Status LED «MODE» | Albatron Technology ARM11/Cortex-A8 specs

bdiGDB for GNU Debugger, BDI2000 (ARM11/Cortex-A8)

User Manual 13

2.3 Status LED «MODE»

The built in LED indicates the following BDI states:

Rev. A

	BDI TRGT MODE	BDI MAIN				BDI OPTION

Rev. B/C

	BDI TRGT MODE	TARGET A				TARGET B

MODE LED	BDI STATES

OFF	The BDI is ready for use, the ﬁrmware is already loaded.

ON	The power supply for the BDI2000 is < 4.75VDC.

BLINK	The BDI «loader mode» is active (an invalid ﬁrmware is loaded or loading ﬁrmware is active).

© Copyright 1997-2007 by ABATRON AG Switzerland

V 1.04

Image 13

Albatron Technology ARM11/Cortex-A8 user manual Status LED «MODE», Built in LED indicates the following BDI states

Contents

BdiGDB Using bdiGDB InstallationIntroduction BDI2000 BDI Conﬁguration Appendices Troubleshooting Maintenance Trademarks BDI2000 Introduction BDI Conﬁguration Connecting the BDI2000 to Target InstallationFor BDI Main / Target a connector signals see table on next Jtag Test Reset BDI Main / Target a Connector Signals Changing Target Processor Type Adaptive Clocking For Target B connector signals see table on next Returned Jtag Test Clock BDI Target B Connector Signals External power supply Target system Please switch on the system in the following sequence 142 Power Supply from Target System Built in LED indicates the following BDI states Status LED «MODE» RS232 Connector Ethernet communication BASE-T ConnectorPC Host Name Description Overview of an installation / conﬁguration process Installation of the Conﬁguration SoftwareActivating Bootp Load/Update the BDI ﬁrmware/logic Build the setup tool1 Conﬁguration with a Linux / Unix host Following the steps to bring-up a new BDI2000 Transmit the initial conﬁguration parameters Check conﬁguration and exit loader modeﬁle name without any path For more information about Tftp use man tftpd Ory / programmable logic 2 Conﬁguration with a Windows host Reassemble the unit as described in Appendix «Maintenance» Recover procedure Tftp server for Windows NT Testing the BDI2000 to host connection Principle of operation Using bdiGDB Conﬁguration File Part Init BdiGDB for GNU Debugger, BDI2000 ARM11/Cortex-A8 ROM on the target, select ROM as the format Using a startup program to initialize the target systemFormat COFF, SREC, AOUT, BIN, ELF or ROM Example Format Coff Cputype ARM1136 Part TargetNone Pushpull Stop HaltRUN Loadonly Hard SoftBreakmode Hard Core Daisy chained Jtag devices Low level Jtag scan chain conﬁguration Part Host Dump ﬁlename Prompt ARM11 Part Flash BLOCK, CHIP, Unlock AM29BX8 MIRRORX8, I28BX8 STRATAX8, AT49X8 Supported Flash Memories Tor. In other words, this is the size of one sector in bytes Or use the Telnet unlock command Part Regs Entry in the conﬁguration ﬁle Example for a register deﬁnitionRegister deﬁnition ﬁle Connecting to the target Target setupDebugging with GDB Breakpoint Handling GDB monitor command Target serial I/O via BDI Target DCC I/O via BDI Telnet Interface Dump Command list Some examples CP15 ID register CRn = 0, opcode2 = CPxx RegistersCP15 Cache Type CRn = 0, opcode2 = CP15 Invalidate I cache line CRn = 7, opcode2 = 1, CRm = Multi-Core Support BASE-T Speciﬁcations Declaration of Conformity CE Environmental notice Warranty Problem Troubleshootingﬁrmware can not be loaded Possible reasons Unplug the cables Maintenance Reinstallation All trademarks are property of their respective holders Trademarks