FCI Home Appliances COGB33060/BL Low Flame Adjustment, Burner Ignition and Autoreignition

Page 18

Cooktop & Installation Manual

Model COGB ENGLISH

Low Flame Adjustment

DANGER

a flame and to automatically relight following a loss of flame due to a draft or other adverse condition. This feature is provided as a convenience and is not intended as a safety feature.

Lighting gas burners with a match is dangerous. You should match light the cooktop burners only In an emergency.

Light a match and hold the flame near the burner you want to light. Wooden matches work best. Push in and turn the control knob slowly.

Be sure you are turning the correct knob for the burner you are lighting.

NOTE:

If the burner does not light within five seconds, turn the knob off and wait one minute before trying again.

WARNING

If you attempt to measure the inner cone of the flame, please use caution.

Burns could result.

This appliance is shipped from the factory with low and medium flame settings adjusted.

If further adjustment is necessary, proceed as follows:

1.Light burner and set control knob for low flame.

2.Remove control knob from valve stem.

3.Insert a slender, thin-blade screwdriver into the recess at centre of valve stem and engage blade with slot in adjusting screw.

4.Turn center stem adjusting screw to set flame size.

clockwise to reduce

counterclockwise to increase

5.Replace control knob when adjustment is completed.

Proper adjustment will produce a stable, steady blue flame of minimum size. The final adjustment should be checked by turning knob from high to low several times without extinguishing the flame.

This adjustment, at low setting, will automatically provide the proper flame size at medium setting. After Conversion Steps have been completed, check the appearance of each burner's flame at the Hi and Lo settings, if the flames appear too large or too small review each step to make sure it was completed correctly.

Burner Ignition and Autoreignition

This appliance is equipped for electronic auto- reignition by means of a spark igniter located near each burner. The burners are designed to light at any valve rotation that admits sufficient gas flow to support

Burner Ignition

Cooktop Spark Ignition. When you turn the cooktop knob to LITE, the spark igniter makes a series of electric sparks (ticking sounds) which light the burner. During a power failure, the burners will not light automatically. In an emergency, a cooktop burner may be lit with a match by following the steps below.

The Burner Flames

Turn each burner on. Flames should be blue in color with no trace of yellow. The burner flames should not flutter or blow away from the burner The inner cone of the flame should be between 1/2" and 3/4" long.

 

COUNTERCLOCKWISE

 

 

TO INCREASE

 

 

FLAME SIZE

CLOCKWISE

 

 

 

 

TO REDUCE

 

 

FLAME SIZE

021

 

VALVE STEM

 

 

Figure 21. Low flame adjustment

-1/2” to 3/4”

COOKTOP BURNER

003

Figure 22. Burner flames

18

Image 18
Contents Installation Manual Page Cooktop & Installation Manual Table of ContentsPlease read all instructions before using this appliance Before Starting InstallationCooktop Installed over Oven Installation Special WarningsProduct Dimensions and Cutout Requirements Important Preparation SuggestionsMobile Home Installation Gas and Electrical Line OpeningSolid surface countertop installation Cut Hazard Cooktop InstallationExcessive Weight Hazard StepDo not Over Tighten Gas Requirement Important Notes for Gas ConnectionNever Tighten to More than 35 ft lbs of Torque Gas Connection Assure all pipe joint connections are gas tightEnglish Pressure Testing Pressure Test MethodElectrical Connection Electrical RequirementsGeneral Information Electrical RequirementsWiring diagram code FA51T40A Models CGB-3001 Replace all Injectors Conversion LP GasConverting Appliance for Use with LP Gas Save the orifices removed from the appliance for future useTo Convert Appliance for Use with NG Pressure Regulator ConversionBurner Ignition Low Flame AdjustmentBurner Ignition and Autoreignition Burner Flames’installateur Tables des matieresAu client Avertissement Spéciaux Avant de Procéder à l’InstallationInstallation de la Table de Cuisson Au-Dessus du Four Que faire si vous sentez une odeur de gazDimensions et Dispositions pour la Découpe Suggestions Importantes de PréparationInstallation autocaravane Ouverture à pratiquer pour câble électrique et tuyau gazInstallation sur un plan de travail à surface solide Risque de coupure Installation de la Table de CuissonRisque du fait du poids excessif ÉtapeBien Serrer Mais PAS Trop Fort Conditions Requires Gaz Installez un emmanchement entre le régulateur et Raccordement du GazRobinet principal Vérification de la Pression Méthode de Test de PressionBranchement Electrique Conditions Requises ElectricitéInformation Général Requises ElectricitéSchéma électrique FA51T40A Modèles CGB-3001 Conversion Gaz PL Conversion de l’Appareil pour Fonctionner au Gaz PLRemplacez les injecteurs de tous les brûleurs Conversion du Régulateur de Pression Pour Utiliser l’Appareil avec du Gaz NatuRel Remplacez tous les injecteurs PL avec desAllumage Brûleur Réglage Petite FlammeAllumage du Brûleur et Ré-allumage Au- tomatique Les Flammes du BrûleurLEA Y Conserve Estas INSTRUCCIONES. Instalador Tabela de ContenidoPagina ClienteQué hacer si detecta olor a gas Advertencias EspecialesAntes de comenzar la instalación Instalación de la placa sobre un hornoDimensiones del Producto y de Encastre Importantes Consejos de PreparaciónInstalación en Casas Móviles Figura 4. Abertura de la línea de gas y electricidadFigura 5. Instalación en encimeras de superficie sólida Peligro de corte Instalación de la Placa de CocciónPeso excesivo PasoFigura Paso Conexión del Gas Requisitos Observaciones importantes para la conexión del gasConexión del Gas Poder cerrar o abrir con facilidad el suministro deAtención Prueba de Presión Método de la prueba de presiónConexión Eléctrica Requisitos Conexión Eléctrica RequisitosConexión Eléctrica Peligro de descarga eléctricaFigura 16. Diagrama eléctrico FA51T40A Modelos CGB-3001 Conversión a Gas PL Conversión del Electrodoméstico para su Uso con Gas PLSustituya todos los inyectores Conversión del Electrodoméstico para su Uso con NGConversión del regulador de presión Encendido de los Quemadores Graduación de la Llama BajaEncendido y Re-encendido de los Que- madores Las llamas del quemadorPage 09FX1810 03/06