MTD YM75 manual Spark Arrestor Maintenance, Reinstalling the Air Filter/Muffler Cover

Page 16

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS

6.Replace the air filter inside the air filter/muffler cover. See Figure 27.

NOTE: Operating the unit without the air filter and air filter/muffler cover assembly, will VOID the warranty.

Reinstalling the Air Filter/Muffler Cover

1.Place the air filter/muffler cover over the back of the carburetor and muffler. Align the screw holes.

2.Insert the four (4) screws into the holes in the air filter/muffler cover and tighten. See Figure 26.

Do not over tighten.

Spark Arrestor Maintenance

1.Remove air filter/muffler cover. See Removing the Air Filter/Muffler Cover.

2.Locate muffler front and the two (2) bolts securing it to the engine. See Figure 31. Remove the two (2) bolts using a flatblade screwdriver or 5/16-inch socket or nut driver. Pull muffler off of the engine.

3.Turn muffler over to the back side and locate the exhaust gasket. Remove the muffler gasket from the muffler. See Figure 31.

NOTE: If the exhaust gasket is torn or damaged, replace it with a new gasket before reassembling muffler.

4.Using a small flatblade screwdriver, carefully pry up the spark arrestor from the recessed hole. See Figure 32. Remove the spark arrestor from the muffler.

5.Clean the spark arrestor with a wire brush. Replace it if it is damaged or if it is impossible to clean thoroughly. See Figure 32.

6.Reinstall the spark arrestor by pressing it into the recessed hole on the muffler's back side. Make sure it fits tightly against the muffler and is not raised up.

7.Place the exhaust gasket against muffler's back side. Align the gasket bolt holes with the bolt holes in the muffler. While holding exhaust gasket in place, insert the bolts into the muffler's front side. See Figure 31.

8.Place the muffler (with the exhaust gasket in place and bolts inserted), against the engine, aligning the bolt holes. Tighten the bolts to secure the muffler to the engine. If using a torque wrench torque to:

80-90 in.•lb. (9-10.2 N•m).

WARNING: If the muffler is not tightened securely, it could fall off causing damage to the unit and possible serious personal injury.

9. Reinstall the air filter/muffler cover.

Bolts

Spark

Exhaust

 

Arrestor

Gasket

Muffler - Front Side

Muffler - Back Side

Figure 31

 

Spark

 

Arrestor

Flat blade

 

 

Screwdriver

Spark Arrestor

Muffler - Back Side

Figure 32

16

Image 16
Contents Operator’s Manual Visit OUR WEB Site Important Safe Operation Practices Before OperatingOther Safety Warnings Safety Warnings for Gas TrimmersWhile Operating BSAFETY & International Symbols Know Your Unit ApplicationsInstalling and Adjusting the D-handle Assembly InstructionsOIL and Fuel Information Oil and Fuel Mixing InstructionsStarting Instructions STARTING/STOPPING InstructionsStopping Instructions Installing the Cutting Attachment or Add-On Operating InstructionsOperating the EZ-Link System Removing the Cutting Attachment or Add-OnsAdjusting Trimming Line Length Holding the TrimmerTips for Best Trimming Results Decorative TrimmingMaintenance and Repair Instructions Maintenance ScheduleLine Installation Winding the Inner Reel with New LineInstalling a Pre-wound Reel SpeedSpool Replacement Parts Cleaning the SpeedSpoolReleasing the Inner Reel Cleaning the Air Filter Air Filter MaintenanceRemoving the Air Filter/Muffler Cover Spark Arrestor Maintenance Reinstalling the Air Filter/Muffler CoverCarburetor Adjustment Clean Air FilterAdjust Idle Speed Check Fuel MixtureCleaning Accessories/Replacement PartsReplacing the Spark Plug Long Term StorageTroubleshooting Guide Trouble Possible Causes Corrective ActionEngine SpecificationsDrive Shaft and Cutting Attachment EPA Emission Control Warranty Statement MTD LLC Manuel de lutilisateur Table DES Matières Consignes DE Sécurité CaliforniePendant L’utilisation de L’appareil Symboles DE Sécurité ET Internationaux FAMILIARISEZ-VOUS Avec LA Désherbeuse ApplicationsInstallation ET Réglage DE LA Poignée EN D Instructions DE MontageFonctionnement DE LA Désherbeuse Mélange Dhuile ET DE CarburantInstructions DE Démarrage Instructions DE Démarrage ET ArrêtInstructions Darrêt Retrait de laccessoire de coupe ou autre Mode D’EMPLOInstallation de laccessoire de coupe ou autre Tenue DE LA Désherbeuse Réglage DE LA Longueur DU FILConseils Pour Bien Désherber Coupe DécorativeInstallation DU FIL Instructions D’ENTRETIEN ET RéparationsProgramme Dentretien Rembobiner le fil neuf sur le moulinet intérieurInstallation dun moulinet pré-enroulé Déroulement du moulinet intérieur Retrait du couvercle du filtre à air/silencieux Entretien DU Filtre À AIRNettoyage du filtre à air Réinstallation du couvercle du filtre à air/silencieux Entretien DU PARE-ÉTINCELLESVérification du mélange de carburant Réglage DU CarburateurRéglage du ralenti Remplacement DE LA Bougie ACCESSOIRES/PIÈCES DE RechangeEntreposage Entreposage DE Longue DuréeProblème Causes possibles Solution Guide DE DépannageCaracteristiques Arbre Dentrainement et Accessoire de CoupeMoteur Garantie portant sur les normes antipollution de lEPA Garantie Limitée DU Fabricant Pour Manuel del Dueño/Operador Visite Nuestra Sito EN EL Internet Sección 1 Normas Para UNA Operacion Segura ParachispasAdvertencias de Seguridad Para Gasolina Sección 1b Símbolos DE Seguridad E Internacionales Sección 2 Conozca SU Recortador AplicacionesSección 3 Intrucciones DE Ensamble Instalación Y Ajuste DE LA Manija EN DSección 4 Informacion DEL Aceite Y DEL Combusible Instrucciones Para Mezclar EL Aceite Y EL CombustibleDefinición de los combustibles mezclados Uso de combustibles mezcladosInstrucciones DE Arranque Sección 5 Instrucciones DE Arranque Y ApagadoInstrucciones DE Apagado Sección 6 Instrucciones DE OPERACIóN Consejos Para Obtener Mejores Resultados AL Recortar Como Sostener EL RecortadorRecorte Decorativo Instalación DE LA Línea Programa DE MantenimientoBobinado del carrete interior con línea nueva Instalación de un carrete interior prebobinado Limpieza DEL Speedspool Desconexión del carrete interiorMantenimiento DEL Filtro DE Aire Limpieza del Filtro de AireMantenimiento DEL Parachispas Ajuste DEL Carburador Verifique la mezcla del combustibleLimpie el filtro de aire Ajuste para marcha en vacíoCambio DE LA Bujia DE Encendido ACCESORIOS/PIEZAS DE RepuestoAlmacenamiento Almacenamiento ProlongadoProblema Causas posibles Medidas correctivas Sección 8 Guía Para Solución DE DesperfectosMotor Sección 9 EspecificacionesEje Impulsor y Accesorio de Corte Responsabilidades de Garantía de los Propietarios Notas E23 Parts List Engine Parts Model YM75 2-CYCLE GAS TrimmerBoom and Trimmer Parts Garantía Limitada DEL Fabricante Para

YM75 specifications

The MTD YM75 is a compact and efficient tractor designed for a variety of agricultural and landscaping tasks. Known for its versatility and robust performance, the YM75 is favored by many small-scale farmers and landowners looking to enhance their productivity.

One of the standout features of the MTD YM75 is its powerful engine. The tractor is equipped with a reliable diesel engine that has a displacement of 1.7 liters, delivering around 75 horsepower. This impressive power allows the YM75 to tackle tough tasks such as plowing, tilling, and hauling materials with ease. The efficiency of its engine not only provides ample power but also ensures lower fuel consumption, making it economical for long-term use.

The MTD YM75 incorporates advanced technologies that make it user-friendly and efficient. The tractor features a synchronized transmission system, allowing for smooth gear shifts and precise control over speed and torque. This is particularly beneficial when operating various implements or navigating challenging terrains. Additionally, the tractor's compact design enables it to maneuver effortlessly in tight spaces, making it suitable for small farms and gardens.

The hydraulic system of the YM75 is another highlight, boasting a high lifting capacity. This enables the attachment of various implements, such as front loaders, backhoes, and other tools, enhancing the tractor's versatility. The hydraulic setup is designed to be responsive, providing operators with the ability to control attachments with precision.

In terms of operator comfort, the MTD YM75 does not disappoint. It features an ergonomic cabin with adjustable seating, providing a comfortable driving experience even during long working hours. The controls are intuitively placed, allowing for easy access and minimizing distractions while operating the machinery.

Durability is a key characteristic of the MTD YM75. Built with high-quality materials and robust construction, this tractor is designed to withstand the rigors of daily agricultural work. Its rugged tires ensure excellent traction and stability on various terrains, contributing to its overall reliability.

In summary, the MTD YM75 is a powerful, versatile, and user-friendly tractor that meets the needs of modern farmers and landscapers. With its efficient engine, advanced hydraulic system, ergonomic design, and durability, it stands out as an excellent choice for enhancing productivity in any agricultural setting. Whether for tilling the land or managing landscaping projects, the YM75 proves to be an invaluable asset.