Shindaiwa DG1000MI manual Use Parts, Ambient Condition, External view

Page 8

■ Altitude

2.2Ambient Condition

Use the equipment under the following ambient condition. The other condition may cause trouble, insufficient output power or deterioration of durability.

3 Use

4 Parts

Ambient Temperature : -15ºC 40ºC

Humidity	:	less than 80%
	:	less than 300m

Power source for construction～–use equipment, such as submersible pump Power source for lighting

Power source for electric tools and home appliances

4.1 External view

	INSPECTION	FUEL FILTER
	DOOR FOR	FUEL FILTER
	DOOR FOR
	GENERATOR	ROPING LUG	RADIATOR
		ROPING LUG	RADIATOR

LIFTING LUG

INSPECTION DOOR FOR ENGINE

PANEL DOOR

ROPING LUG

	OIL FILTER	WATER	COOLANT
	BATTERY	SEPARATOR	DRAIN PLUG
	EXTERNAL
		EXTERNAL
	FUEL INTAKE		FUEL DRAIN PLUG
		FUEL RETURN

RESERVOIR TANK	ROPING LUG
RESERVOIR TANK
OIL FILLER CAP	OIL GAUGE	AIR CLEANER
OIL FILLER CAP
INSPECTION
DOOR FOR
ENGINE
FUEL INTAKE

FUEL TANK

INSPECTION

DOOR FOR

GENERATOR

1-PHASE OUTPUT TERMINAL

1-PHASE

OUTPUT RECEPTACLES

BONNET

GROUNDING

TERMINAL

BATTERY	3-PHASE	EARTH
	OUTPUT
OIL DRAIN PLUG		GROUNDING	OUT TERMINAL
	TERMINAL
		TERMINAL	COVER

- 8 -

Image 8

Contents DG1000MI Introduction Safety Guidelines Suffocation from exhaust fumeElectrical Shock InjuriesInjuries to eyes and skin ExplosionFire Burns Injuries Location of Warning labels Specifications Specification MatrixExternal view Use PartsAmbient Condition Control panel Equipment Monitor DisplayEngine Oil Monitoring Lamp for oil pressure low Injuries Battery Charge Monitoring Lamp charge lamp Water Temperature GaugeGauges Hour Meter built into the TachometerFuel Gauge Generator GaugesAmp Meter Frequency MeterEmergency Stop button Switch Starter SwitchPanel Light / Pilot Lamp Amp Meter Changeover Switch Thermal RelayEarth Leakage Relay Unit Voltage Regulator and Throttle LeverUsing fuel from built-in fuel tank Fuel Line Changeover Valve 3-way valve＜＞ Transport and Installation TransportationLifting Equipment TransportationSelecting Cable InstallationConnection Electrical damages For 1-Phase Load1 Connecting CableLoad Connection Terminal Plate 3-Phase For 3-Phase Load For 1-Phase Load2 2 1-Phase Output Terminals & ReceptaclesEarth Leakage Relay and Grounding Grounding WorkOperation Check Electrical Shock Initialization and pre-check Earth leakage breaker relay has activatedElectrical Shock Injuries Fire BurnsEngine Oil Capacity Checking Engine OilSelecting proper engine oil Checking Coolant reservoir tank / Adding coolant Checking Coolant/waterChecking Radiator / Adding water Tension Checking Fan BeltCoolant Capacity Checking Fuel ConditionChecking Battery Checking Fuel, Engine Oil, and Water leakageReplacing the battery Operation Initializing / preparationFrequency Adjust Screw 200/400 Voltage Changeover Dual Voltage System Damages to the propertyRefer to 7-2. Connecting cable During operationStopping the Generator Protection FeaturesFeature List Connecting to External Fuel Tank During Operation sectionMaintenance Engine Side Generator side10.1 Oil Change Replace, refer to 8-1 Checking Engine OilCleaning / Changing Air Filter Element Cleaning / Changing Fuel Filter Draining Water from Water SeparatorClean gauze filter in water separator Clean gauze filter in engine feed pumpIsuzu Part No 8970631550 Draining Water from Fuel Tank Storage Procedures Long-term StorageStacking Troubleshooting Ask our distributor to repair Page Generator Wiring Diagram Engine Wiring Diagram