Shindaiwa C242/EVC, 89302 manual Cutting Attachment Shield, Sub-Shield when trimmer head is in use

Page 7

Assembly (continued)

Cutting Attachment Shield

1.Insert the cutting attachment shield between the outer tube and the cutting attachment mounting plate.

NOTE:

It may be necessary to loosen the retain- ing nut and clamp screw to adjust cutting attachment shield mounting plate.

2.Fit the two spacers and the bracket over the outer tube and loosely install the four socket-head screws.

3.Tighten the four socket-head cap screws to secure the cutting attachment shield.

CAUTION!

Make sure the clamp screw and retaining nut are securely tightened before tightening the four socket-head

Socket-Head

Bracket

Outer Tube

Cap Screws

 

 

Spacer

 

 

Cutting Attachment

Shield w/subshield

 

Spacer

Retaining

Mounting Plate

Nut

 

Cutting attachment shield assembly

Sub-Shield (when trimmer head is in use)

cap screws.

WARNING!

NEVER operate the unit without the cutting attachment shield installed and tightly secured!

Installing a Trimmer Head

NOTE:

This unit is shipped with Holder A, Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT-HAND thread. Remove it by turning CLOCKWISE!

1.Attach the shield extension to the cut- ting attachment shield.

WARNING!

NEVER use this machine without sub-shield when using a trim- mer head.

CAUTION!

Make sure the sub-shield is completely hooked at the hook receiver.

Shaft Bolt

Bolt Guard

Holder B

Cutting Attachment Shield

Hook Receiver

Sub-shieldHook

Attach the shield extension to the cutting attachment shield

Hand-tighten Trimmer Head (counter-

clockwise to install)

1.With the gearcase output shaft facing up, rotate the gearshaft and Holder A until the hole in Holder A aligns with the matching hole in the gearcase flange, and then lock the holder to the gearcase by inserting the long end of the hex wrench through both holes.

2.Using the combination spark plug/ screwdriver wrench, remove the shaft bolt, bolt guard and Holder B. (The bolt guard and shaft bolt are not used with a trimmer head).

3.Install Holder B on the gearcase shaft. The splined hole on Holder B must engage with the gearcase shaft.

Gear Shaft

Holder A

 

 

 

Hex Wrench

 

 

 

 

4.

Using the hex wrench to secure Holder

 

 

 

This unit is now completely

 

A, install and hand-tighten the trimmer

 

 

head (counter-clockwise to install).

 

assembled and ready to use as a

5.

Remove the hex wrench from the

 

trimmer.

 

 

 

gearcase and holder.

 

 

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents English BrushcutterIntroduction ContentsStay Alert SafetySafety Labels Work SafelyBe Aware of the Working Environment Properly Equipped OperatorDo not make unauthorized Product DescriptionThese units or their components Install the handlebar AssemblyHandlebar Prior to Assembly Adjust throttle lever free playInstalling a Trimmer Head Sub-Shield when trimmer head is in useCutting Attachment Shield Install blade holder B on the output shaft Installing Brushcutter BladeRemove the hex wrench Minimize the Risk of Fire Mixing fuelFilling the fuel tank Examples of 501 mixing quantitiesStarting the Engine When the Engine StartsChecking Unit Condition Adjusting Engine IdleIdle Speed Adjustment Stopping the EngineOperation Brushcutter Handlebar Using a bladeBrushcutter Shoulder Strap Blade ThrustMaintenance Gearcase lubrication Hour maintenance10/15 hour maintenance Perform more frequently in dusty or Dirty conditionsRemove and replace the fuel filter element Every 135 hours of operation, remove and clean the mufflerMultiple-tooth Circular Blade Long Term StorageBlade Sharpening Shindaiwa Tornado BladePossible Cause Troubleshooting GuideEngine does not Start What To CheckWhat To Check Possible Cause Remedy LOW PowerAdditional Problems Emission System Warranty Statement NOTAs Remarques 731-3167, Japan Desmalezadora Etiquetas de seguridad IntroducciónContenido Declaraciones De SeguridadEtiquetas de seguridad SeguridadTrabaje con cuidado Mantengase AlertaMáquina descalzo Seguridad continuaciónEl operario debidamente equipado Esté alerta del area de trabajoC242 Descripción del ProductoMango tipo bicicleta Antes de Ensamblar EnsamblajeAjuste la holgura del acelerador Instalación del Cabezal de Nylon Ensamblaje continuacionProtector del accesorio de corte Protector Secundario cuando elInstalación de la cuchilla desmalezadora Disminuya el riesgo de incendios Mezcla de CombustibleLlenando el Tanque de Combustible Ejemplos de cantidades de mezcla a proporción deAl arrancar el motor Arranque del motor9HULÀTXHODFRQGLFLyQGHODXQLGDG Arranque del motor continuaciónApgado del motor Ajuste velocidad mínima del motorBordes OperaciónCorrea de Hombro Corte de Césped Máquinas Equipadas con Cabezal de CorteOperación continuación Mantenimiento Mantenimiento Cada 50 Horas Mantenimiento continuaciónMantenimiento Cada 10 Horas Mantenimiento Cada 10/15 HorasRetire el capuchón de la bujía Mantenimiento del silenciadorUse aceite con estabilizador de combustible Almacenamiento de Largo PlazoDisco Shindaiwa Tornado Discos de dientes múltiplesPosible causa Guia DiagnosticoEL Motor no Arranca Qué revisarDepósitos de carbonilla en el pistón o el silenciador Guia Diagnostico continuaciónBaja Potencia ¿Se sobrecalienta el motor?Otros Problemas Que Está Cubierto Por Esta Garantía Esta garantía es administrada porSus Derechos y Obligaciones de Garantía Cobertura de la Garantía del FabricanteSP22 SP23 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi Débroussailleuse Mises en garde Table des matièresÉtiquettes de sécurité SécuritéSécurité au travail Demeurer alerteÉquipement complet de l’utilisateur Sécurité suiteTenir compte de l’environnement de travail Caractéristiques techniques NomenclatureNe jamais effectuer des Réglage du jeu de la gâchette d’accélération AssemblageAvant l’assemblage GuidonPÁHFWHXU Assemblage suiteMontage de la tête de coupe De l’arbre du carter renvoi d’angle Installer le support de lame B sur l’ar- bre de sortie1HSDV¿HUGHODPHjXQ Bre de sortie du carter renvoi d’angleRéduire les risques d’incendie Mélange de carburantRemplissage du réservoir à carburant Exemples de quantités de mélange de carburant àLorsque le moteur démarre Démarrage du moteurContrôle de l’état de l’appareil Démarrage du moteur suiteArrêt du moteur Réglage du ralenti du moteurFonctionnement Fonctionnement suite Entretien Enlever et nettoyer la bougie Entretien suiteEntretien toutes les 10 heures Entretien toutes les 10 15 heuresEnlever le capuchon de la bougie Entretien toutes les 50 heuresEntretien du pare-étincelles Enlever et remplacer l’élément du filtreLame circulaire à plusieurs dents Remisage à long termeAffûtage de la lame Lame Shindaiwa TornadoPoints à contrôler SolutionGuide de dépannage LE Moteur NE Démarre PASLe moteur cogne Guide de dépannage suitePuissance Insuffisante Le moteur surchauffe-t-il ?Autres Problèmes Couverture de la garantie La présente garantie est administrée parVos droits et obligations en vertu de la garantie Couverture de la garantie des fabricantsFR22 FR23

C242/EVC, 89302 specifications

The Shindaiwa 89302 C242/EVC is a powerful and efficient engine specifically designed for professional landscaping and outdoor maintenance. Renowned for its durability and performance, this unit stands out due to its innovative engineering and advanced features essential for tackling a variety of outdoor tasks.

One of the key features of the Shindaiwa C242/EVC engine is its lightweight construction. Weighing significantly less than many competitor models, it allows for easier maneuverability, particularly in time-sensitive applications such as lawn care, tree trimming, and agricultural work. This attribute is particularly beneficial for users who require prolonged usage without experiencing excessive fatigue.

The C242/EVC engine is equipped with Shindaiwa’s revolutionary 2-Stroke engine technology, which ensures a robust output while maintaining fuel efficiency. The engine’s advanced design allows for a higher power-to-weight ratio, making it ideal for heavy-duty tasks. Additionally, the unit incorporates an advanced cooling system that helps maintain optimal operating temperatures, thereby extending the engine's life and reducing downtime.

Another significant characteristic of the Shindaiwa C242/EVC is its user-friendly starting mechanism. The engine features an easy-start system that minimizes effort during ignition, enabling users to start their equipment quickly and efficiently, even in challenging conditions. This reliability is essential in professional environments where time is of the essence.

Furthermore, the Shindaiwa C242/EVC includes a sophisticated exhaust system designed to minimize emissions while maintaining optimal performance. This eco-friendly approach aligns with modern environmental standards, making it a suitable choice for landscape professionals who prioritize sustainability.

The unit also includes ergonomic handles, which are designed to provide comfort and control during operation. This feature reduces vibrations and helps operators maintain a firm grip, enhancing both precision and safety during use.

In summary, the Shindaiwa 89302 C242/EVC engine is a well-rounded solution for professionals seeking reliable, efficient, and powerful outdoor equipment. With its lightweight design, advanced engine technology, user-friendly features, and emphasis on eco-friendliness, it is an excellent choice for those committed to achieving high-quality results in landscaping and maintenance tasks. Its combination of performance, durability, and comfort positions the C242/EVC as a leader in the realm of outdoor power equipment.
Top Page Image Contents