Shindaiwa 89300, T2510/EVC, T2510X/EVC manual Operation

Page 13

Operation

Shoulder Strap

WARNING!

Always wear a shoulder strap when operating this unit with a blade. A shoulder strap is also recommened when using trimmer line.

1.Hook the strap hook to the hanger on the outer tube.

2.Wear the shoulder strap so that the hook stays at your right hand side.

 

 

 

IMPORTANT!

TX unit

 

 

Adjust the shoulder strap or harness so the

 

Harness

 

shoulder pad rests comfortably on the off-side

 

 

shoulder and the cutting path of the cutting

 

 

 

 

 

 

attachment is parallel to the ground. Make sure

 

 

 

all hooks and adjustment devices are secure.

 

 

 

 

3.Adjust the length of the shoulder strap so that you can hold and operate the machine comfortably.

Cutting grass with a trimmer head

Your Shindaiwa unit may be equipped with one of several Shindaiwa trimmer head mod- els, each with features for specific applica- tions and/or operational requirements.

NOTE:

For proper operation, always refer to the instructions accompanying the trimmer head being used.

Trimmer head styles:

Semi-automatic. Trimmer line is indexed when the operator taps the trimmer head on the ground during operation.

Manual. The operator indexes line manu- ally with the grass trimmer stopped.

Fixed. The operator must stop the unit and add new lengths of trimmer line manually.

Flail. This device, designed for clearing weeds and light brush, features three nylon blades attached to the head by pivots.

Edging

Tilt the handle about 100° to the left (from horizontal) and move forward, holding the trimmer or brushcutter vertically as shown.

NOTE:

Additional hardware may be required to mount the Fixed Line or the Flail type trimmer heads.

Engine Operating Speeds

Operate at full throttle while cutting grass.

CAUTION!

Operation at low rpm can lead to pre- mature clutch failure.

Trimming and Mowing Grass

Hold the grass trimmer so the trimmer head is angled slightly into the area to be cut. To ensure maximum trimmer-line service life, cut only with the tip of the trimmer line. Cut grass by swinging the unit's trimmer head from left to right. Keep the trimmer head horizontal.

Tilt the handle about

100° to the left

CAUTION!

ŶDo not push the rotating line into trees, wire fences or any material that could tangle or break line ends.

ŶOperation of trimmer without a cutting attachment shield and using exces- sive line length can lead to premature clutch failure.

ŶOperation at low rpm can lead to premature clutch failure.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents T2510/EVC Trimmer T2510X/EVC Trimmer Introduction ContentsSafety Labels SafetyWork Safely Stay AlertBe Aware of the Working Environment Properly Equipped OperatorT2510X Product DescriptionPrior to Assembly AssemblyEngine and shaft assembly Cutting attachment shield Handle and barrier bar X unitCutting Attachment Shield T, TX unit Sub-Shield When trimmer head is in useInstall trimmer head Adjust throttle lever free playRemove the hex wrench Installing Brushcutter BladeFilling the fuel tank Mixing fuelExamples of 501 mixing quantities Minimize the Risk of FireStarting the Engine When the Engine StartsDepress and hold the throttle lock button Idle Speed Adjustment Adjusting Engine IdleStopping the Engine Checking Unit ConditionOperation Blade Thrust Using a BladeBrushcutter Handlebar Brushcutter harnessMaintenance 10/15-Hour maintenance Hour maintenanceRemove and clean or replace the spark plug Gearcase lubricationValve Adjustment 139/150-Hour MaintenanceMaintenance after first 139-hours Remove and replace the fuel filter Element0XIÁHUDQGVSDUNDUUHVWHU Dlqwhqdqfh Long Term StorageShindaiwa Tornado Blade Blade SharpeningMultiple-tooth Circular Blade Engine does not Start Troubleshooting GuideWhat To Check RemedyPossible Cause LOW PowerIs the engine overheating? Engine is knockingWhat To Check Possible Cause Remedy Additional ProblemsEmission System Warranty Statement Remarques NOTAsPodadora T2510 Podadora T2510X Contenido IntroducciónDeclaraciones De Seguridad Etiquetas de seguridadTrabaje con cuidado SeguridadMantengase Alerta Etiquetas de seguridadEl operario debidamente equipado Seguridad continuaciónSP4 Con seguridad Descripción del ProductoAlteraciones no autorizadas a nin Guna de éstas máquinas ni a susAntes de Ensamblar EnsamblajeMango y barra protectora unidades TX Mantenga el mango de apoyo frente a la marca de la etiquetaProtector del accesorio de corte Protector Secundario cuando elSP7 Ajuste la holgura del acelerador Ensamblaje continuacionInstalación del cabezal de corte SP8Instalación de la cuchilla desmalezadora Llenando el Tanque de Combustible Mezcla de CombustibleEjemplos de cantidades de mezcla a proporción de Disminuya el riesgo de incendiosAl arrancar el motor Arranque del motorPosición O motor Apagado Deslice el interruptor de ignición a laCorrea de Hombro OperaciónCorte de Césped Máquinas Equipadas con Cabezal de Corte BordesOperación continuación Mantenimiento Mantenimiento cada 10 horas Mantenimiento continuaciónMantenimiento cada 50 horas Más frecuentemente en condiciones rigurosasAjuste de válvulas Mantenimiento Cada 139/150 HorasRetire y reemplace el elemento del filtro Un ajuste incorrecto de las válvuAlmacenamiento de Largo Plazo Mantenimiento de la silenciadorRetire la malla y limpie con un cepillo de cerdas gruesas Repita los pasos 1 y 2 hasta que el motor ya no arranqueDiscos de dientes múltiples Disco Shindaiwa TornadoEL Motor no Arranca Guía DiagnósticoQué revisar Posible causa¿Se sobrecalienta el motor? Baja PotenciaLimpiar, reparar o sustituir en caso necesario El motor golpeaGuía Diagnóstico continuación Sus Derechos y Obligaciones de Garantía Esta garantía es administrada porCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaTualatin, Oregon 97062 USA 11, Ozuka-Nishi COUPE-BORDURE T2510/EVC T2510X/EVC Mises en garde Table des matièresSécurité au travail SécuritéDemeurer alerte Étiquettes de sécuritéÉquipement complet de l’utilisateur Sécurité suiteCaractéristiques techniques NomenclatureAvant l’assemblage AssemblagePoignée y Barre de sécurité X appareil FR6PÁHFWHXU Assemblage suitePÁHFWHXULQIpULHXUlorsque la tête FR7Réglage du jeu du levier d’accélération Installer la tête de coupe Installer la tête de coupeÔter la clé hexagonale FR8Installation de la lame de débroussailleuse Remplissage du réservoir à carburant Mélange de carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieLorsque le moteur démarre Démarrage du moteurArrêt du moteur Démarrage du moteur suiteRéglage du ralenti du moteur Contrôle de l’état de l’appareilFonctionnement Fonctionnement suite Entretien Entretien aux 10 heures Entretien suiteEntretien aux 10 à 15 heures Entretien aux 50 heuresEntretien toutes les 50 heures suite Remplacement du filtre à carburantEntretien aux 139 heures Réglage du jeu des soupapesEntretien du silencieux Remisage à long termeLame Shindaiwa Tornado Affûtage de la lameLame circulaire à plusieurs dents Guide de dépannage SolutionLE Moteur NE Démarre PAS Points à contrôlerPuissance Insuffisante Guide de dépannage suiteLe moteur surchauffe-t-il ? Le moteur cogneAutres Problèmes Points à contrôler Cause probable SolutionVos droits et obligations en vertu de la garantie La présente garantie est administrée parCouverture de la garantie des fabricants Couverture de la garantie
Top Page Image Contents