configuring VRA Manager Authentication Server Radius Authentication Server VRA Manager Authentication Server Configuration ElementsVRA Manager Authentication Server Background Information Configuring a Radius Authentication Server Displays the current Radius server configuration data Radius Authentication Server Configuration Elements Radius Authentication Server Background Information Tacacs Authentication Server Configuring a Tacacs Authentication Server Tacacs Authentication Server Configuration Elements Tacacs Authentication Server Background Information ACE Authentication Server Configuring AN ACE Authentication Server ACE Authentication Server Configuration Elements ACE Authentication Server Background Information Network Login General Configuration Configuring Network Login InformationConfiguring General Network Login Information Using Cfgedit Network Login General Configuration Background Information Configuring Network Login Banners Using Cfgedit Network Login BannersNetwork Login Banners Background Information Login Configuration Specific to Radius Server Configuring Radius Server Login Information Using Cfgedit Login Configuration Specific to Tacacs Server Configuring Tacacs Server Login Information Using Cfgedit Login Configuration Specific to Tacacs Server Login Elements Specific to Tacacs Advanced Configuration Configuring Alternate Accesses Configuring Alternate Accesses Dedicated AccessesConfiguring a Dedicated Access Using Cfgedit Dedicated Access Configuration Elements Dedicated Access Background Information Accesses Configuring AN X.25 Access Accesses USER’S Guide Configuration Elements Lapb Configuration Elements Timers Maximum Window Size Nonstandard Default Transmit Window Size PVC Configuration Elements Access Background Information B1 B2 Frame Relay Accesses Configuring a Frame Relay Access Configuring a PVC Frame Relay General Configuration Elements Frame Relay PVC Configuration Elements LMILMI Format Dlci Value PVC Name Frame Relay Access Background Information Local Management Interface Overview Allowed Not Allowed Configuring Advanced Bridging Bridge Dial OUT Under ISDN, select Dial Out Phone Number Bridge Mode of Operation Spanning Tree Protocol Bridge Mode of Operation Background Information Configuring Bridge Filters Using Cfgedit Bridge Filters Protocol Definition Commands Source MAC Filter CommandsDestination MAC Filter Commands Protocol Filter Commands Bridge Filter Configuration Elements Packet Data Filter CommandsLsap in HEX Filter Type Maximum Number of Each Bridge Filters Background InformationFilter Destination MAC Protocol Definitions Unrestricted Mode Bridge Filters Source Discard Connect Destination Protocol Packet USER’S Guide Filter Action Distribution Result List Packet matching this filter will not be forwardedOn any LAN port. The packet will be sent to remote Sites connected over the WAN according to Restricted Mode Bridge Filters Restricted Mode Forwarding Action Workgroup Remote Access Switch Filter Distribution Result Action List Packet matching this filter will only be forwardEd on the LAN ports. The packet will not be sent to Any remote sites connected over the WAN Configuring a Destination MAC Address Filter Preliminaries Discard Connect Configuring the Known Connect List Known Connect List Known Connect List Configuration Elements Known Connect List Background Information Configuring Advanced IP Routing Static ARP Table Entries Configuring Static ARP Table Entries Using Cfgedit Static ARP Table Entries Configuration ElementsStatic ARP Table Entries Select Static ARP Table Entries from the IP menu Isolated Mode Static Route Lookup VIA Radius Static Route VIA Radius Configuration Elements Configuring AN IP Address Pool Using CfgeditIP Address Pool Configuration Elements IP Address Pool IP Filters Initiating the IP Filter Configuration Using CfgeditIP Address Pool Background Information Configuring Packet Types Using Cfgedit Mask TCP UDP Icpm Specify a control value any, established, or not established Select Icmp Type Configuring Forwarding Filters Select Add a Forwarding Filter Configuring Connection Filters Configuring Exception Filter Applying Filters Select IP InterfacesSelect Apply Global Forwarding Filter Select Device Level Databases Select On-node Device Entries IP Filters Configuration Elements TCP and UDP Ports NEQRange IP Filters Background Information Packet Types Forwarding Filters Connection Filters Exception Filters Application to Network Interfaces Common Portion Limitations Example of AN IP Filter Configuration FTP WWW Sfvra Forward Configuring a Dhcp Relay Agent Using Cfgedit Dhcp Relay Agent Dhcp Configuration Elements Dhcp Background Information Bridge to Bridge Environment Router to Bridge Environment IP Router to IP Router with Relay Agents on both USER’S Guide Remote Bridge to IP Router w/Relay Agent = WAN Rlan Dhcp Proxy Client Configuring the Dhcp Proxy ClientSelect Dhcp Proxy Client Dhcp Proxy Client ENABLE/DISABLE Flag Sample Configuration IP Router with Dhcp Proxy Client Configuration for IP Router Chloe Configuring IPX Configuring IPX Information IPX Option Configuration Element ENABLING/DISABLING IPX Using CfgeditIPX Routing Option Configuring the IPX Internal Network Number Using Cfgedit IPX Internal Network Number Configuration ElementIPX Internal Network Number IPX Option Background Information Configuring IPX Network Interfaces Using Cfgedit IPX Network InterfacesIPX Network Number Background Information LAN WAN Displays the current IPX network interface data IPX Network Interface Configuration Elements SAP IPX Network Interface Configuration Elements IPX Network Interface Background Information IPX Routing Protocol Configuration Elements Configuring IPX Routing Protocols Using CfgeditIPX Routing Protocols IPX Routing Protocol Background Information SAP Special Considerations Remote LAN Interface Configuring IPX Static Routes Using Cfgedit IPX Static Routes IPX Static Routes Configuration Elements IPX Static Routes Background Information IPX Netware Static Services Configuring IPX Netware Static Services Using Cfgedit IPX Netware Static Services Configuration Elements Configuring IPX Spoofing Using Cfgedit IPX Netware Static Services Background InformationIPX Spoofing IPX Spoofing Configuration Elements IPX Spoofing Background Information Watchdog Protocol Configuring IPX Type 20 Packet Handling Using Cfgedit IPX Type 20 Packet Handling IPX Isolated Mode IPX Type 20 Packet Handling Configuration ElementsConfiguring IPX Isolated Mode Using Cfgedit IPX Isolated Mode Configuration Elements IPX Isolated Mode Background Information Displaying WAN Peer List Configuring Triggered RIP/SAP Global Timers Using Cfgedit IPX-SPECIFIC Information for Devices Configuring IPX DevicesTriggered RIP/SAP Background Information IPX-Specific Information for Devices SPX Watchdog Spoofing Menu Enable Bridging and disable Make calls for bridge data IPX Configuration Elements for Devices IPX Background Information for Devices Configuring Snmp Configuring Snmp Configuring Snmp Snmp Configuration Elements Snmp Background Information WAN Workgroup Remote Access Switch USER’S Guide Enabling Appletalk Routing Using Cfgedit Configuring Appletalk RoutingAppletalk Routing Option Appletalk Routing Option Configuration Element Configuring Appletalk Ports Using CfgeditAppletalk Ports Appletalk Routing Background Information Appletalk Ports Configuration Elements Appletalk Ports Background Information Overview Configuration Configuring Appletalk Static Routes Using CfgeditAppletalk Static Routes Considerations Appletalk Routing Static Routes Configuration Elements Configuring Appletalk Capacities Using CfgeditAppletalk Capacities Configuration Elements Appletalk Capacities Appletalk Isolated Mode Configuring the Appletalk Isolated Mode Using CfgeditAppletalk Isolated Mode Configuration Elements Appletalk Capacities Background Information Configuring the Throughput Monitor Using Cfgedit Configuring Call ControlThroughput Monitor Throughput Monitor Configuration Elements Condition Trigger Number Window Size Utilization Throughput Monitor Background Information90% Overload Condition Monitoring Idle Condition Monitoring Configuring the Call Interval Parameters Using Cfgedit Call Interval Configuration ElementsCall Interval Parameters Call Interval Background Information Configuring Monthly Call Charge Using Cfgedit Monthly Call Charge Configuration ElementsMonthly Call Charge Monthly Call Charge Background Information Call Restriction Configuration Elements Configuring Call Restrictions Using CfgeditCall Restrictions Call Restrictions Call Restrictions Background Information Configuring Bandwidth Reservation Bandwidth Reservation = CentralSite Bandwidth Reservation Configuration Elements Select Bandwidth Reservation Semipermanent Connections Configuring Semipermanent Connections Using CfgeditBandwidth Reservation Background Information Semiperm Call Device Commands Semipermanent Connections Configuration ElementsSemipermanent Connections Background Information Call Restrictions Throughput Monitor Configuring VRA Manager for Call Control Using Cfgedit VRA Manager AS a Call Control Manager Background Information LIMITATIONS/CONSIDERATIONS PPP Configuration Configuring Other Advanced OptionsConfiguring PPP PPP Configuration Elements PPP Background Information PPP Reference Documents Default Line Protocol Configuring Default Line Protocol Using CfgeditDefault Line Protocol Configuration Elements Default Line Protocol Background Information Configuring LOG Options Using Cfgedit LOG Options Configuration ElementsLOG Options UDP Port LOG Options Background Information CDR LOG Report Overview Call Detail Recording Events Event Report Contents Connect Event Report Contents Reject Event Report Contents Disconnect Event Report ContentsSystem Up Event Report Contents Verify Event Report Contents Configuring Compression Options Using CfgeditCompression Options Configuration Elements Compression Options Compression Options Background Information Compression and CCP Configuring Tftp Tftp Tftp Configuration Elements Tftp Background Information Configuring File Attributes File Attributes Configuration ElementsFile Attributes File Attributes Background Information Users Report Files StatFiles CfgFiles Other Files File category File types included in the categoryRPRTLOG.1 STATLOG.1 Troubleshooting System Verification System Verification Verifying Hardware Resources are Operational Verifying WAN Lines are Available for USE Verifying LAN Connection is Operational Verifying Bridge is Initialized Verifying IP Router is Initialized Verifying a Dedicated Connection Verifying a Frame Relay Connection Verifying Remote Device Connectivity Verifying AN X.25 ConnectionVerifying MULTI-LEVEL Security Ping 100.0.0.2 return Verifying IP Host Mode is Operational Verifying IP Host Mode is OperationalVerifying IP Host is Initialized Verifying IP Routing Over Interfaces Verifying IP Routing Over a LAN Interface Verifying IP Routing Over a WAN Interface 100.0.0.1 100.0.0.0 Host B 192.100.1.3 Host a 100.0.0.2 Verifying IP Routing Over a WAN Direct Host Interface Verifying IP Routing Over a WAN Remote LAN Interface Verifying IP Routing Over a WAN Unnumbered Interface Verifying IP Filters Verifying IP RIPIp filter trace discard return Verifying IP RIP is Initialized Verifying IP RIP Output Processing on a LAN Interface Verifying IP RIP Input Processing on a LAN Interface Verifying IP RIP Output Processing on a WAN Interface CSX1200 Router Dedicated Connection 100.1.1.1 192.1.1.1 Verifying IPX Router is Initialized Verifying IPX Routing is Operational Verifying AN IPX Remote LAN Connection Verifying IPX Routing Over a LAN ConnectionXxxx Verifying the Appletalk Routing Feature Verifying IPX Routing Over a WAN ConnectionVerifying Triggered RIP/SAP Verifying Appletalk Routing is Initialized Verifying Appletalk Routing is Operational Verifying Appletalk Routing Operation Over a WAN Connection Verifying Snmp is Operational Verifying the Dial OUT Feature Verifying Call Detail Recording Verifying Reserved Bandwidth is Operational Verifying Compression is OperationalVerifying PPP Link Failure Detection is Operational Verifying Dhcp Relay Agent Verifying Dhcp Relay Agent Initialization Verifying the Relay Agent is Enabled Verifying the Relay Agent is Operational Verifying Dhcp Proxy Client Verifying Dhcp Proxy Client Initialization Verifying the Proxy Client is Operational Verifying the Proxy Client is EnabledUDP Ports Verifying a Semipermanent Connection Verifying Proxy ARP is Operational Verifying Proxy ARP is Operational Problem Diagnosis General ProceduresProblem LAN Adapter IP Routing Initialization Bridge InitializationWAN Line Availability Out Svc 1 slot #, port # Dedicated Connections Frame Relay Connections Connections Remote Device Connectivity Set-up MULTI-LEVEL Security DisabledLAN Attachment IP Host Mode Operation Over the LAN Connection IP Host ModeIP Host Initialization IP Routing Over Interface Connections IP Host Mode Operation Over the WAN ConnectionIP Routing Over the LAN Interface Connection IP Routing Over a WAN Interface Connection IP Routing Over a WAN Direct Host Interface Connection IP Routing Over a WAN Rlan Interface Connection IP Routing Over a WAN Unnumbered Interface Connection If you are still experiencing problems IP RIP Initialization IP RIP Output Processing on a LAN Interface IP RIP Input Processing on a LAN Interface IP RIP Output Processing on a WAN Interface IP RIP Input Processing on a WAN Interface IPX Routing Initialization IPX RoutingIPX Routing Over the LAN Connection IPX Routing Over the Remote LAN Connection IPX Routing Over the WAN Connection IPX Routing and Service Tables Triggered RIP/SAP Start UP Appletalk RoutingTriggered RIP/SAP Operation Appletalk Routing Initialization Appletalk Routing Operational Over the LAN Connection USER’S Guide Appletalk Routing Operational Over the WAN Connection Snmp CyberSWITCH does not generate Snmp Trap PDUs Set Up Dial OUT Call Detail Recording Successful Negotiation CompressionPeer Protocol-Rejects CCP Relay Agent Initialization CyberSWITCH does not have Compression EnabledEnabling the Relay Agent Relay Agent Operation Proxy Client Initialization Enabling the Proxy Client Proxy Client Operation Proxy ARP Operation Proxy ARP Operation LED Indicators Local Area Network LED Indicators PRI LED Indicators Lanview Leds CSX1200-E11-MOD Receive LEDs OFF Service Indicator Service Indicator Remains LIT Service Indicator Blinks OUT SVC LAN Xmit Error Alarm Leds PRI only Alarm LEDs PRI Only System Messages Informational Messages Boot Messages Initialization MessagesNormal Operation Messages Status Messages System Message Summary Error MessagesSpanning Tree Messages Port LAN Adapter, operating in remote mode only Port LAN Adapter, operating in local and remote modeCall has exceeded the configured maximum duration Adapter #’x’ failed to respond from bootstrap Attempting to load FileName for Upgrade Attempt to initialize unconfigured DM card in slot slot #Auth ACE Could not create service file Auth ACE Could not write service file Auth ACE Encryption configured for DES not supported Auth ACE Error receiving server log message acknowledgmentAuth ACE Login rejected user user name Auth ACE Node verification received Client initialized Auth Radius Login rejected device device name Auth Radius IP Host rejected IP Host id IP host IdAuth Radius IP Resolve rejected IP Address IP address Auth Radius PAP rejected device device name Auth Tacacs Login rejected user user name Auth Warning code 0001 TimeoutAuth Warning code 0004 No authentication node available Auth Warning code 0007 Authentication mode mismatch Booting System Software Bootstrap came alive on DM card in slot slot #Bootstrap came alive on WAN card in slot slot # Bad auth result in smgrauthaanotify for device device name Call Restrictions have been disabled by user command Call Restrictions have been enabled by user commandCalculating CRC’s Calling Line ID Failure, Duplicate ID calling line Id Call Restriction statistics reset for new day Call Restriction statistics reset for new monthCall Restrictions will allow calls to be made this hour Call Restrictions will allow calls to be made Workgroup Remote Access Switch Cause cause code received for Dlci dlci index Cause Code EventCCP Internal Decompression Failure CCP Option Negotiation Failure, Non-Convergence detected Chap Authentication Failure remote device not responding Channel in use in Hostcallrequest Configured adapter # ’x’ type does not exist Couldn’t find speech service slot #, port #Current monthly charges reset for new month CNTR-TMRTimed out waiting for TMR number interrupt Dedicated connection down slot #, port # DHCP-P Failed to close UDP port x, erc = yDHCP-P Failed to open UDP port for first Dhcp client DHCP-P Failed to open UDP port x, erc = y DHCP-P Proxy Client disabled DHCP-P Proxy Client enabledDHCP-R Relay Agent disabled DHCP-P Proxy Client initialization failed DHCP-R Relay Agent enabled DHCP-R Relay Agent initialization failedDHCP-R UDP port 67 closed DHCP-R UDP port 67 opened DM card in slot slot # signals it is operational DM card type configured in slot slot # does not existDM card in slot slot # will not come out of reset DM upgrade started. Board=board #, Modem=modem # DM upgrade success. Board=board #, Modem=modem # Downloading Bootstrap to DM card in slot slot #Edrv transmit error error code DSL test failed to establish Layer 1, port=port # Error closing file ’s’ Error downloading bootstrap program to adapter #’x’Error downloading operational software to adapter ’x’ Error during channel initialization Access access index Error mapping WAN adapter #’x’ into Host memory map Error parsing old WAN Direct Host interface bad formatError opening file \system\ethernt2.bin Error programming adapter #’x’ hardware Error reading sdconf.rec file Error requesting slot activationError sending message to Call Control Facility not subscribed Slot=slot # Port=port # Failed to obtain Terminal info in smgrprocterminalauthsess Failure during read of file ’s’Failure during Static RAM test on adapter # ’x’ Failure to allocate enough memory for Xilinx load file USER’S Guide File Access Err Formatting Flash MemoryFrietf detected PPP protocol from NAME, shutting down PVC Frame Relay event queue full Installing File Set into Flash Memory Interrupt fault on WAN Adapter in Slot slot #FrUtl No registered device for Dlci dlci index Initial TDM Clock Master slot#, line# Invalid Cllm received on Access access index Invalid Password password givenIP Error from ESP datagram discarded IP x.x.x.x not added to the pool Unknown error y IP Default Route not added, invalid next hop IP address # IP Invalid configuration for Network Interface ddIpap ResMem returned invalid device maximum value IP Cannot get system memory for IP Invalid Peer IP Address IP address, WAN IP Stream Closed IP IP host is initialized successfullyIP IP router is initialized successfully IP Network initialized successfully on ddd.ddd.ddd.ddd Ipcp IP Address Pool Out of IP addresses Ipcp Option Negotiation Failure, Non-Convergence detectedIpcp Remote device does not negotiate IP address IP Host Call Dropped XID was not received from remote IP Host Security Rejection Invalid Security ID Id string IP RIP All network interfaces usedIP RIP Buffers allocated IP RIP Initialization failed, unable to allocate buffers IP RIP Unable to open RIP/UDP port IP RIP Unable to register WAN Connection notificationIPX Invalid Ipxwc passed IPX Network initialized successfully on IPX SAP Space available in service table IPX SAP Unable to add service, service table fullIpxwan IPX Internal Network Number must be configured IPX RIP Shutdown complete LAN Adapter Command Timeout LAN Adapter configuration conflictLAN Adapter Fatal Error Reported LAN Adapter HW upgrade may be required LAN Adapter Reset LAN Adapter Response TimeoutLAN Adapter System resource error LAN Init Error LAN Xmit Error LMI alarm on Access access indexLMI alarm reset Access access index LAN Port port # detected shorted LAN media Manage Mode updates have been successfully committed Memory Access TimeoutManual intervention required please replace LAN card Manual restart initiated on DM board in slot slot # Mismatch of configured and installed DM card in slot slot # Modem modem # of DM card in slot slot # is unusableModem revision on modem modem # of slot slot # failed Negotiation Failure with Semipermanent device Network sent Cause Spid not supported slot #, port # Network sent Status with state = 0, tear down callNo Active Calls Active Sites No Active List entry available in INM Out of LAN Adapter transmit command descriptors Not enough memory for Security moduleOffnode server lookup of Dial Out User failed Outgoing calls barred Slot=slot # Port=port # Auto For over 5 minutes Report problem to Phone company PAP Identification timeout on remote devicePAP Invalid password for name given by remote device Out Svc # slot # , port # PAP Remote device rejected System Information error message PAP Unknown name name given by remote devicePost number, Hdlc #number External Loopback Test Failed Post number, Hdlc #number Internal Loopback Test Failed RBS LIFAddTimer failure RBSoutSMchannel # Timeout waiting for WinkPVC for Dlci dlci index not Active PVC not allocated for dlci index Reattempting to Install File Set into Flash Memory RebootingReplace Lithium Battery Contact your Representative Reserved signal Security Rejection Invalid Password password given Retrying download of DM card in slot slot# in x secondsRx Channel Inactivity Detected Security Rejection Caller did not negotiate security Security Rejection No Password given by caller Security Rejection Timeout on Startup CompleteSemipermanent. Device x disconnected by admin Security Rejection No Protocol List supplied Semipermanent. Device x reconnected by admin Signal for unknown CallCmd task task IdSlot #, port # Cfg Error Snmp Authentication failure, unknown community name SSB Post 27 i960timer82c54FAILURE SSB Can’t read RTC prior to i960 POSTsSSB Couldn’t read RTC during i960 POSTs SSB i960 Post number not equal to i386’s SSB Post 28 i960lan82596sx Failure SSB Post 29 i960lan82503 FailureSSB Post 30 i960permodmem1 Failure SSB Post 31 i960permodmem2 Failure Successfully Loaded Release X.Y Issue Z Switch could not recognize phone number nnnnnnnSystem Clock Fault on Wan Adapter in Slot slot # STP a Blan Topology Change has been detected Tftp Local error #2 Feature not initialized Tftp Local error #3 Server not initializedTftp Local error #4 UDP rejected packet filename Tftp Local error #5 UDP open failed Tftp Local error #13 Received unexpected opcode filename Tftp Local error #14 Bad file nameTftp Local error #15 Bad mode string Tftp Local error #18 Unable to open file filename Tftp Remote error # 0 Text from Remote Host Tftp Remote error # 1 Text from Remote HostTftp Remote error # 2 Text from Remote Host Tftp Remote error # 3 Text from Remote Host Compression subsystem is not enabled Timeout detected on connection establishmentTimeout detected on receiving caller’s number Timeout on Startup Complete Unable to Decrypt Datagram Type mismatch of configured & installed adapter # ’x’Unable to get Digital Modem resource to place call Unable to open \config\devdb.nei file Unable to open Modem Upgrade fileUnable to restore original ISRs for Interrupt interrupt # Unable to Identify a remote device Unexpected error during transmission of LMI frame Unmatched Login TaskUpdating CyberSWITCH from FileName WAN card in slot slot # signals it is operational Watchdog timeout detected on DM board in slot slot # Watchdog timeout detected on WAN board ’x’X25 facilities error, facilities not allowed in PVC X25 facilities error, bad facility length X25 facilities error, reverse charging not accepted X25 facilities error, fast select not availableX25 facilities error, fast select not accepted X25 facilities error, throughput negotiation not allowed X25 facilities warning, NUI not available Zone allocation failed, maximum capacity already configuredZone allocation failed, increase zone table capacity Trace Messages Call Trace Messages Location Causes Call Trace Message Summary Inband treatment has been applied Configure ack slot #-BRD CFG ACK Slot=slot # Init data link slot #, port #, ces Out configure port # Interworking unspecified causeOff-hook warning tone on Origination call address is non-ISDN Received unknown signal value Out init data link slot #, port # , cesRecall dial tone on Received unknown progress value IP Filters Trace Messages PPP Packet Trace Messages Configure Request Configure ACKConfigure NAK Configure Reject Trace Messages Echo ReplyDiscard Request Trace Message Summary X25 Data LCN logical channel number, number of bytes bytes X25 DCE RR LCN logical channel number, number of bytes bytes System is sending a call request to the network Lapb Trace Messages Lapb Trace Message Summary Lapb Sabme Lapb UAOut Lapb Disc Out Lapb DM System Maintenance Remote Management Remote Management Installation and Configuration SITE.2 Usage Instructions Telnet Earlier Releases Usage Instructions Tftp Client PC Users Report Files Statistics Files Config files Other Files Remote Installation with USER2 USER’S Guide System Commands Accessing Administration Services Setting the IP Address Boot Device Commands Accessing Dynamic Management Viewing Operational Information List relnote.txt Viewing Operational Information Status Second column is the potential number of connections Viewing Throughput Information 100 Throughput Monitor Contents Saving Operational Information CONFIGURATION-RELATED Commands Clearing Operational Information Setting the Date and Time Restarting the CyberswitchFile Utility Commands Terminating Administration Sessions Login-Id Appletalk Routing Commands Type State Default zone Network rangeFlags LAN port Distance Zones valid Zone Bridge Commands Call Control Commands Device name must be re-entered Calling phone number at data rate, device PPP Call Detail Recording Commands Call Restriction Commands Dhcp Commands Compression Information CommandsFrame Relay Commands Clears all statistics associated with the fr stat command IP Routing Commands Disables the trace Valid Icmp Echo Reply was received from host ddd.ddd.ddd.ddd Mask used for the destination Age of the route in seconds IPX Routing Commands Ipx ping host ipx address Isdn Usage Commands Isdn usage LOG Commands LAN CommandsPacket Capture Commands All packets will be captured Following is an example pkt display screen Banyan Vines Packet Detail Screen Bridged Packet Radius Commands Radius ipres TCP Commands Snmp CommandsTelnet Commands Used to close the current Telnet connection to a target host Possible send parameters are defined as follows Terminal Commands Tftp Commands Tftp GET Trace Commands Tftp Session UDP Commands User Level Security Commands WAN Commands Commands Clears the statistics for the default VC Connectivity Statistics System StatisticsCall Restriction Statistics Call Statistics Throughput Monitoring Statistics Appletalk Statistics Appletalk Protocol Statistics Number of AppleTalk Echo requests received Count of AppleTalk Echo replies received Number of NBP LookUp Requests received Appletalk Port Statistics Bridge Statistics Call Detail Recording Statistics Compression Related Statistics Compression StatisticsDecompression Related Statistics Dhcp Relay Agent statistics and Dhcp Proxy Agent statistics Dhcp StatisticsCommon Dhcp Statistics Dhcp Relay Agent Statistics Dhcp Proxy Client Statistics Access Related Statistics Frame Relay Statistics Not currently supported PVC Related Statistics LAN Statistics IP Statistics IP Group Statistics Icmp Group Statistics Number of Icmp Destination Unreachable messages received IPX Statistics IPX General Statistics Number of IPX packets received with incorrect checksums IPX RIP Statistics IPX Triggered RIP Statistics IPX Route Statistics IPX Service Statistics IPX Triggered SAP Statistics RIP Global Statistics RIP StatisticsRIP Interface Statistics Snmp Statistics SnmpInReadOnlys TCP Statistics Tftp Statistics Statistics for Server or Remote Initiated Tftp Activity Statistics for Local or Client Initiated Tftp Activity Statistics for ALL Tftp Activity UDP Statistics WAN Frietf Statistics Layer 1 PRI Error Statistics Layer 1 General Statistics WAN Statistics Statistics Virtual Circuit VC Related Statistics Local DTE X.121 address Routine Maintenance INSTALLING/UPGRADING System SoftwareExecuting Configuration Changes Making Changes Using Cfgedit Making Changes Using Manage Mode Configuration Backup and RestoreObtaining System Custom Information Appendices System Worksheets System Worksheets Network Topology Resources System DetailsLines Accesses Authentication Information Frame Relay Information Device Information Bridging and Routing Information IP Routing IPX Routing Appletalk Routing AppleTalk Routing/Port Information Main Menu IPXSnmp PPP FR DBU Physical Resources Menu DES, FealHdlc PPP FR DBU BPS WAN Rlan Options MenuDhcp Snmp FR DBU Security Menu Radius Tacacs ACEIsdn SVC, PVC PPP STAC-L25 VRA Manager TCP port Getting Assistance Reporting ProblemsContacting Cabletron Systems Phone FAX Cabletron Systems System Problem Report To Customer Service FromNumber of Pages Including this Administrative Console Commands Table Command UseDisplays help screen Displays or clears current AppleTalk port statistics Command Use Cdr stats clear Verifies call detail recording servers are configuredClears administration screen Clears current call detail recording statistics Dlci Generates a triggered RIP/SAP update request to Local log file only displays the call detail recording logLog cdr erase Local log file only erases the call detail recording log Changes password for current access level Displays system errors and system messages Displays current software version and hardware resource Displays the current Tftp statisticsRevision information Access or the specified access Specified X.25 access Manage Mode Commands Table Adds/changes/deletes an IPX address from the IPX Ipxspoof Allows you to configure system level spoofing dataAddress pool Manage Mode Commands Table USER’S Guide Cause Codes Table USER’S Guide Cause Codes Table USER’S Guide Workgroup Remote Access Switch USER’S Guide Dec Value Hex Value Cause Unknown Index Br statCDR Cdr 534 cfg Date Cmp 535 commandsDel 524 destfilt Device 162 Device add Ip addrpool 535, 537 IP filters 241 Ipcp Isdn Lan 545 LAN adapterLan test 355 Lanview LEDs 420 Lapb Led status 518 line NTT INS STAC-LZS Restart 523 restore SentrySpid Srcfilt Term 554 term set 357 terminal mode Udp Wr 52, 521 ws 52 X25