Rotel RSX-972 owner manual FM Wire Antenna, AC Input, 12V Trigger Connections, External REM

Page 21

Connect the 300 ohm twin-conductor wire from the loop antenna to the pair of screw termi- nals labeled AM LOOP, attaching one wire to each terminal. It does not matter which wire attaches to which terminal, but make sure that the connections are solid and that the two wires do not touch.

You may need to rotate or otherwise reorient the antenna to find the best position.

NOTE: To use an outdoor antenna, connect its 300 ohm twin-conductor wire to the termi- nals in place of the loop antenna.

FM Wire Antenna

The RSX-972 includes a wire antenna to re- ceive FM signals. In many countries (includ- ing the USA), this antenna is a T-shaped twin- conductor 300 ohm antenna. Remove this an- tenna from the box and connect its two con- ductors to the two screw terminals on the sup- plied 300 ohm to 75 ohm adaptor. Connect the coax plug on the converter to the FM 75 ohm antenna connector on the RSX-972.

For best reception, unfold the T-shaped antenna. There are eyelets at both ends of the T, which allow tacking the antenna to a wall, if desired. Experiment with positioning for best reception.

In some countries, the RSX-972 may be sup- plied with a single wire FM antenna terminated by a 75 ohm coax connector. If your unit is supplied with this antenna, connect it directly to the FM 75 ohm antenna connector.

NOTE: To use an outdoor antenna, connect its 75 ohm coax lead wire (or 300 ohm twin- conductor wire and 300 ohm to 75 ohm adaptor) to the FM 75 ohm connector in place of the indoor wire antenna.

Power and Miscellaneous Connections

AC Input

Your RSX-972 is configured at the factory for the proper AC line voltage in the country where you purchased it (USA: 115 volts/60Hz AC or CE: 230 volts /50 Hz AC ). The AC line configuration is noted on a decal on the back of your unit.

Plug the supplied cord into the AC INPUT receptacle on the back of the unit.

21

NOTE: Memorized settings and video labels will be stored for up to one month if the RSX-972 is disconnected from AC power.

12V TRIGGER Connections

Several Rotel amplifiers offer the option of turning them on and off using a 12 volt trig- ger signal. These two connections provide this 12 volt trigger signal. When the RSX-972 is activated, a 12 volt DC signal appears at these connectors and will turn on amplifiers. When the RSX-972 is put in STANDBY mode, the trigger signal is interrupted and the amplifi- ers will turn off.

EXTERNAL REM IN

This 3.5 mm mini-jack (labeled EXT REM IN) receives command codes from an industry-stan- dard infrared receivers (Xantech, etc.) located in the main listening room. This feature is useful when the unit is installed in a cabinet and the front-panel sensor is blocked. Consult your au- thorized Rotel dealer for information on ex- ternal receivers and the proper wiring of a jack to fit the mini-jack receptacle.

NOTE: The IR signals from the EXTERNAL RE- MOTE IN jack (as well as those from the ZONE REMOTE IN jack) can be relayed to source components using external IR emitters or hard-wired connections from the IR OUT jacks. See the ZONE 2 section of this manual for additional information.

Zone 2 Connection and Operation

The RSX-972 provides Zone 2 multi-room capability, allowing you to enjoy music and operate the system from a second room. From the remote location, you can select a source component (even if different from the source playing in the main listening room), adjust the volume level in the remote zone, and oper- ate the source components.

To use the Zone 2 capability, you need addi- tional components: a pair of speakers installed in the remote zone, an amplifier to drive them, and a third-party IR repeater system.

Zone 2 can be controlled from the main room using RSX-972’s front-panel ZONE button. Op- eration from the remote zone requires the in-

English

stallation of an infrared repeater system (Xantech, Niles, etc.) which relays infrared remote control commands from Zone 2 to the ZONE REMOTE IN input on the back of the RSX-972. Using external IR emitters or hard- wired IR connections, you can also operate source components by remote control from Zone 2.

Several points to keep in mind about the Zone

2 function:

•An infrared repeater system (Xantech, Niles, et al) is required for operation from the remote zone.

•There are two options for the Zone 2 out- put level, selectable from the ON-SCREEN DISPLAY menu system. VARIABLE output gives you full adjustment of the volume level, remembering last previous setting when- ever Zone 2 is activated. FIXED output disables the Zone 2 volume control with the output permanently set to a specified level. This might be useful for sending a line level signal to a preamp or integrated amp with its own volume control or to a distribution amplifier with multiple autoformer-type volume controls.

•The RR-969 remote control supplied with the RSX-972 will operate Zone 2 if used with a repeater system from the remote zone. It can also be programmed to oper- ate Rotel source components via the RSX-972's IR OUT jack.

•Any source component connected to the RSX-972's analog inputs (except the 5.1 CH input) can be sent to the Zone 2 out- puts. ZONE 2 operates independently of the main room. You can select a different source or adjust Zone 2 volume without affecting the MAIN outputs in any way.

•Avoid sending the same infrared command to the RSX-972 front-panel sensor and a Zone 2 repeater at the same time. This means that Zone 2 must be in a different room from the RSX-972.

Zone 2 Power On/Off

Operation

Once master power is applied to the unit by pressing the front-panel POWER button, the RSX-972 provides independent power on/off operation for both zones. Pressing the remote control POWER button in the main room acti- vates or deactivates the RSX-972 in the main

Page 20 Page 22
Image 21
Page 20 Page 22
Contents RSX-972 English Explication des symboles graphiques FrançaisDeutsch RSX-972 Power VOL RR-969 Remote Télécommande RR-969 Fernbedienung RR-969Subwoofer Front L Center Front R Outputs Sorties AusgangsanschlüsseRotel RSX-972 Inputs Entrées EingangsanschlüsseAmplifier Verstärker Zone 2 IR Antenna Antenne Anschließen der Antennen System Status Contents Key Features PlacementUnpacking Basic Controls EXT Input ControlsTuner Controls Preset Button Numeric Buttons Station PresetsMemory Button Direct ButtonPTY Button Display ButtonTP Button TA ButtonVideo Connections Video Source InputsCD Inputs Tape Inputs and OutputsVideo Antenna Connections Zone 2 Power On/Off Operation FM Wire AntennaAC Input 12V Trigger ConnectionsControlling Zone 2 from the Remote Location Controlling Zone 2 from the Main Room Zone ButtonZone 2 Audio Outputs Zone REM in JackIR OUT Jacks ConfigurationNavigation Buttons System Status MenuInput Menu Speaker Setup MenuCenter Speaker small/large/none Surround Speakers small/largeDelay Setup Menu Subwoofer Level MenuTest Tone Menu Reset Menu Zone 2 Setup MenuOther Options Menu Specifications Sommaire Les commandes des entréesPour démarrer Au sujet de RotelCommande de volume Capteur de télécommandeProgrammation de la RR-969 Mise en veille StandbyTouches de sélection de source en lecture Les commandes du son SurroundTouche d’enregistrement REC Touche Zone Touche d’entrée 5.1 CH 5+1 canaux Touche d’entrée EXTDynamic Range Commandes du tunerMemory BandPreset Vidéo Composite et S-Vidéo Sauf ex Informations concernant les branchements VidéoTape Video 1-3 sorties Vidéo composite Video 1-3 sorties AudioVideo 1-3 sorties Vidéo S-vidéo Entrées numériques DigitalExternal REM. Pour activer ou désactiver la Zone Mise en/hors service fonctionnement ZoneSorties audio Zone Contrôle de la Zone 2 à partir de la télécommandePrise Zone REM Prises IR OUTTouches de navigation Touches repérées DOWN/-UP basTouches repérées +/- Modifient le Menu des entrées Input Menu principal Main MenuMenu de réglage des enceintes acoustiques Speaker Setup Menu de réglage du temps de retard Delay Setup Menu du générateur de signal de test Test ToneMenu de réglage du caisson de grave Subwoofer Level Menu de remise à zéro des réglages Reset Menus des autres optionsOther Options Spécifications Zone 2 SetupAuf die Abbildungen des RSX-972. Die grau Die grau markierten Zahlen beziehen sichWesentliche Ausstattungsmerkmale Die Firma RotelAuspacken des Gerätes Einige VorsichtsmaßnahmenGrundfunktionen Eingangswahl STEREO-Taste PROLOGIC-TasteDSP-Taste 2CH-TasteZifferntasten DIRECT-Taste PRESET-TasteMONO-Taste PTY-TasteTP-Taste ÜberblickTA-Taste Informationen zu den VideoanschlüssenAnschließen der Audioquellen Video 1 3 Audioausgänge Anschließen einer DigitalquelleVideo 1 3 Composite-Video-Ausgänge Video 1 Video-AusgängeAntennenanschlüsse Zone 2-Betrieb Bedienung von Zone 2 vom Haupthörraum aus ZONE-Taste Steuerung von Zone 2 über die FernbedienungZone 2-Audioausgänge Zone REM IN-Buchse Volume Lautstaerke die aktuelleIR OUT-Buchsen Diese Tasten führen Sie durch die MenüsEingangs Setup MAIN-Menü HauptmenuINPUT-Menü Lautsprecher Typen Speaker SETUP-MenüFrontlautsprecher small/large Centerlautsprecher small/largeVerzoegerungs Zeiten Delay SETUP-MenüSubwoofer LEVEL-Menü SUB Pegel Test TONE-MenüRESET-Menü Ruecksetzen AUF Grundeinstellung Other OPTIONS-MenüWeitere Einstellungen Zone Einstellungen Technische DatenPage Page Rotel of America Rotel EuropeRotel Deutschland

RSX-972 specifications

The Rotel RSX-972 is a high-performance home theater receiver that combines sophisticated audio processing with versatile connectivity options, making it an ideal choice for audiophiles and home theater enthusiasts alike. Known for its robust build quality and impeccable sound reproduction, the RSX-972 exemplifies Rotel's commitment to delivering premium audio experiences.

One of the hallmark features of the RSX-972 is its exceptional power amplification. The unit is outfitted with a high-output, multi-channel amplifier that provides 100 watts per channel across all five channels. This ensures that your audio sources, whether they be movies, music, or games, are delivered with clarity and impact, allowing users to enjoy an immersive soundstage. Additionally, the receiver employs Rotel's proprietary Distributed Mode Radiators (DMR) technology that enhances bass response and overall frequency performance, further enriching the audio experience.

In terms of connectivity, the RSX-972 is equipped with a plethora of input and output options to accommodate various audio and video components. It features multiple digital audio inputs, including coaxial and optical connections, as well as traditional analog inputs. The inclusion of a built-in AM/FM tuner also allows users to access radio broadcasts with ease.

The RSX-972 supports multiple surround sound formats, including Dolby Digital, DTS, and other advanced audio technologies. This allows the receiver to decode high-definition soundtracks seamlessly, ensuring a cinema-like experience at home. Moreover, the integrated video upscaling capability enhances standard-definition video sources, providing improved clarity and resolution for a more engaging visual experience.

Another standout aspect of the RSX-972 is its user-friendly interface. The receiver comes with an intuitive remote control and an on-screen display that simplifies navigation and setup. Users can easily switch between sources, adjust audio settings, and configure speaker settings without hassle.

The build quality of the Rotel RSX-972 is exceptional, featuring a sleek aluminum front panel and high-grade components designed to minimize distortion and improve overall sound fidelity. Whether you're watching action-packed films or listening to your favorite music, the RSX-972 stands out as a solid performer, delivering a versatile and high-fidelity audio experience that is hard to surpass in its class. With these features, it remains a strong choice for anyone looking to enhance their home entertainment system.
Top Page Image Contents