Shindaiwa 89302, C242/EVC manual Remove and replace the fuel filter element

Page 16

Maintenance (continued)

50 hour maintenance

Remove and replace the fuel filter element.

Before reinstalling the new filter element, inspect the condition of all the fuel system components (fuel pick-up line, fuel return line, tank vent line, tank vent, fuel cap and fuel tank). If damage, splitting or deterioration is noted, the unit should be removed from ser- vice until it can be inspected or repaired by a Shindaiwa-trained service technician.

CAUTION!

Make sure you do not pierce the fuel line with the end of the hooked wire. The line is delicate and can be dam- aged easily.

0XIÁHU DLQWHQDQFH

Engine Cover

Screws

Hooked wire

)XHO¿OWHUPDLQWHQDQFH)XHO¿OWHUHOHPHQW

Engine Cover

0XIÀHU&RYHU

0XIÀHU Screws

Gasket

Screws

Spark Arrester Spark Arrester Outlet

Screen

Cover

HU*DVNHW

Every 135 hours of operation, remove and clean the muffler.

WARNING!

Never operate the unit with DGDPDJHRUPLVVLQJPXIÀHURUVSDUN arrester! Operating with a missing or GDPDJHGVSDUNDUUHVWHULVD¿UHKD]DUG and could also damage your hearing.

If the engine becomes sluggish and low on power, check and clean the spark arrester

screen.

1.Remove the spark plug boot.

2.With a 4mm hex wrench remove the 1 muffler cover and 3 engine cover screws and the engine cover. The muf- fler cover is attached to the engine cover at the top and front by tabs. To remove push inward at arrow area while pulling outward. See insert image.

3.With a Phillips type screwdriver remove the 5 screws holding the spark arrester screen and cover to the muffler.

4.Remove the screen and clean it with a stiff bristle brush.

5.Remove the 3 muffler bolts and the muffler.

6.Inspect the cylinder exhaust port for any carbon buildup.

7.Gently tap the muffler on a wood sur- face to dislodge any loose carbon.

8.Reassemble the spark arrester, muffler and engine cover in the reverse order of disassembly.

IMPORTANT!

If you note excessive carbon buildup, consult with an authorized Shindaiwa servicing dealer.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Brushcutter EnglishContents IntroductionSafety Safety LabelsWork Safely Stay AlertProperly Equipped Operator Be Aware of the Working EnvironmentDo not make unauthorized Product DescriptionThese units or their components Assembly Handlebar Prior to AssemblyAdjust throttle lever free play Install the handlebarInstalling a Trimmer Head Sub-Shield when trimmer head is in useCutting Attachment Shield Install blade holder B on the output shaft Installing Brushcutter BladeRemove the hex wrench Mixing fuel Filling the fuel tankExamples of 501 mixing quantities Minimize the Risk of FireWhen the Engine Starts Starting the EngineAdjusting Engine Idle Idle Speed AdjustmentStopping the Engine Checking Unit ConditionOperation Using a blade Brushcutter Shoulder StrapBlade Thrust Brushcutter HandlebarMaintenance Hour maintenance 10/15 hour maintenancePerform more frequently in dusty or Dirty conditions Gearcase lubricationEvery 135 hours of operation, remove and clean the muffler Remove and replace the fuel filter elementLong Term Storage Blade SharpeningShindaiwa Tornado Blade Multiple-tooth Circular BladeTroubleshooting Guide Engine does not StartWhat To Check Possible CauseLOW Power What To Check Possible Cause RemedyAdditional Problems Emission System Warranty Statement NOTAs Remarques 731-3167, Japan Desmalezadora Introducción ContenidoDeclaraciones De Seguridad Etiquetas de seguridadSeguridad Trabaje con cuidadoMantengase Alerta Etiquetas de seguridadSeguridad continuación El operario debidamente equipadoEsté alerta del area de trabajo Máquina descalzoDescripción del Producto C242Mango tipo bicicleta Antes de Ensamblar EnsamblajeAjuste la holgura del acelerador Ensamblaje continuacion Protector del accesorio de corteProtector Secundario cuando el Instalación del Cabezal de NylonInstalación de la cuchilla desmalezadora Mezcla de Combustible Llenando el Tanque de CombustibleEjemplos de cantidades de mezcla a proporción de Disminuya el riesgo de incendiosArranque del motor Al arrancar el motorArranque del motor continuación Apgado del motorAjuste velocidad mínima del motor 9HULÀTXHODFRQGLFLyQGHODXQLGDGOperación Correa de HombroCorte de Césped Máquinas Equipadas con Cabezal de Corte BordesOperación continuación Mantenimiento Mantenimiento continuación Mantenimiento Cada 10 HorasMantenimiento Cada 10/15 Horas Mantenimiento Cada 50 HorasMantenimiento del silenciador Retire el capuchón de la bujíaAlmacenamiento de Largo Plazo Disco Shindaiwa TornadoDiscos de dientes múltiples Use aceite con estabilizador de combustibleGuia Diagnostico EL Motor no ArrancaQué revisar Posible causaGuia Diagnostico continuación Baja Potencia¿Se sobrecalienta el motor? Depósitos de carbonilla en el pistón o el silenciadorOtros Problemas Esta garantía es administrada por Sus Derechos y Obligaciones de GarantíaCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaSP22 SP23 Tualatin, Oregon 97062 USA 11, Ozuka-Nishi Débroussailleuse Table des matières Mises en gardeSécurité Sécurité au travailDemeurer alerte Étiquettes de sécuritéÉquipement complet de l’utilisateur Sécurité suiteTenir compte de l’environnement de travail Caractéristiques techniques NomenclatureNe jamais effectuer des Assemblage Avant l’assemblageGuidon Réglage du jeu de la gâchette d’accélérationPÁHFWHXU Assemblage suiteMontage de la tête de coupe Installer le support de lame B sur l’ar- bre de sortie 1HSDV¿HUGHODPHjXQBre de sortie du carter renvoi d’angle De l’arbre du carter renvoi d’angleMélange de carburant Remplissage du réservoir à carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieDémarrage du moteur Lorsque le moteur démarreDémarrage du moteur suite Arrêt du moteurRéglage du ralenti du moteur Contrôle de l’état de l’appareilFonctionnement Fonctionnement suite Entretien Entretien suite Entretien toutes les 10 heuresEntretien toutes les 10 15 heures Enlever et nettoyer la bougieEntretien toutes les 50 heures Entretien du pare-étincellesEnlever et remplacer l’élément du filtre Enlever le capuchon de la bougieRemisage à long terme Affûtage de la lameLame Shindaiwa Tornado Lame circulaire à plusieurs dentsSolution Guide de dépannageLE Moteur NE Démarre PAS Points à contrôlerGuide de dépannage suite Puissance InsuffisanteLe moteur surchauffe-t-il ? Le moteur cogneAutres Problèmes La présente garantie est administrée par Vos droits et obligations en vertu de la garantieCouverture de la garantie des fabricants Couverture de la garantieFR22 FR23

C242/EVC, 89302 specifications

The Shindaiwa 89302 C242/EVC is a powerful and efficient engine specifically designed for professional landscaping and outdoor maintenance. Renowned for its durability and performance, this unit stands out due to its innovative engineering and advanced features essential for tackling a variety of outdoor tasks.

One of the key features of the Shindaiwa C242/EVC engine is its lightweight construction. Weighing significantly less than many competitor models, it allows for easier maneuverability, particularly in time-sensitive applications such as lawn care, tree trimming, and agricultural work. This attribute is particularly beneficial for users who require prolonged usage without experiencing excessive fatigue.

The C242/EVC engine is equipped with Shindaiwa’s revolutionary 2-Stroke engine technology, which ensures a robust output while maintaining fuel efficiency. The engine’s advanced design allows for a higher power-to-weight ratio, making it ideal for heavy-duty tasks. Additionally, the unit incorporates an advanced cooling system that helps maintain optimal operating temperatures, thereby extending the engine's life and reducing downtime.

Another significant characteristic of the Shindaiwa C242/EVC is its user-friendly starting mechanism. The engine features an easy-start system that minimizes effort during ignition, enabling users to start their equipment quickly and efficiently, even in challenging conditions. This reliability is essential in professional environments where time is of the essence.

Furthermore, the Shindaiwa C242/EVC includes a sophisticated exhaust system designed to minimize emissions while maintaining optimal performance. This eco-friendly approach aligns with modern environmental standards, making it a suitable choice for landscape professionals who prioritize sustainability.

The unit also includes ergonomic handles, which are designed to provide comfort and control during operation. This feature reduces vibrations and helps operators maintain a firm grip, enhancing both precision and safety during use.

In summary, the Shindaiwa 89302 C242/EVC engine is a well-rounded solution for professionals seeking reliable, efficient, and powerful outdoor equipment. With its lightweight design, advanced engine technology, user-friendly features, and emphasis on eco-friendliness, it is an excellent choice for those committed to achieving high-quality results in landscaping and maintenance tasks. Its combination of performance, durability, and comfort positions the C242/EVC as a leader in the realm of outdoor power equipment.
Top Page Image Contents