Verona VECTIM304, VECTIM365 Switching the control on, Elements setting, Using the Low Power Scale

Page 10

	Use & Care Manual

		ENGLISH

CONTROL INSTRUCTIONS FOR USE	The display (ref.4) and the “Peacock Tail” (ref.6) show
	the power level, updated in real time.

WARNING

This touch control works using optical light sensing technology. When first connecting electrically or after a power failure, any direct strong light over the sensor area may affect the touch control functionality. When powering on the unit make sure that no strong light is shining direct over the touch control zone, it can compromise the start-up sensor calibration resulting in an unresponsive touch control.

When the cooktop is connected to the electrical voltage supply all lights and digits turn on to indicate a proper activation. This operation will be completed after few seconds, the control turns off automatically. Now the cooktop is ready for operations.

Switching the control on

Eventually hold the [LOCK] key in case the commands are locked (see that the lock led is on and turns off after a few seconds).

Touch the main [ON/OFF] key in order to make each single zone available for selection.

All the displays show power level “0”, if no actions are performed the control shuts down again after about 10 seconds.

Elements setting

Touch the proper [ON] key (ref.2) in order to select the desired zone: the HOT SURFACE (ref.3) indication starts flashing, waiting for a user input.

5a

4

2

1

3

Figure. 6

Touch the slide bar to set the power level (levels 0 to 9 are available), moving the finger along it or directly touching the desired value.

After a 5 seconds time-out the value is accepted, the HOT SURFACE led (ref.3) stops flashing and gets steady. The “Peacock Tail” disappears after some seconds more.

Touch [ON] key to confirm the value before the time-out expires.

The following picture represents the Full Power Scale whereas the control uses all the available power range, from 0% up to the 100% corresponding to level 9.

Level 4 corresponds to 15% of the available power.

6

7

Figure. 7

Using the Low Power Scale

Once a cooking zone has been selected, touch the [LOW TEMP] key (ref.8) in order to enable the Low Power Scale (ref.9) then set the power level in the usual way.

9

8

Figure. 8

10

Image 10

Contents VECTIM365 VECTIM304 Page Models may be powered at InstallationManual Safety Instructions Cooktop SafetyPersonal Safety VECTIM304 Approval code 812T40IP or 812T40NP Models and Part IdentificationVECTIM365 Approval code 812V50IQ or 812V50NQ Heat Position 4 Power level display Touch Control details Full optionsTouch Control Characteristics for every model Low Temperature Function Advice on cookingSetting Recommended Use Power Level Temperature F CUsing the Low Power Scale Switching the control onElements setting Level 4 corresponds to 15% of the available powerSetting the timer Switching an element offHot surface indicator light Fast Boil Booster functionRest Heat Beep confirms that the new value was accepted correctlyInduction Cooktop Operation Cookware noise Power SharingBefore Using the Cooktop for the First Time Five burner cooktops are divided into 3 zonesCookware Pots and pans and how to use themHow Induction heating works Cleaning the Cooktop Fuse or reset circuit breaker TroubleshootingTo the cooktop. Have electrician replace Failures declarations Assistance or ServiceFc Allow the cooktop cool down Boutons de commande/Caractéristiques Avertissements Pour ’INSTALLATION ElectriqueBoutons de commande par effleurement Les modèles peuvent être actionnés à 240V ou àPrécaution de Sécurité Securite DE LA Table DE CuissonSecurite Personnelle Utilisez un extincteur uniquement siVECTIM304 Code d’approbation 812T40IP ou 812T40NP Modèles et nomenclature des piècesVECTIM365 Code d’approbation 812V50IQ or 812V50NQ Sécurité enfants Position 11 MinuterieBoutons de commande/Caractéristiques des différents modèles Fonction basses températures Valeurs de réglage recommandéesConseils pour la cuisson Niveau de puissance Température F CRéglage des éléments Allumer le panneau de commandeUtilisation de la gamme de puissance réduite Fonction cuisson rapide booster Éteindre un élémentVoyant indicateur surface très chaude Fonction de verrouillage des touchesChaleur de veille CaractéristiquesBatterie de cuisine « bruyante » Fonctionnement de la Table de CuissonPartage de puissance Avant D’UTILISER LA Table DE Cuisson Pour LA Premiere FoisComment fonctionne le chauffage à induction Utilisation des casserolesNettoyage de la Table de Cuisson Pannes Problème Cause Remèdes possiblesAssistance ou Service Après-Vente Indications d’erreurAdvertencias Para LA Instalación EléctricaInstrucciones de Seguridad Seguridad DE LA Placa DE CoccionCuando utilice la placa de cocción Seguridad PersonalUtilice un extintor solo si Cuando utilice la placa de cocción sobra el hornoVECTIM304 Código de aprobación 812T40IP ó 812T40NP Modelos y nomenclatura de piezasVECTIM365 Código de aprobación 812V50IQ ó 812CV50NQ Mandos táctiles Vista detallada con todas las opciones Position 6b Indicator de habilitación de elemento dobleNiños Teclas de mando/Características de los diferentes modelos Función Baja Temperatura Consejos de usoValores de regulación recomendados Nivel de potencia Temperatura F CRegulación de los elementos Encender el cuadro de mandosUtilización de la gama de potencia reducida Función booster Apagar un elementoLed indicador de superficie muy caliente Función de bloqueo de seguridad de las teclasCalor de reposo CaracterísticasRuidos de recipientes de cocción Funcionamiento de la Encimera de InducciónDistribución de energía Antes DE Utilizar LA Placa POR Primera VEZFuncionamiento del calentamiento por Tipos de recipientes y su usoLimpieza de la Placa de Cocción Solución de Problemas Problema Causa Posible soluciónIndicaciones de error Servicio de Asistencia TécnicaEuroChef USA, Inc

Related manuals

Manual 28 pages 1.8 Kb