Alliance Laundry Systems HX, SX, UX OPL Cycle 39 — Test Program

				Section 4 Service Procedures
			Cycle 39 — Test Program
Step	Description	Min:sec	Step Definition	Corrective Action
1	Cold Fill to	0:30	The machine should fill with cold water to	Refer to the “Machine Did Not Fill Alarm
	High Level		high level within 30 seconds and, when it	Analysis” flowchart.
			does, a buzzer will sound.
2	Drain 1	0:10	The machine should drain within 10 seconds	Refer to the “Empty Alarm Analysis”
			and, when it does, a buzzer will sound.	flowchart.
3	Hot Fill to Low	5:00	The machine should fill with hot water to low	Refer to the “Machine Did Not Fill Alarm
	Level		level within 5 minutes and, when it does, a	Analysis” flowchart.
			buzzer will sound.
4	Auxiliary Fill	5:00	The machine should fill with water to	Refer to the “Machine Did Not Fill Alarm
	to Medium		medium level within 5 minutes and, when it	Analysis” flowchart.
	Level		does, a buzzer will sound.
5	Heat (150°F)	1h00	This step is needed only if the machine is	Check the components used for the
			equipped with auxiliary heat (e.g., steam or	auxiliary heating (e.g., steam valve or
			electric heating). If the temperature isn’t	heating elements).
			reached within the time programmed, an
			alarm will sound.
6	Cold Fill to	0:30	The machine should fill with cold water to	Refer to the “Machine Did Not Fill Alarm
	High Level		high level within 30 seconds and, when it	Analysis” flowchart.
			does, a buzzer will sound.
7	Supply 1	0:30	Supply compartment A should flush for 30	Refer to the “No Fill Analysis” flowchart.
			seconds.
8	Supply 2	0:30	Supply compartment B should flush for 30	Refer to the “No Fill Analysis” flowchart.
			seconds.
9	Supply 3	0:30	Supply compartment C should flush for 30	Refer to the “No Fill Analysis” flowchart.
			seconds.
10	Supply 4	0:30	Supply relay 1 should be activated for 30	Refer to the “No Fill Analysis” flowchart.
			seconds.
11	Supply 5	0:30	Supply relay 2 should be activated for 30	Refer to the “No Fill Analysis” flowchart.
			seconds.
12	Supply 6	0:30	Supply relay 3 should be activated for 30	Refer to the “No Fill Analysis” flowchart.
			seconds.
13	Supply 7	0:30	Supply relay 4 should be activated for 30	Refer to the “No Fill Analysis” flowchart.
			seconds.
14	Supply 8	0:30	Supply relay 5 should be activated for 30	Refer to the “No Fill Analysis” flowchart.
			seconds.
15	Supply 9	0:30	Supply relay 6 should be activated for 30	Refer to the “No Fill Analysis” flowchart.
			seconds.
16	Wash 2 3/27	0:30	The basket should rotate forward 3 seconds,	Refer to the “No Motor Operation (With or
	(80°F)		pause for 27 seconds, rotate in reverse for 3	With No AC Drive Fault” flowchart.
			seconds, pause for 27 seconds, etc.
17	Wash 3, no	0:30	The basket should not rotate for 30 seconds.	If the basket does rotate, check the
	agitation (80°F)			program.
18	Wash 4 10/3	0:30	The basket should rotate forward 10 seconds,	Refer to the “No Motor Operation (With or
	(80°F)		pause for 3 seconds, rotate in reverse for 10	With No AC Drive Fault” flowchart.
			seconds, pause for 3 seconds, etc.
19	Wash 1, no	0:30	The basket should rotate forward for 30	Refer to the “No Motor Operation (With or
	reverse (80°F)		seconds without pausing.	With No AC Drive Fault” flowchart.
20	Drain 1	1:00	The machine should drain within 1 minute	Refer to the “Empty Alarm Analysis”
			and, when it does, a buzzer will sound.	flowchart.

Table 1

9001900 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 67