Black & Decker GH3000 instruction manual Operation

Page 6

heavy enough to carry the current your product will draw. An undersized cord will cause a drop

in line voltage resulting in loss of power and overheating. The table shows the correct size to use

depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord. If the extension will be used outside, the

cord must be suitable for outdoor work. The letters “WA” on the cord jacket indicate that the cord

is suitable for outdoor use.

 

 

 

 

FUNCTIONAL DESCRIPTION (figure A)

7.

Trimmer Head

1.

On/Off Trigger Switch

4.

Auxiliary Handle

2.

Handle

5.

Height Adjust Locking Clamp

8.

Edge Guide Wheel

3.

Power Cord Plug

6.

Trimmer Guard

9.

Spool Housing

ASSEMBLY

 

 

 

 

ASSEMBLY TOOLS REQUIRED (NOT SUPPLIED): Phillips Screwdriver

WARNING: Unplug the appliance before attempting to attach the guard.

Attaching the guard (Figures B, C)

WARNING: NEVER OPERATE Appliance WITHOUT GUARD FIRMLY IN PLACE.

The guard must always be properly attached on the appliance to protect the user.

• Remove the screw from the guard.

• Keeping the guard square to the trimmer head slide it into place until the retaining tab clicks into place (Ensure that the guide rails (B1) on the guard (B2) are correctly aligned with the guide rails (B3) on the trimmer head (B4) (figure B).

• Secure the guard with the screw (C1) (figure C).

Attaching the Auxiliary Handle (Figures D, E)

• To attach the handle, press in on the buttons (D1) on both sides of the upper housing as shown in figure D.

• Position the handle as shown in figure E (with the Black & Decker logo facing upward). Partially push the handle on so that it will hold the buttons in when you release them with your hand.

• Push the handle completely onto the housing and position it slightly until it “snaps” into place (figure E).

• To adjust the handle up or down, press in on the button (F1) and raise or lower the handle.

• The handle should be adjusted so that your front arm is straight when the trimmer is in the working position.

Adjusting the height of the appliance (figure G)

This appliance has a telescopic mechanism, allowing you to set it to a comfortable height. To adjust the height setting:

• Release the height adjust locking clamp (G1).

• Gently pull the tube (G2) up or down to the desired height.

• Close the height adjust locking clamp (G1).

OPERATION

WARNING: Always use proper eye protection that conforms to ANSI Z87.1 (CAN/CSA Z94.3) while operating this power appliance.

WARNING: Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the appliance accidentally.

CAUTION: Before you begin trimming, only use the appropriate type of cutting line.

CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the appliance, such as barbs at the base of a chain link fence.

Switching on and off (figure H)

WARNING: Never attempt to lock the trigger switch in the on position.

• To turn the appliance on, squeeze the trigger switch (H1)

• To turn the appliance off, release the trigger switch (H1).

EXTENSION Cord Retainer (figure I)

WARNING: Ensure the trigger switch is not engaged to reduce the risk of starting the appliance accidentally.

A cord retainer is incorporated into the rear of the handle on the power head.

6

Image 6
Contents Trimmer/Edger 10 O Safety Guidelines Definitions Important Safety Warnings and Instructions Read All InstructionsSafety Warnings and Instructions Polarized Plugs Safety Warnings and Instructions Extension CordsAdditional Warnings for String Trimmers Operation Edging mode Choosing trimming or edging mode figures L, MTrimming mode Operating the trimmer figureS j, KREPLACING THE SPOOL figures N, O, P, Q Rewinding Spool figures R, STroubleshooting MaintenanceService Information Full Two-Year Home Use Warranty TAILLE-BORDURE COUPE-BORDURE Lignes directrices en matière de sécurité définitions Réduction DES Risques DE BlessuresPage Description Fonctionnelle Figure a Tête de coupePare-main du taille-bordure Boîtier de la bobine Reglage DE LA Hauteur DE L’OUTIL figure G Fixation DU PARE-MAIN Figures B, CFixation DE LA Poignee Auxiliaire Figures D, E FonctionnementFonctionnement DU TAILLE-BORDURE figureS j, K Mode DE TaillageMode DE Coupe EN Bordure Coupe EN BordureDésobstruction ET Désenchevêtrement DU FIL figures N, O, P REMPLACER LA BOBINE figures N, O, P, QProblème Solution possible Cause possible Rembobinage DE LA Bobine figures R, SDépannage Black & Decker au Voir la rubriqueDE Podadora Bordeadora Pautas DE SEGURIDAD/DEFINICIONES Advertencias E Instrucciones Importantes Sobre SeguridadConserve Estas Instrucciones Será el cable. Si se utilizará el cable El enchufe del cable prolongador de ninguna maneraEl número de calibre, más grueso Libre. Las letras WA en la cubiertaAjuste DE LA Altura DE LA Herramienta Figura G Instalación DEL Protector Figuras B Y CInstalación DEL Mango Auxiliar Figuras D Y E FuncionamientoModo DE Bordeado Elección DEL Modo DE Poda O Bordeado Figuras L Y MModo DE Poda Precaución BordeadoEliminación DE Atascos Y Cuerdas Enredadas Figuras N, O Y P REMPLAZO DEL CARRETE figurAs N, O, P Y QProblema Rebobinado DEL Carrete figurAs R Y SCausa posible Solución posible Mantenimiento Telephone · No. Teléfono Años DE GarantiaFerre Pat de Puebla, S.A. de C.V. Ejército Mexicano No Grupo Realsa en herramientas, S.A. de C.VFerre Pat de Puebla, S.A. de C.V Servicio de Fabrica Black & Decker, S.A. de C.VPage Page Catalog Number GH3000