Shindaiwa AH2510/EVC, 89310 manual Maintenance

Page 12

Maintenance

General maintenancel

IMPORTANT!

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PER- FORMED BY ANY REPAIR ESTABLISH- MENT OR INDIVIDUAL; HOWEVER, WAR- RANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA INC. THE USE OF PARTS THAT ARE NOT EQUIVA- LENT IN PERFORMANCE AND DURA- BILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM.

NOTE:

Using non-standard replacement parts could invalidate your Shindaiwa warranty.

WARNING!

Before performing any mainte- nance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped.

Disconnect the spark plug wire before performing service or maintenance.

0XIÁHU

This unit must never be operated with a faulty or missing spark arrester or muf- fler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss.

Spark Plug

Keep the spark plug and wire connections tight and clean.

Fasteners

Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight.

WARNING!

Non-standard accessories, cut- ting attachment, or replacement parts may not operate properly with your unit and may cause damage and lead to personal injury.

Air Filter

The C4 engine that powers your Shindaiwa model is a hybrid 4-stroke engine. As a hybrid, the engine is lubricated by oil mixed with the gasoline and air from the carburetor that moves through and around the internal parts of the engine in a similar way that a

2-stroke engine is lubricated. Without the heavy duty 2-stage air filter equipped on all C4 engines, dust and dirt could also move through the engine, decreasing engine life, increasing valve wear and the need for more frequent valve adjustments. To keep your C4 engine strong and reliable, Shindaiwa recommends that you check and service the air filter as instructed in the 10-Hour Mainte- nance section that follows.

Daily maintenance

Prior to each work day, perform the following:

ŶRemove all dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as necessary.

ŶCarefully remove any accumulations of dirt or debris from the muffler and fuel tank. Check cooling air intake area at base of crankcase. Remove all debris. Dirt build-up in these areas can lead to engine overheating, fire, or premature wear.

WARNING!

Always wear gloves when working around the cutter assembly.

ŶLubricate the blades before use and after refueling. Check the cutters for damage or incorrect adjustment.

ŶClean any debris or dirt from the cut- ting attachment.

Cooling

¿QV

Cooling

¿QV

Air

intake

5HPRYHDOOGLUWDQGGHEULVIURPWKHHQJLQHDQGFKHFNWKHFRROLQJ¿QV

Ŷ Check for loose or missing screws or

Ŷ Make sure nuts, bolts, and screws

components. Make sure the cutter

(except carburetor idle speed adjusting

attachment is securely fastened.

screws) are tight.

Ŷ Check the entire unit for leaking fuel

 

or grease.

 

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Articulated Hedge Trimmer English Español .... SP1 Français ... FR1Contents Safety and operation labelsIntroduction Safety Operating PrecautionsArticulated Safety Equipment and Labels Operator SafetyProduct Descriptio Life, and safer oING Alter this machine mponentsAssembly Prior To AssemblyConnect the Outer Tube to the Powerhead Connect the Throttle CableAdjusting the Hedge Trimmer Cutter Assembly Cutter Assembly PositionsAdjusting for Storage or Transportation Throttle lever free playMixing fuel Filling the fuel tankExamples of 501 mixing quantities Minimize the Risk of FireWhen the Engine Starts Starting the EngineDepress and hold the throttle lock button Adjusting Engine Idle Idle Speed AdjustmentStopping the Engine Checking Unit ConditionUsing the Hedge Trimmer Preparations OperationCutting Sequence Cutting TechniquesMaintenance Hour maintenance 10/15-Hour maintenanceRemove and clean or replace the spark plug Direct the air stream at the inside face of the filter onlyRemove and replace the fuel filter element XHO¿OWHUPDLQWHQDQFH139/150-Hour Maintenance Valve AdjustmentCutter blade adjustment Maintenance after first 139-hoursLong Term Storage 0XIÁHUDQGVSDUNDUUHVWHU DlqwhqdqfhTroubleshooting Guide Engine does not StartWhat To Check RemedyLOW Power Possible CauseIs the engine overheating? Engine is knockingAdditional Problems What To Check Possible Cause RemedyEmission System Warranty Statement NOTAs Remarques Remarques 731-3167, Japan Cortasetos Articulado AH2510/EVC ¡ADVERTENCIAIntroducción Declaraciones De SeguridadEtiquetas de seguridad Seguridad Precauciones de utilizaciónSeguridad continuación Descripción del Pr BloqueoEnsamblar Antes de EnsamblarConecte el tubo exterior de bloque de motor Conexión del cable del aceleradorEnsamblar continuación Ajuste del conjunto de la cuchilla del cortasetosAjuste la holgura del acelerador Mezcla de Combustible Llenando el Tanque de CombustiblePrecaución AdvertenciaArranque del motor Al arrancar el motorDeslice el interruptor de ignición a la Posición O motor ApagadoAplicaciones Usando la cortasetosTécnicas de corte Mantenimiento Mantenimiento continuación Mantenimiento cada 10 horasMantenimiento cada 10 o 15 horas Mantenimiento cada 50 horas Con más frecuencia en condiciones de polvo o suciedadRetire y reemplace el elemento del filtro Afloje el perno de fijación de la caja de engranajesMantenimiento Cada 139/150 Horas Ajuste de válvulasAjuste de las cuchillas de corte Almacenamiento de Largo Plazo Mantenimiento de la silenciadorRetire la malla y limpie con un cepillo de cerdas gruesas Repita los pasos 1 y 2 hasta que el motor ya no arranqueGuía Diagnóstico EL Motor no ArrancaQué revisar Posible causaBaja Potencia ¿Se sobrecalienta el motor?El motor golpea La parte superiore La tapa de la valvula está goteandoGuía Diagnóstico continuación Esta garantía es administrada por Sus Derechos y Obligaciones de GarantíaCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaSP21 SP22 SP23 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi TAILLE-HAIE Articulé AH2510/EVC AvertissementTable des matières Mises en gardeMise EN Garde RemarqueSécurité Consignes d’utilisationSécurité suite Étiquettes et dispositifs de sécuritéSécurité d’opérateur Er immédiatement toute étiquette manquanteNomenclaature Caractéristiques techniquesUne utilisation plus sûre EmentAssemblage Avant l’assemblageMontage de la tête motorisée Brancher et réglage du câble d’accélérationRéglage de l’accessoire de coupe du taille-haie Positions de l’accessoire de coupeAssemblage suite Réglage de la course libre du levier d’accélérationMélange de carburant Remplissage du réservoir à carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieDémarrage du moteur Lorsque le moteur démarreDémarrage du moteur suite Arrêt du moteurRéglage du ralenti du moteur Contrôle de l’état de l’appareilFonctionnement Utilisation du taille-haie PréparationsOrdre de coupe Techniques de coupeEntretien Entretien suite Entretien aux 10 heuresEntretien aux 10 à 15 heures Remplacement du filtre à carburant Entretien aux 50 heuresPlus souvent dans des conditions poussiéreuses ou sales Santes du système d’alimentation en carRéglage de la lame de l’accessoire de coupe Entretien aux 139 heuresRéglage du jeu des soupapes Remisage à long terme Entretien du silencieuxSolution Guide de dépannageLE Moteur NE Démarre PAS Points à contrôlerGuide de dépannage suite Puissance InsuffisanteLe moteur surchauffe-t-il ? Le moteur cognePoints à contrôler Cause probable Solution Autres ProblèmesLa présente garantie est administrée par Vos droits et obligations en vertu de la garantieCouverture de la garantie des fabricants Couverture de la garantieFR21 FR22 FR23

89310, AH2510, AH2510/EVC specifications

The Shindaiwa AH2510/EVC, AH2510, and 89310 models represent a perfect blend of efficiency, versatility, and durability in the world of handheld outdoor power equipment. These tools are designed for both professional landscapers and avid gardeners, offering cutting-edge features and innovative technologies that make yard maintenance tasks easier and more effective.

One of the standout features of the Shindaiwa AH2510 is its powerful engine. Equipped with a robust two-stroke engine, the AH2510 delivers impressive performance while ensuring high fuel efficiency. This not only allows users to complete their tasks swiftly but also minimizes operational costs. The engine's design reduces emissions, meeting stringent environmental regulations and ensuring a cleaner working environment.

Another highlight of the Shindaiwa AH2510/EVC is its ergonomic design. The equipment comes with a padded handle for comfortable grip and ease of use, reducing operator fatigue during extended use. The lightweight construction of the tools further contributes to their maneuverability, making them ideal for both large areas and intricate landscaping work. Users will appreciate the balance and control afforded by the design, which enables them to navigate varied terrains effortlessly.

Technology is at the forefront of the Shindaiwa AH2510 series. Features like the Easy Start System significantly reduce the effort required to start the machine, allowing users to get to work with minimal downtime. Additionally, the advanced vibration-damping technology enhances user comfort, allowing for longer periods of use without the strain associated with traditional equipment.

Durability is a hallmark of Shindaiwa products. The AH2510 models are constructed with high-quality materials that withstand the rigors of everyday use, ensuring a long lifespan. Furthermore, the commercial-grade components mean that these tools can handle demanding tasks without compromising performance.

Versatility is another key characteristic of the AH2510 series. This range of tools can be easily adapted for various applications, making them suitable for trimming, pruning, and more. Users can switch attachments seamlessly, transforming their equipment to meet the challenges of different jobs.

In summary, the Shindaiwa AH2510/EVC, AH2510, and 89310 models offer a compelling combination of power, comfort, and adaptability. With their robust engineering, user-friendly features, and environmental consciousness, these tools stand out in the competitive market of outdoor power equipment, catering to the needs of professionals and homeowners alike.
Top Page Image Contents