Shindaiwa C242/EVC, 89302 Stopping the Engine, Adjusting Engine Idle, Checking Unit Condition

Page 11

Starting the Engine (continued)

Starting A Flooded Engine

1.Disconnect the spark plug lead and use the spark plug wrench to remove the spark plug (turn counter clockwise to remove).

2.Slide the ignition switch to the “O” (STOP) position.

ŶIf the spark plug is fouled or soaked with fuel, clean the plug as necessary.

3.Open the choke and fully depress the throttle lever with your left hand, then pull the starter handle rapidly with your right hand to clear excess fuel from the combustion chamber.

4.Replace the spark plug and tighten it firmly with the spark plug wrench. If a torque wrench is available, torque the spark plug to the values recommended in the “Specifications” section.

5.Repeat the starting procedure for a warm engine.

6.If the engine still fails to start, refer to the troubleshooting section near the end of this manual.

Stopping the Engine

1.

Idle the engine briefly before stopping

Ignition

 

(about 2 minutes).

switch

2.

Slide the ignition switch to the “O”

OFF

 

 

(Engine OFF) position.

 

Adjusting Engine Idle

IMPORTANT

When the unit is turned off make sure the cutting attachment has stopped before the unit is set down.

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

WARNING!

The cutting attachment must NEVER rotate at engine idle! If the idle speed cannot be adjusted by the procedure described here, return the trimmer to your Shindaiwa dealer for inspection.

Idle Speed Adjustment

1.Place the unit on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.

2.If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise.

3.If a tachometer is available, adjust idle. Check Specifications page for correct idle speed

NOTE

Carburetor fuel mixture adjustments are preset at factory and cannot be serviced LQWKH¿HOG

Idle

adjustment

screw

Adjusting

engine idle

Checking Unit Condition

NEVER operate the unit with the cut- ting attachment shield or other protec- tive devices removed!

Use only authorized Shindaiwa parts and accessories with your Shindaiwa trimmer. Do not make modifications to this unit with- out written approval from Shindaiwa, Inc.

ALWAYS make sure the cutting attach- ment is properly installed and firmly tightened before operation.

NEVER use a cracked or warped cutting attachment: replace it with a serviceable one.

ALWAYS make sure the cutting attach- ment fits properly into the appropriate attachment holder. If a properly installed attachment vibrates, replace the attach- ment with new one and re-check.

ALWAYS stop the engine immediately and check for damage if you strike a foreign object or if the unit becomes tangled. Do not operate with broken or damaged equipment.

NEVER allow the engine to run at high RPM without a load. Doing so could dam- age the engine.

NEVER operate a unit with worn or dam- aged fasteners or attachment holders.

WARNING!

A cutting attachment shield or other protective device is no guarantee of protection against ricochet. YOU MUST ALWAYS GUARD AGAINST FLYING DEBRIS!

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents English BrushcutterIntroduction ContentsStay Alert SafetySafety Labels Work SafelyBe Aware of the Working Environment Properly Equipped OperatorThese units or their components Product DescriptionDo not make unauthorized Install the handlebar AssemblyHandlebar Prior to Assembly Adjust throttle lever free playCutting Attachment Shield Sub-Shield when trimmer head is in useInstalling a Trimmer Head Remove the hex wrench Installing Brushcutter BladeInstall blade holder B on the output shaft Minimize the Risk of Fire Mixing fuelFilling the fuel tank Examples of 501 mixing quantitiesStarting the Engine When the Engine StartsChecking Unit Condition Adjusting Engine IdleIdle Speed Adjustment Stopping the EngineOperation Brushcutter Handlebar Using a bladeBrushcutter Shoulder Strap Blade ThrustMaintenance Gearcase lubrication Hour maintenance10/15 hour maintenance Perform more frequently in dusty or Dirty conditionsRemove and replace the fuel filter element Every 135 hours of operation, remove and clean the mufflerMultiple-tooth Circular Blade Long Term StorageBlade Sharpening Shindaiwa Tornado BladePossible Cause Troubleshooting GuideEngine does not Start What To CheckWhat To Check Possible Cause Remedy LOW PowerAdditional Problems Emission System Warranty Statement NOTAs Remarques 731-3167, Japan Desmalezadora Etiquetas de seguridad IntroducciónContenido Declaraciones De SeguridadEtiquetas de seguridad SeguridadTrabaje con cuidado Mantengase AlertaMáquina descalzo Seguridad continuaciónEl operario debidamente equipado Esté alerta del area de trabajoC242 Descripción del ProductoAjuste la holgura del acelerador EnsamblajeMango tipo bicicleta Antes de Ensamblar Instalación del Cabezal de Nylon Ensamblaje continuacionProtector del accesorio de corte Protector Secundario cuando elInstalación de la cuchilla desmalezadora Disminuya el riesgo de incendios Mezcla de CombustibleLlenando el Tanque de Combustible Ejemplos de cantidades de mezcla a proporción deAl arrancar el motor Arranque del motor9HULÀTXHODFRQGLFLyQGHODXQLGDG Arranque del motor continuaciónApgado del motor Ajuste velocidad mínima del motorBordes OperaciónCorrea de Hombro Corte de Césped Máquinas Equipadas con Cabezal de CorteOperación continuación Mantenimiento Mantenimiento Cada 50 Horas Mantenimiento continuaciónMantenimiento Cada 10 Horas Mantenimiento Cada 10/15 HorasRetire el capuchón de la bujía Mantenimiento del silenciadorUse aceite con estabilizador de combustible Almacenamiento de Largo PlazoDisco Shindaiwa Tornado Discos de dientes múltiplesPosible causa Guia DiagnosticoEL Motor no Arranca Qué revisarDepósitos de carbonilla en el pistón o el silenciador Guia Diagnostico continuaciónBaja Potencia ¿Se sobrecalienta el motor?Otros Problemas Que Está Cubierto Por Esta Garantía Esta garantía es administrada porSus Derechos y Obligaciones de Garantía Cobertura de la Garantía del FabricanteSP22 SP23 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi Débroussailleuse Mises en garde Table des matièresÉtiquettes de sécurité SécuritéSécurité au travail Demeurer alerteTenir compte de l’environnement de travail Sécurité suiteÉquipement complet de l’utilisateur Ne jamais effectuer des NomenclatureCaractéristiques techniques Réglage du jeu de la gâchette d’accélération AssemblageAvant l’assemblage GuidonMontage de la tête de coupe Assemblage suitePÁHFWHXU De l’arbre du carter renvoi d’angle Installer le support de lame B sur l’ar- bre de sortie1HSDV¿HUGHODPHjXQ Bre de sortie du carter renvoi d’angleRéduire les risques d’incendie Mélange de carburantRemplissage du réservoir à carburant Exemples de quantités de mélange de carburant àLorsque le moteur démarre Démarrage du moteurContrôle de l’état de l’appareil Démarrage du moteur suiteArrêt du moteur Réglage du ralenti du moteurFonctionnement Fonctionnement suite Entretien Enlever et nettoyer la bougie Entretien suiteEntretien toutes les 10 heures Entretien toutes les 10 15 heuresEnlever le capuchon de la bougie Entretien toutes les 50 heuresEntretien du pare-étincelles Enlever et remplacer l’élément du filtreLame circulaire à plusieurs dents Remisage à long termeAffûtage de la lame Lame Shindaiwa TornadoPoints à contrôler SolutionGuide de dépannage LE Moteur NE Démarre PASLe moteur cogne Guide de dépannage suitePuissance Insuffisante Le moteur surchauffe-t-il ?Autres Problèmes Couverture de la garantie La présente garantie est administrée parVos droits et obligations en vertu de la garantie Couverture de la garantie des fabricantsFR22 FR23

C242/EVC, 89302 specifications

The Shindaiwa 89302 C242/EVC is a powerful and efficient engine specifically designed for professional landscaping and outdoor maintenance. Renowned for its durability and performance, this unit stands out due to its innovative engineering and advanced features essential for tackling a variety of outdoor tasks.

One of the key features of the Shindaiwa C242/EVC engine is its lightweight construction. Weighing significantly less than many competitor models, it allows for easier maneuverability, particularly in time-sensitive applications such as lawn care, tree trimming, and agricultural work. This attribute is particularly beneficial for users who require prolonged usage without experiencing excessive fatigue.

The C242/EVC engine is equipped with Shindaiwa’s revolutionary 2-Stroke engine technology, which ensures a robust output while maintaining fuel efficiency. The engine’s advanced design allows for a higher power-to-weight ratio, making it ideal for heavy-duty tasks. Additionally, the unit incorporates an advanced cooling system that helps maintain optimal operating temperatures, thereby extending the engine's life and reducing downtime.

Another significant characteristic of the Shindaiwa C242/EVC is its user-friendly starting mechanism. The engine features an easy-start system that minimizes effort during ignition, enabling users to start their equipment quickly and efficiently, even in challenging conditions. This reliability is essential in professional environments where time is of the essence.

Furthermore, the Shindaiwa C242/EVC includes a sophisticated exhaust system designed to minimize emissions while maintaining optimal performance. This eco-friendly approach aligns with modern environmental standards, making it a suitable choice for landscape professionals who prioritize sustainability.

The unit also includes ergonomic handles, which are designed to provide comfort and control during operation. This feature reduces vibrations and helps operators maintain a firm grip, enhancing both precision and safety during use.

In summary, the Shindaiwa 89302 C242/EVC engine is a well-rounded solution for professionals seeking reliable, efficient, and powerful outdoor equipment. With its lightweight design, advanced engine technology, user-friendly features, and emphasis on eco-friendliness, it is an excellent choice for those committed to achieving high-quality results in landscaping and maintenance tasks. Its combination of performance, durability, and comfort positions the C242/EVC as a leader in the realm of outdoor power equipment.
Top Page Image Contents