Shindaiwa T2510X/EVC, T2510/EVC, 89300 Long Term Storage, 0XIÁHUDQGVSDUNDUUHVWHU Dlqwhqdqfh

Page 18

Maintenance (continued)

0XIÁHUDQGVSDUNDUUHVWHU DLQWHQDQFH

If the engine becomes sluggish and low on power, check and clean the spark arrester screen.

WARNING!

Never operate the unit with a

GDPDJHRUPLVVLQJPXIÀHURUVSDUN arrester! Operating with a missing or GDPDJHGVSDUNDUUHVWHULVD¿UHKD]DUG and could also damage your hearing.

1.With a 3 mm hex wrench remove the engine cover screws and the engine cover.

2.With a 4 mm hex wrench, remove the 3 muffler bolts and the muffler.

3.With a small flat bladed screwdriver remove the 2 screws holding the spark arrester screen and cover to the muffler.

4.Remove the screen and clean it with a stiff bristle brush.

5.Inspect the cylinder exhaust port for any carbon buildup.

6.Reassemble the spark arrester, muffler and engine cover in the reverse order of disassembly.

IMPORTANT!

If you note excessive carbon buildup, con- sult with an authorized servicing dealer.

Engine Cover

Engine Cover

Screws

0XIÀHU

0XIÀHU*DVNHW

0XIÀHU%ROWV

Spark Arrester Screen

Spark Arrester Cover

Cover Screws

Long Term Storage

Whenever the unit will not be used for 30 days or longer, use the following proce- dures to prepare it for storage:

ŶClean external parts thoroughly.

ŶDrain all the fuel from the carburetor and the fuel tank.

To do so:

1.Prime the primer bulb until no more fuel is passing through.

2.Start and run the engine until it stops running.

3.Repeat steps 1 and 2 until the engine will no longer start.

CAUTION!

Gasoline stored in the carburetor for extended periods can cause hard start- ing, and could also lead to increased service and maintenance costs.

IMPORTANT!

All stored fuels should be stabilized with a fuel stabilizer such as STA-BIL.

NOTE

Damage caused by stale or contaminated fuel is not covered by the Shindaiwa war- ranty policy.

ŶRemove the spark plug and pour about

7 mL (.25 oz.) of 2-cycle mixing oil into the cylinder through the spark plug hole. Slowly pull the recoil starter 2 or 3 times so oil will evenly coat the interior of the engine. Reinstall the spark plug.

ŶBefore storing the unit, repair or replace any worn or damaged parts.

ŶRemove the air cleaner element from the carburetor and clean it thoroughly with soap and water, let dry and reas- semble the element.

ŶStore the unit in a clean, dust-free area.

18

Image 18
Contents T2510/EVC Trimmer T2510X/EVC Trimmer Contents IntroductionWork Safely SafetySafety Labels Stay AlertProperly Equipped Operator Be Aware of the Working EnvironmentProduct Description T2510XEngine and shaft assembly Cutting attachment shield AssemblyPrior to Assembly Handle and barrier bar X unitSub-Shield When trimmer head is in use Cutting Attachment Shield T, TX unitAdjust throttle lever free play Install trimmer headInstalling Brushcutter Blade Remove the hex wrenchExamples of 501 mixing quantities Mixing fuelFilling the fuel tank Minimize the Risk of FireWhen the Engine Starts Starting the EngineDepress and hold the throttle lock button Stopping the Engine Adjusting Engine IdleIdle Speed Adjustment Checking Unit ConditionOperation Brushcutter Handlebar Using a BladeBlade Thrust Brushcutter harnessMaintenance Remove and clean or replace the spark plug Hour maintenance10/15-Hour maintenance Gearcase lubricationMaintenance after first 139-hours 139/150-Hour MaintenanceValve Adjustment Remove and replace the fuel filter ElementLong Term Storage 0XIÁHUDQGVSDUNDUUHVWHU DlqwhqdqfhBlade Sharpening Shindaiwa Tornado BladeMultiple-tooth Circular Blade What To Check Troubleshooting GuideEngine does not Start RemedyIs the engine overheating? LOW PowerPossible Cause Engine is knockingAdditional Problems What To Check Possible Cause RemedyEmission System Warranty Statement NOTAs RemarquesPodadora T2510 Podadora T2510X Declaraciones De Seguridad IntroducciónContenido Etiquetas de seguridadMantengase Alerta SeguridadTrabaje con cuidado Etiquetas de seguridadSeguridad continuación El operario debidamente equipadoSP4 Alteraciones no autorizadas a nin Descripción del ProductoCon seguridad Guna de éstas máquinas ni a susMango y barra protectora unidades TX EnsamblajeAntes de Ensamblar Mantenga el mango de apoyo frente a la marca de la etiquetaProtector Secundario cuando el Protector del accesorio de corteSP7 Instalación del cabezal de corte Ensamblaje continuacionAjuste la holgura del acelerador SP8Instalación de la cuchilla desmalezadora Ejemplos de cantidades de mezcla a proporción de Mezcla de CombustibleLlenando el Tanque de Combustible Disminuya el riesgo de incendiosArranque del motor Al arrancar el motorDeslice el interruptor de ignición a la Posición O motor ApagadoCorte de Césped Máquinas Equipadas con Cabezal de Corte OperaciónCorrea de Hombro BordesOperación continuación Mantenimiento Mantenimiento cada 50 horas Mantenimiento continuaciónMantenimiento cada 10 horas Más frecuentemente en condiciones rigurosasRetire y reemplace el elemento del filtro Mantenimiento Cada 139/150 HorasAjuste de válvulas Un ajuste incorrecto de las válvuRetire la malla y limpie con un cepillo de cerdas gruesas Mantenimiento de la silenciadorAlmacenamiento de Largo Plazo Repita los pasos 1 y 2 hasta que el motor ya no arranqueDisco Shindaiwa Tornado Discos de dientes múltiplesQué revisar Guía DiagnósticoEL Motor no Arranca Posible causaLimpiar, reparar o sustituir en caso necesario Baja Potencia¿Se sobrecalienta el motor? El motor golpeaGuía Diagnóstico continuación Cobertura de la Garantía del Fabricante Esta garantía es administrada porSus Derechos y Obligaciones de Garantía Que Está Cubierto Por Esta GarantíaTualatin, Oregon 97062 USA 11, Ozuka-Nishi COUPE-BORDURE T2510/EVC T2510X/EVC Table des matières Mises en gardeDemeurer alerte SécuritéSécurité au travail Étiquettes de sécuritéSécurité suite Équipement complet de l’utilisateurNomenclature Caractéristiques techniquesPoignée y Barre de sécurité X appareil AssemblageAvant l’assemblage FR6PÁHFWHXULQIpULHXUlorsque la tête Assemblage suitePÁHFWHXU FR7Ôter la clé hexagonale Installer la tête de coupe Installer la tête de coupeRéglage du jeu du levier d’accélération FR8Installation de la lame de débroussailleuse Exemples de quantités de mélange de carburant à Mélange de carburantRemplissage du réservoir à carburant Réduire les risques d’incendieDémarrage du moteur Lorsque le moteur démarreRéglage du ralenti du moteur Démarrage du moteur suiteArrêt du moteur Contrôle de l’état de l’appareilFonctionnement Fonctionnement suite Entretien Entretien aux 10 à 15 heures Entretien suiteEntretien aux 10 heures Entretien aux 50 heuresEntretien aux 139 heures Remplacement du filtre à carburantEntretien toutes les 50 heures suite Réglage du jeu des soupapesRemisage à long terme Entretien du silencieuxAffûtage de la lame Lame Shindaiwa TornadoLame circulaire à plusieurs dents LE Moteur NE Démarre PAS SolutionGuide de dépannage Points à contrôlerLe moteur surchauffe-t-il ? Guide de dépannage suitePuissance Insuffisante Le moteur cognePoints à contrôler Cause probable Solution Autres ProblèmesCouverture de la garantie des fabricants La présente garantie est administrée parVos droits et obligations en vertu de la garantie Couverture de la garantie