FCI Home Appliances COGB33061/WH, COGB33060/BL, COGB 33060/L/BL, COGB33062/SS Do not Over Tighten

Page 9

Cooktop & Installation Manual

Model COGB ENGLISH

Step 2

Before installing apply the foam tape.

A tape is provided to seal the cooktop edges to the countertop. Apply tape near inner underside cooktop edge.

Use tape around the entire cooktop perimeter. Cut off excess where tape butt ends.

008

Figure 8.

Step 3

Insert the cooktop centered into the cutout opening. Make sure the front edge of the counter top is parallel to the cooktop. Make final check that all required clearances are met.

burner box front back install the clamp brackets on the lateral position of burner box).

step A place the clamping screws into brackets

step B attach brackets by using the attachment screws on the selected location of burner box, tighten screws just enough to hold brackets in place

step C positioning brackets so that they are with the clamp screw in contact with the counter top bottom

step D tighten attachment screws securely.

step E check that the front edge of the cooktop is parallel to the front edge of the countertop tighten the screw clamping against the countertop.

DO NOT OVER TIGHTEN

010

Figure 10.

009

Figure 9.

Step 4

Four clamp brackets are provided with your unit. After cooktop has been installed into the countertop, install the brackets on the burner box as shown in figure 10.

Install the clamp brackets on the front and back of the burner box bottom (if the cabinet construction does not provide clearance for installing brackets at the

9

Image 9
Contents Installation Manual Page Table of Contents Cooktop & Installation ManualCooktop Installed over Oven Installation Before Starting InstallationPlease read all instructions before using this appliance Special WarningsImportant Preparation Suggestions Product Dimensions and Cutout RequirementsGas and Electrical Line Opening Mobile Home InstallationSolid surface countertop installation Excessive Weight Hazard Cooktop InstallationCut Hazard StepDo not Over Tighten Gas Requirement Important Notes for Gas ConnectionNever Tighten to More than 35 ft lbs of Torque Assure all pipe joint connections are gas tight Gas ConnectionEnglish Pressure Test Method Pressure TestingGeneral Information Electrical RequirementsElectrical Connection Electrical RequirementsWiring diagram code FA51T40A Models CGB-3001 Converting Appliance for Use with LP Gas Conversion LP GasReplace all Injectors Save the orifices removed from the appliance for future usePressure Regulator Conversion To Convert Appliance for Use with NGBurner Ignition and Autoreignition Low Flame AdjustmentBurner Ignition Burner Flames’installateur Tables des matieresAu client Installation de la Table de Cuisson Au-Dessus du Four Avant de Procéder à l’InstallationAvertissement Spéciaux Que faire si vous sentez une odeur de gazSuggestions Importantes de Préparation Dimensions et Dispositions pour la DécoupeOuverture à pratiquer pour câble électrique et tuyau gaz Installation autocaravaneInstallation sur un plan de travail à surface solide Risque du fait du poids excessif Installation de la Table de CuissonRisque de coupure ÉtapeBien Serrer Mais PAS Trop Fort Conditions Requires Gaz Raccordement du Gaz Installez un emmanchement entre le régulateur etRobinet principal Méthode de Test de Pression Vérification de la PressionInformation Général Conditions Requises ElectricitéBranchement Electrique Requises ElectricitéSchéma électrique FA51T40A Modèles CGB-3001 Conversion Gaz PL Conversion de l’Appareil pour Fonctionner au Gaz PLRemplacez les injecteurs de tous les brûleurs Rel Pour Utiliser l’Appareil avec du Gaz NatuConversion du Régulateur de Pression Remplacez tous les injecteurs PL avec desAllumage du Brûleur et Ré-allumage Au- tomatique Réglage Petite FlammeAllumage Brûleur Les Flammes du BrûleurPagina Tabela de ContenidoLEA Y Conserve Estas INSTRUCCIONES. Instalador ClienteAntes de comenzar la instalación Advertencias EspecialesQué hacer si detecta olor a gas Instalación de la placa sobre un hornoImportantes Consejos de Preparación Dimensiones del Producto y de EncastreFigura 4. Abertura de la línea de gas y electricidad Instalación en Casas MóvilesFigura 5. Instalación en encimeras de superficie sólida Peso excesivo Instalación de la Placa de CocciónPeligro de corte PasoFigura Paso Observaciones importantes para la conexión del gas Conexión del Gas RequisitosPoder cerrar o abrir con facilidad el suministro de Conexión del GasAtención Método de la prueba de presión Prueba de PresiónConexión Eléctrica Conexión Eléctrica RequisitosConexión Eléctrica Requisitos Peligro de descarga eléctricaFigura 16. Diagrama eléctrico FA51T40A Modelos CGB-3001 Conversión a Gas PL Conversión del Electrodoméstico para su Uso con Gas PLSustituya todos los inyectores Conversión del Electrodoméstico para su Uso con NGConversión del regulador de presión Encendido y Re-encendido de los Que- madores Graduación de la Llama BajaEncendido de los Quemadores Las llamas del quemadorPage 09FX1810 03/06