Shindaiwa C242/EVC, 89302 manual Long Term Storage, Blade Sharpening, Shindaiwa Tornado Blade

Page 17

Maintenance (continued)

Blade Sharpening

WARNING!

Wear protective gloves when handling or performing maintenance on the blade.

When the cutting edges of the blade become dull, they can be resharpened with a few strokes of a file. In order to keep the blade in balance, all cutting edges must be sharpened equally.

WARNING!

Sharpen only the cutting teeth of a blade. DO NOT alter the contour of the blade in any way.

Shindaiwa Tornado™ Blade

Round

File

The top plate of each tooth should angle back 30°

Shindaiwa Tornado™ Blade

To sharpen the cutters on a Shindaiwa Tornado™ Blade, use a 7/32-inch round file. File the leading edge of each tooth to a razor edge. The top plate of each tooth should angle back 30°.

Multiple-tooth Circular Blade

Round

File

Maintain a radius of 0.04 to 1 to 1.5 mm (0.06”) at the base of each tooth. Cutting edges must be offset equally on each side

Multiple-tooth Circular Blade

Use a round file to maintain a radius of 0.04 to 1 to 1.5 mm (0.06”) at the base of each tooth. Cutting edges must be offset equally on each side.

Long Term Storage

Whenever the unit will not be used for 30 days or longer, use the following proce- dures to prepare it for storage:

ŶClean external parts thoroughly.

ŶDrain all the fuel from the carburetor and the fuel tank.

IMPORTANT!

All stored fuels should be stabilized with a

fuel stabilizer such as STA-BIL, if oil with fuel stabilizer is not used.

CAUTION!

Gasoline stored in the carburetor for extended periods can cause hard start- ing, and could also lead to increased service and maintenance costs.

ŶRemove remaining fuel from the fuel lines and carburetor with the fuel drained from the fuel tank. To do so:

1.Prime the primer bulb until no more fuel is passing through.

2.Start and run the engine until it stops running.

3.Repeat steps 1 and 2 until the engine will no longer start.

ŶRemove the spark plug and pour about 7 mL (1/4 oz.) of 2-cycle mixing oil into the cylinder through the spark plug hole. Slowly pull the recoil starter 2 or 3 times so oil will evenly coat the interior of the engine. Reinstall the spark plug.

ŶBefore storing the unit, repair or replace any worn or damaged parts.

ŶRemove the air cleaner element from the carburetor and clean it thoroughly with soap and water, let dry and reas- semble the element.

ŶStore the unit in a clean, dust-free area.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents English BrushcutterIntroduction ContentsSafety Labels SafetyWork Safely Stay AlertBe Aware of the Working Environment Properly Equipped OperatorThese units or their components Product DescriptionDo not make unauthorized Handlebar Prior to Assembly AssemblyAdjust throttle lever free play Install the handlebarCutting Attachment Shield Sub-Shield when trimmer head is in useInstalling a Trimmer Head Remove the hex wrench Installing Brushcutter BladeInstall blade holder B on the output shaft Filling the fuel tank Mixing fuelExamples of 501 mixing quantities Minimize the Risk of FireStarting the Engine When the Engine StartsIdle Speed Adjustment Adjusting Engine IdleStopping the Engine Checking Unit ConditionOperation Brushcutter Shoulder Strap Using a bladeBlade Thrust Brushcutter HandlebarMaintenance 10/15 hour maintenance Hour maintenancePerform more frequently in dusty or Dirty conditions Gearcase lubricationRemove and replace the fuel filter element Every 135 hours of operation, remove and clean the mufflerBlade Sharpening Long Term StorageShindaiwa Tornado Blade Multiple-tooth Circular BladeEngine does not Start Troubleshooting GuideWhat To Check Possible CauseWhat To Check Possible Cause Remedy LOW PowerAdditional Problems Emission System Warranty Statement NOTAs Remarques 731-3167, Japan Desmalezadora Contenido IntroducciónDeclaraciones De Seguridad Etiquetas de seguridadTrabaje con cuidado SeguridadMantengase Alerta Etiquetas de seguridadEl operario debidamente equipado Seguridad continuaciónEsté alerta del area de trabajo Máquina descalzoC242 Descripción del ProductoAjuste la holgura del acelerador EnsamblajeMango tipo bicicleta Antes de Ensamblar Protector del accesorio de corte Ensamblaje continuacionProtector Secundario cuando el Instalación del Cabezal de NylonInstalación de la cuchilla desmalezadora Llenando el Tanque de Combustible Mezcla de CombustibleEjemplos de cantidades de mezcla a proporción de Disminuya el riesgo de incendiosAl arrancar el motor Arranque del motorApgado del motor Arranque del motor continuaciónAjuste velocidad mínima del motor 9HULÀTXHODFRQGLFLyQGHODXQLGDGCorrea de Hombro OperaciónCorte de Césped Máquinas Equipadas con Cabezal de Corte BordesOperación continuación Mantenimiento Mantenimiento Cada 10 Horas Mantenimiento continuaciónMantenimiento Cada 10/15 Horas Mantenimiento Cada 50 HorasRetire el capuchón de la bujía Mantenimiento del silenciadorDisco Shindaiwa Tornado Almacenamiento de Largo PlazoDiscos de dientes múltiples Use aceite con estabilizador de combustibleEL Motor no Arranca Guia DiagnosticoQué revisar Posible causaBaja Potencia Guia Diagnostico continuación¿Se sobrecalienta el motor? Depósitos de carbonilla en el pistón o el silenciadorOtros Problemas Sus Derechos y Obligaciones de Garantía Esta garantía es administrada porCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaSP22 SP23 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi Débroussailleuse Mises en garde Table des matièresSécurité au travail SécuritéDemeurer alerte Étiquettes de sécuritéTenir compte de l’environnement de travail Sécurité suiteÉquipement complet de l’utilisateur Ne jamais effectuer des NomenclatureCaractéristiques techniques Avant l’assemblage AssemblageGuidon Réglage du jeu de la gâchette d’accélérationMontage de la tête de coupe Assemblage suitePÁHFWHXU 1HSDV¿HUGHODPHjXQ Installer le support de lame B sur l’ar- bre de sortieBre de sortie du carter renvoi d’angle De l’arbre du carter renvoi d’angleRemplissage du réservoir à carburant Mélange de carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieLorsque le moteur démarre Démarrage du moteurArrêt du moteur Démarrage du moteur suiteRéglage du ralenti du moteur Contrôle de l’état de l’appareilFonctionnement Fonctionnement suite Entretien Entretien toutes les 10 heures Entretien suiteEntretien toutes les 10 15 heures Enlever et nettoyer la bougieEntretien du pare-étincelles Entretien toutes les 50 heuresEnlever et remplacer l’élément du filtre Enlever le capuchon de la bougieAffûtage de la lame Remisage à long termeLame Shindaiwa Tornado Lame circulaire à plusieurs dentsGuide de dépannage SolutionLE Moteur NE Démarre PAS Points à contrôlerPuissance Insuffisante Guide de dépannage suiteLe moteur surchauffe-t-il ? Le moteur cogneAutres Problèmes Vos droits et obligations en vertu de la garantie La présente garantie est administrée parCouverture de la garantie des fabricants Couverture de la garantieFR22 FR23

C242/EVC, 89302 specifications

The Shindaiwa 89302 C242/EVC is a powerful and efficient engine specifically designed for professional landscaping and outdoor maintenance. Renowned for its durability and performance, this unit stands out due to its innovative engineering and advanced features essential for tackling a variety of outdoor tasks.

One of the key features of the Shindaiwa C242/EVC engine is its lightweight construction. Weighing significantly less than many competitor models, it allows for easier maneuverability, particularly in time-sensitive applications such as lawn care, tree trimming, and agricultural work. This attribute is particularly beneficial for users who require prolonged usage without experiencing excessive fatigue.

The C242/EVC engine is equipped with Shindaiwa’s revolutionary 2-Stroke engine technology, which ensures a robust output while maintaining fuel efficiency. The engine’s advanced design allows for a higher power-to-weight ratio, making it ideal for heavy-duty tasks. Additionally, the unit incorporates an advanced cooling system that helps maintain optimal operating temperatures, thereby extending the engine's life and reducing downtime.

Another significant characteristic of the Shindaiwa C242/EVC is its user-friendly starting mechanism. The engine features an easy-start system that minimizes effort during ignition, enabling users to start their equipment quickly and efficiently, even in challenging conditions. This reliability is essential in professional environments where time is of the essence.

Furthermore, the Shindaiwa C242/EVC includes a sophisticated exhaust system designed to minimize emissions while maintaining optimal performance. This eco-friendly approach aligns with modern environmental standards, making it a suitable choice for landscape professionals who prioritize sustainability.

The unit also includes ergonomic handles, which are designed to provide comfort and control during operation. This feature reduces vibrations and helps operators maintain a firm grip, enhancing both precision and safety during use.

In summary, the Shindaiwa 89302 C242/EVC engine is a well-rounded solution for professionals seeking reliable, efficient, and powerful outdoor equipment. With its lightweight design, advanced engine technology, user-friendly features, and emphasis on eco-friendliness, it is an excellent choice for those committed to achieving high-quality results in landscaping and maintenance tasks. Its combination of performance, durability, and comfort positions the C242/EVC as a leader in the realm of outdoor power equipment.
Top Page Image Contents