Shindaiwa 89310, AH2510/EVC Stopping the Engine, Adjusting Engine Idle, Checking Unit Condition

Page 10

Starting the Engine (continued)

Starting A Flooded Engine

1.Disconnect the spark plug lead and use the spark plug wrench to remove the spark plug (turn counter clockwise to remove).

2.Slide the ignition switch to the “O” (STOP) position.

ŶIf the spark plug is fouled or soaked with fuel, clean the plug as necessary.

3.Open the choke and fully depress the throttle lever with your left hand, then pull the starter handle rapidly with your right hand to clear excess fuel from the combustion chamber.

4.Replace the spark plug and tighten it firmly with the spark plug wrench. If a torque wrench is available, torque the spark plug to the values recommended in the “Specifications” section.

5.Repeat the starting procedure for a warm engine.

6.If the engine still fails to start, refer to the troubleshooting section near the end of this manual.

Stopping the Engine

Idle the engine briefly before stopping (about 2 minutes), then slide the ignition

switch to the “O” (Engine OFF) position.

OFF

Slide ignition to OFF

Adjusting Engine Idle

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

WARNING!

The cutting attachment must NEVER rotate at engine idle! If the idle speed cannot be adjusted by the procedure described here, return the unit to your Shindaiwa dealer for inspection.

Checking Unit Condition

Idle Speed Adjustment

1.Place the unit on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.

2.If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise.

3.If a tachometer is available, adjust idle. Check Specifications page for correct idle speed

NOTE

Carburetor fuel mixture adjustments are preset at factory and cannot be serviced LQWKH¿HOG

Idle Adjusting

Screw

NEVER operate the unit with the cut- ting attachment shield or other protec- tive devices removed!

Use only authorized Shindaiwa parts and accessories with your Shindaiwa trimmer. Do not make modifications to this unit with- out written approval from Shindaiwa, Inc.

ALWAYS make sure the cutting attach- ment is properly installed and firmly tightened before operation.

NEVER use a cracked or warped cutting attachment: replace it with a serviceable one.

ALWAYS make sure the cutting attach- ment fits properly into the appropriate attachment holder. If a properly installed attachment vibrates, replace the attach- ment with new one and re-check.

ALWAYS stop the engine immediately and check for damage if you strike a foreign object or if the unit becomes tangled. Do not operate with broken or damaged equipment.

NEVER allow the engine to run at high RPM without a load. Doing so could dam- age the engine.

NEVER operate a unit with worn or dam- aged fasteners or attachment holders.

WARNING!

A cutting attachment shield or other protective device is no guarantee of protection against ricochet. YOU MUST ALWAYS GUARD AGAINST FLYING DEBRIS!

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Articulated Hedge Trimmer English Español .... SP1 Français ... FR1Safety and operation labels ContentsIntroduction Operating Precautions SafetyArticulated Safety Equipment and Labels Operator SafetyING Product DescriptioLife, and safer o Alter this machine mponentsConnect the Outer Tube to the Powerhead AssemblyPrior To Assembly Connect the Throttle CableAdjusting for Storage or Transportation Adjusting the Hedge Trimmer Cutter AssemblyCutter Assembly Positions Throttle lever free playExamples of 501 mixing quantities Mixing fuelFilling the fuel tank Minimize the Risk of FireStarting the Engine When the Engine StartsDepress and hold the throttle lock button Stopping the Engine Adjusting Engine IdleIdle Speed Adjustment Checking Unit ConditionCutting Sequence Using the Hedge Trimmer PreparationsOperation Cutting TechniquesMaintenance Remove and clean or replace the spark plug Hour maintenance10/15-Hour maintenance Direct the air stream at the inside face of the filter onlyRemove and replace the fuel filter element XHO¿OWHUPDLQWHQDQFHCutter blade adjustment 139/150-Hour MaintenanceValve Adjustment Maintenance after first 139-hoursLong Term Storage 0XIÁHUDQGVSDUNDUUHVWHU DlqwhqdqfhWhat To Check Troubleshooting GuideEngine does not Start RemedyIs the engine overheating? LOW PowerPossible Cause Engine is knockingAdditional Problems What To Check Possible Cause RemedyEmission System Warranty Statement NOTAs Remarques Remarques 731-3167, Japan Cortasetos Articulado AH2510/EVC ¡ADVERTENCIADeclaraciones De Seguridad IntroducciónEtiquetas de seguridad Seguridad Precauciones de utilizaciónSeguridad continuación Descripción del Pr BloqueoConecte el tubo exterior de bloque de motor EnsamblarAntes de Ensamblar Conexión del cable del aceleradorAjuste del conjunto de la cuchilla del cortasetos Ensamblar continuaciónAjuste la holgura del acelerador Precaución Mezcla de CombustibleLlenando el Tanque de Combustible AdvertenciaArranque del motor Al arrancar el motorDeslice el interruptor de ignición a la Posición O motor ApagadoUsando la cortasetos AplicacionesTécnicas de corte Mantenimiento Mantenimiento cada 10 horas Mantenimiento continuaciónMantenimiento cada 10 o 15 horas Retire y reemplace el elemento del filtro Mantenimiento cada 50 horasCon más frecuencia en condiciones de polvo o suciedad Afloje el perno de fijación de la caja de engranajesAjuste de válvulas Mantenimiento Cada 139/150 HorasAjuste de las cuchillas de corte Retire la malla y limpie con un cepillo de cerdas gruesas Almacenamiento de Largo PlazoMantenimiento de la silenciador Repita los pasos 1 y 2 hasta que el motor ya no arranqueQué revisar Guía DiagnósticoEL Motor no Arranca Posible causaEl motor golpea Baja Potencia¿Se sobrecalienta el motor? La parte superiore La tapa de la valvula está goteandoGuía Diagnóstico continuación Cobertura de la Garantía del Fabricante Esta garantía es administrada porSus Derechos y Obligaciones de Garantía Que Está Cubierto Por Esta GarantíaSP21 SP22 SP23 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi TAILLE-HAIE Articulé AH2510/EVC AvertissementMise EN Garde Table des matièresMises en garde RemarqueSécurité Consignes d’utilisationSécurité d’opérateur Sécurité suiteÉtiquettes et dispositifs de sécurité Er immédiatement toute étiquette manquanteUne utilisation plus sûre NomenclaatureCaractéristiques techniques EmentMontage de la tête motorisée AssemblageAvant l’assemblage Brancher et réglage du câble d’accélérationAssemblage suite Réglage de l’accessoire de coupe du taille-haiePositions de l’accessoire de coupe Réglage de la course libre du levier d’accélérationExemples de quantités de mélange de carburant à Mélange de carburantRemplissage du réservoir à carburant Réduire les risques d’incendieDémarrage du moteur Lorsque le moteur démarreRéglage du ralenti du moteur Démarrage du moteur suiteArrêt du moteur Contrôle de l’état de l’appareilOrdre de coupe FonctionnementUtilisation du taille-haie Préparations Techniques de coupeEntretien Entretien aux 10 heures Entretien suiteEntretien aux 10 à 15 heures Plus souvent dans des conditions poussiéreuses ou sales Remplacement du filtre à carburantEntretien aux 50 heures Santes du système d’alimentation en carEntretien aux 139 heures Réglage de la lame de l’accessoire de coupeRéglage du jeu des soupapes Remisage à long terme Entretien du silencieuxLE Moteur NE Démarre PAS SolutionGuide de dépannage Points à contrôlerLe moteur surchauffe-t-il ? Guide de dépannage suitePuissance Insuffisante Le moteur cognePoints à contrôler Cause probable Solution Autres ProblèmesCouverture de la garantie des fabricants La présente garantie est administrée parVos droits et obligations en vertu de la garantie Couverture de la garantieFR21 FR22 FR23

89310, AH2510, AH2510/EVC specifications

The Shindaiwa AH2510/EVC, AH2510, and 89310 models represent a perfect blend of efficiency, versatility, and durability in the world of handheld outdoor power equipment. These tools are designed for both professional landscapers and avid gardeners, offering cutting-edge features and innovative technologies that make yard maintenance tasks easier and more effective.

One of the standout features of the Shindaiwa AH2510 is its powerful engine. Equipped with a robust two-stroke engine, the AH2510 delivers impressive performance while ensuring high fuel efficiency. This not only allows users to complete their tasks swiftly but also minimizes operational costs. The engine's design reduces emissions, meeting stringent environmental regulations and ensuring a cleaner working environment.

Another highlight of the Shindaiwa AH2510/EVC is its ergonomic design. The equipment comes with a padded handle for comfortable grip and ease of use, reducing operator fatigue during extended use. The lightweight construction of the tools further contributes to their maneuverability, making them ideal for both large areas and intricate landscaping work. Users will appreciate the balance and control afforded by the design, which enables them to navigate varied terrains effortlessly.

Technology is at the forefront of the Shindaiwa AH2510 series. Features like the Easy Start System significantly reduce the effort required to start the machine, allowing users to get to work with minimal downtime. Additionally, the advanced vibration-damping technology enhances user comfort, allowing for longer periods of use without the strain associated with traditional equipment.

Durability is a hallmark of Shindaiwa products. The AH2510 models are constructed with high-quality materials that withstand the rigors of everyday use, ensuring a long lifespan. Furthermore, the commercial-grade components mean that these tools can handle demanding tasks without compromising performance.

Versatility is another key characteristic of the AH2510 series. This range of tools can be easily adapted for various applications, making them suitable for trimming, pruning, and more. Users can switch attachments seamlessly, transforming their equipment to meet the challenges of different jobs.

In summary, the Shindaiwa AH2510/EVC, AH2510, and 89310 models offer a compelling combination of power, comfort, and adaptability. With their robust engineering, user-friendly features, and environmental consciousness, these tools stand out in the competitive market of outdoor power equipment, catering to the needs of professionals and homeowners alike.
Top Page Image Contents