FCI Home Appliances COGB33060/BL Mobile Home Installation, Gas and Electrical Line Opening

Page 6

Cooktop & Installation Manual

Model COGB ENGLISH

Mobile Home Installation

The installation of this cooktop must conform to the Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety; Title 24 HUD part 280); or when such standard is not applicable, the Standard for Manufactured Home Installations (Manufactured Home Sites, Communities and Setups), ANSI A225.1 - latest edition, or with local codes.

In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-Z240 - latest edition, or with local codes.

NOTE:

If cabinet has a drawer, a 5-1/4"(13,35 cm) depth clearance from the top of the countertop to the top of the drawer (or other obstruction) in base cabinet is required. The drawer depth may need to be shortened to avoid interfering with the regulator.

24" (61 cm) min. clearance if bottom of wood or metal cabinets is protected by not less than 1/4" (0.6 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel 0.015" (0.04 cm) stainless steel, or 0.024" (0.06 cm) aluminium or 0.020" (0.05 cm) copper. 30" (76.2 cm) min. clearance between top of cooking platform and bottom of unprotected wood or metal cabinet.

13" (33 cm) MAX DEPTH OF UNPROTECTED OVERHEAD CABINETS

MIN 30" (76.2 cm)

5" (12.7 cm) MIN CLEARANCE FROM CUTOUT TO SIDE WALL ON THE LEFT AND RIGHT OF THE UNIT

WALL COVERING CABINETS, AND COUNTERTOP MUST WITHSTAND HEAT UP TO 200 °F

GAS OPENING FOR COOKTOP INSTALLATION

OVER BUILT-IN OVEN 2-9/32" (6 cm) FROM REAR

CORNER OF CUTOUT TO HOLE

4-25/32" (12.15 cm) FROM TOP OF COUNTERTOP TO HOLE (HOLE DIAMETER 1-1/5")(3 cm)

2-19/32" (6.55 cm) OF RIGHT REAR CORNER OF CUTOUT

2-9/32" (6 cm) FROM THE BACK CORNER OF CUTOUT

ELECTRICAL OUTLET

00412" (30.5 cm) BELOW FROM BOTTOM OF COUNTERTOP

Figure 4. Gas and Electrical Line Opening

18" (45.7 cm) MIN HEIGHT FROM

003COUNTERTOP TO NEAREST CABINET ON EITHER SIDE OF UNIT

30" (76.2 cm) MIN (see NOTE)

CLEARANCE FROM COUNTERTOP TO UNPROTECTED OVERHEAD SURFACE

Figure 3. Cutout requirements

6

Image 6
Contents Installation Manual Page Cooktop & Installation Manual Table of ContentsPlease read all instructions before using this appliance Before Starting InstallationCooktop Installed over Oven Installation Special WarningsProduct Dimensions and Cutout Requirements Important Preparation SuggestionsMobile Home Installation Gas and Electrical Line OpeningSolid surface countertop installation Cut Hazard Cooktop InstallationExcessive Weight Hazard StepDo not Over Tighten Gas Requirement Important Notes for Gas ConnectionNever Tighten to More than 35 ft lbs of Torque Gas Connection Assure all pipe joint connections are gas tightEnglish Pressure Testing Pressure Test MethodElectrical Connection Electrical RequirementsGeneral Information Electrical RequirementsWiring diagram code FA51T40A Models CGB-3001 Replace all Injectors Conversion LP GasConverting Appliance for Use with LP Gas Save the orifices removed from the appliance for future useTo Convert Appliance for Use with NG Pressure Regulator ConversionBurner Ignition Low Flame AdjustmentBurner Ignition and Autoreignition Burner Flames’installateur Tables des matieresAu client Avertissement Spéciaux Avant de Procéder à l’InstallationInstallation de la Table de Cuisson Au-Dessus du Four Que faire si vous sentez une odeur de gazDimensions et Dispositions pour la Découpe Suggestions Importantes de PréparationInstallation autocaravane Ouverture à pratiquer pour câble électrique et tuyau gazInstallation sur un plan de travail à surface solide Risque de coupure Installation de la Table de CuissonRisque du fait du poids excessif ÉtapeBien Serrer Mais PAS Trop Fort Conditions Requires Gaz Installez un emmanchement entre le régulateur et Raccordement du GazRobinet principal Vérification de la Pression Méthode de Test de PressionBranchement Electrique Conditions Requises ElectricitéInformation Général Requises ElectricitéSchéma électrique FA51T40A Modèles CGB-3001 Conversion Gaz PL Conversion de l’Appareil pour Fonctionner au Gaz PLRemplacez les injecteurs de tous les brûleurs Conversion du Régulateur de Pression Pour Utiliser l’Appareil avec du Gaz NatuRel Remplacez tous les injecteurs PL avec desAllumage Brûleur Réglage Petite FlammeAllumage du Brûleur et Ré-allumage Au- tomatique Les Flammes du BrûleurLEA Y Conserve Estas INSTRUCCIONES. Instalador Tabela de ContenidoPagina ClienteQué hacer si detecta olor a gas Advertencias EspecialesAntes de comenzar la instalación Instalación de la placa sobre un hornoDimensiones del Producto y de Encastre Importantes Consejos de PreparaciónInstalación en Casas Móviles Figura 4. Abertura de la línea de gas y electricidadFigura 5. Instalación en encimeras de superficie sólida Peligro de corte Instalación de la Placa de CocciónPeso excesivo PasoFigura Paso Conexión del Gas Requisitos Observaciones importantes para la conexión del gasConexión del Gas Poder cerrar o abrir con facilidad el suministro deAtención Prueba de Presión Método de la prueba de presiónConexión Eléctrica Requisitos Conexión Eléctrica RequisitosConexión Eléctrica Peligro de descarga eléctricaFigura 16. Diagrama eléctrico FA51T40A Modelos CGB-3001 Conversión a Gas PL Conversión del Electrodoméstico para su Uso con Gas PLSustituya todos los inyectores Conversión del Electrodoméstico para su Uso con NGConversión del regulador de presión Encendido de los Quemadores Graduación de la Llama BajaEncendido y Re-encendido de los Que- madores Las llamas del quemadorPage 09FX1810 03/06