FCI Home Appliances COGB33062/SS, COGB33060/BL Special Warnings, Before Starting Installation

Page 4

Cooktop & Installation Manual

Model COGB ENGLISH

IMPORTANT

Special Warnings

Please read all instructions before using this appliance.

Proper installation is your responsibility. Have a qualified technician install this cooktop.

Important:

Observe all governing codes and ordinances.

Write down the model and serial numbers before installing the cook top. Both numbers are on the serial rating plate located on bottom of cooktop box.

Before Starting Installation

Check location where cooktop will be installed. The location should be away from strong drafty areas, such as windows, doors and strong heating vents or fans.

Electrical grounding is required. See "Electrical Requirements"

Assure that electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 - latest edition**, or Canadian Electrical Code, part 1 C22.1 (latest edition)*** and all local codes and ordinances.

Assure that gas connection conforms with local codes and ordinances. In the absence of local codes, installations must conform with American National Standard, National Fuel Gas Code ANSI Z223/NFPA 54 - latest edition** Canadian CAN/CGA_B 149.1 or CAN/CGA-149.2 latest edition**

Copies of the standards listed may be obtained from:

**National Fire Protection Association One Batterymarch Park Quincy, Massachusetts 02269

***CSA International 8501 East Pleasant Valley Rd. Cleveland, OH 44131-5575

NOTE:

This cooktop is manufactured for use with Natural gas or Propane.

To convert to LP (propane) or NG (natural gas), see instruction.

In the gas conversion Kit provided in literature Package. Proper gas supply connection must be Available. See gas supply requirements.

WARNING

BEFORE CONNECT THE APPLIANCE ON THE GAS LINE SUPPLY, ENSURE THAT ITS GAS SET IS APPROPRIATE.

THE TYPE OF GAS ADJUSTED AND SHIPPED FROM THE FACTORY IS INDICATED ON THE RATING PLATE LOCATED ON BOTTOM OF BURNER BOX.

Cooktop Installed over Oven Installation

Only certain specified cooktop and oven models are approved for cooktop over oven installations. Cooktops approved for this type of installation will have an approval label located on the outside of the burner box.

If you do not find this label, contact your dealer to confirm that cooktop is approved.

The label on the bottom of your cooktop lists the cooktop and oven combinations that are approved for this type of installation.

4

Image 4
Contents Installation Manual Page Cooktop & Installation Manual Table of ContentsBefore Starting Installation Cooktop Installed over Oven InstallationPlease read all instructions before using this appliance Special WarningsProduct Dimensions and Cutout Requirements Important Preparation SuggestionsMobile Home Installation Gas and Electrical Line OpeningSolid surface countertop installation Cooktop Installation Excessive Weight HazardCut Hazard StepDo not Over Tighten Important Notes for Gas Connection Gas RequirementNever Tighten to More than 35 ft lbs of Torque Gas Connection Assure all pipe joint connections are gas tightEnglish Pressure Testing Pressure Test MethodElectrical Requirements General InformationElectrical Connection Electrical RequirementsWiring diagram code FA51T40A Models CGB-3001 Conversion LP Gas Converting Appliance for Use with LP GasReplace all Injectors Save the orifices removed from the appliance for future useTo Convert Appliance for Use with NG Pressure Regulator ConversionLow Flame Adjustment Burner Ignition and AutoreignitionBurner Ignition Burner FlamesTables des matieres ’installateurAu client Avant de Procéder à l’Installation Installation de la Table de Cuisson Au-Dessus du FourAvertissement Spéciaux Que faire si vous sentez une odeur de gazDimensions et Dispositions pour la Découpe Suggestions Importantes de PréparationInstallation autocaravane Ouverture à pratiquer pour câble électrique et tuyau gazInstallation sur un plan de travail à surface solide Installation de la Table de Cuisson Risque du fait du poids excessifRisque de coupure ÉtapeBien Serrer Mais PAS Trop Fort Conditions Requires Gaz Installez un emmanchement entre le régulateur et Raccordement du GazRobinet principal Vérification de la Pression Méthode de Test de PressionConditions Requises Electricité Information GénéralBranchement Electrique Requises ElectricitéSchéma électrique FA51T40A Modèles CGB-3001 Conversion de l’Appareil pour Fonctionner au Gaz PL Conversion Gaz PLRemplacez les injecteurs de tous les brûleurs Pour Utiliser l’Appareil avec du Gaz Natu RelConversion du Régulateur de Pression Remplacez tous les injecteurs PL avec desRéglage Petite Flamme Allumage du Brûleur et Ré-allumage Au- tomatiqueAllumage Brûleur Les Flammes du BrûleurTabela de Contenido PaginaLEA Y Conserve Estas INSTRUCCIONES. Instalador ClienteAdvertencias Especiales Antes de comenzar la instalaciónQué hacer si detecta olor a gas Instalación de la placa sobre un hornoDimensiones del Producto y de Encastre Importantes Consejos de PreparaciónInstalación en Casas Móviles Figura 4. Abertura de la línea de gas y electricidadFigura 5. Instalación en encimeras de superficie sólida Instalación de la Placa de Cocción Peso excesivoPeligro de corte PasoFigura Paso Conexión del Gas Requisitos Observaciones importantes para la conexión del gasConexión del Gas Poder cerrar o abrir con facilidad el suministro deAtención Prueba de Presión Método de la prueba de presiónConexión Eléctrica Requisitos Conexión EléctricaConexión Eléctrica Requisitos Peligro de descarga eléctricaFigura 16. Diagrama eléctrico FA51T40A Modelos CGB-3001 Conversión del Electrodoméstico para su Uso con Gas PL Conversión a Gas PLSustituya todos los inyectores Uso con NG Conversión del Electrodoméstico para suConversión del regulador de presión Graduación de la Llama Baja Encendido y Re-encendido de los Que- madoresEncendido de los Quemadores Las llamas del quemadorPage 09FX1810 03/06